Biomechanical evaluation of two methods of fixation of a flexor hallucis longus tendon graft.

Aims: The traditional transosseus flexor hallucis longus (FHL) tendon transfer for patients with Achilles tendinopathy requires two incisions to harvest a long tendon graft. The use of a bio-tenodesis screw enables a short graft to be used and is less invasive, but lacks supporting evidence about its biomechanical behaviour. We aimed, in this study, to compare the strength of the traditional transosseus tendon-to-tendon fixation with tendon-to-bone fixation using a tenodesis screw, in cyclical loading and ultimate load testing. Materials and Methods: Tendon grafts were undertaken in 24 paired lower-leg specimens and randomly assigned in two groups using fixation with a transosseus suture (suture group) or a tenodesis screw (screw group). The biomechanical behaviour was evaluated using cyclical and ultimate loading tests. The Student's t-test was performed to assess statistically significant differences in bone mineral density (BMD), displacement, the slope of the load-displacement curves, and load to failure. Results: The screw group showed less displacement (loosening) during cyclical loading, which was significant during 300, 500, 600, 700, 800, 900, and 1000 cycles (p < 0.05: other cycles: 0.079 < p < 0.402). Compared with the suture group, the screw group had higher mean ultimate load values (133.6 N, sd 73.5 vs 110.1 N, sd 46.2; p = 0.416). Conclusion: Fixation of the FHL tendon with a tenodesis screw enables a less invasive procedure to be undertaken and shows similar biomechanical behaviour and primary strength compared with fixation using a transosseus suture. Cite this article: Bone Joint J 2018;100-B:1175-81.

Biomechanical stability of tape augmentation for anterior talofibular ligament (ATFL) repair compared to the native ATFL.

PURPOSE: Current methods of anterior talofibular ligament (ATFL) reconstruction fail to restore the stability of the native ATFL. Therefore, augmented anatomic ATFL reconstruction gained popularity in patients with attenuated tissue and additional stress on the lateral ankle ligament complex. The aim of the present study was to evaluate the biomechanical stability of the InternalBrace (Arthrex Inc., Naples, FL, USA), a tape augmentation designed to augment the traditional Broström procedure. METHODS: Twelve (12) fresh-frozen human anatomic lower leg specimens were randomized into two groups: a native ATFL (ATFL) and a tape augmentation group (IB). Dual-energy X-ray absorptiometry (DEXA) scans were carried out to determine bone mineral density (BMD) of the specimens. The ligaments were stressed by internally rotating the tibia against the inverted fixated hindfoot. Torque at failure (Nm) and angle at failure (°) were recorded. RESULTS: The ATFL group failed at an angle of 33 ± 10°. In the IB group, construct failure occurred at an angle of 46 ± 16°. Failure torque reached 8.3 ± 4.5 Nm in the ATFL group, whereas the IB group achieved 11.2 ± 7.1 Nm. There was no correlation between angle at ATFL or IB construct failure or torque at failure, respectively, and BMD for both groups. CONCLUSION: This study reveals that tape augmentation for ATFL reconstruction shows similar biomechanical stability compared to an intact native ATFL in terms of torque at failure and angle at failure. BMD did not influence the construct stability. Tape augmentation proved an enhanced initial stability in ATFL reconstruction which may allow for an accelerated rehabilitation process. LEVEL OF EVIDENCE: II.

Comparison of Broström technique, suture anchor repair, and tape augmentation for reconstruction of the anterior talofibular ligament.

PURPOSE: Recently, tape augmentation for Broström repair has been introduced in order to improve the primary stability of the reconstructed anterior talofibular ligament (ATFL). The biomechanical effect of tape augmentation suture anchor (SA) repair is not known yet. The aim of the present study was to compare construct stability of the traditional Broström (TB) repair compared with a stand alone SA repair (SutureTak, Arthrex) and SA repair combined with tape augmentation (InternalBrace, Arthrex) internal brace (IB) of the ATFL. METHODS: Eighteen fresh-frozen human anatomic lower leg specimens were randomly assigned to three different groups: TB group, SA group, and IB augmentation group. In vivo torsion conditions in ankle sprain were carried out quasi-statically (0.5°/s). Torque (Nm) required to resist as well as the rotary displacement (°) of the load frame was recorded. Intergroup differences for age, bone mineral density (BMD), angle at failure, and torque at failure were analysed using ANOVA. RESULTS: In the TB group, ATFL reconstruction failed at an angle of 24.1°, in the SA group failure occurred at 35.5°, and in the IB group it failed at 46.9° (p = 0.02). Torque at failure reached 5.7 Nm for the TB repair, 8.0 Nm for the SA repair, and 11.2 Nm for the IB group (p = 0.04). There was no correlation between angle at ATFL failure, torque at failure, and BMD for the SA or IB groups. CONCLUSION: The present biomechanical study reveals statistically superior performance in terms of angle at failure as well as failure torque for the IB group compared to the other reconstruction methods. BMD did not influence the construct stability in the SA repair groups.