Thermal evaluation of plant biomass from the phytostabilisation of soils contaminated by potentially toxic elements.

The combination of phytoremediation of soils contaminated by potentially toxic elements with energy production by combustion of the generated biomass can be a sustainable land management option, combining the production of renewable bioenergy with soil restoration while minimising energy consumption and CO2 emission. In this work, plant biomass from phytoremediation of soils contaminated by potentially toxic elements was studied as solid biofuel for combustion by thermal analysis and biomass composition. Six plant species were grown in two soils with differing degrees of contamination: Brassica juncea, Cynara cardunculus, Atriplex halimus, Nicotiana glauca, Dittrichia viscosa, Retama sphaerocarpa and Salvia rosmarinus. The composition of the plant biomass was characterised chemically and thermogravimetric analyses were performed for the mass loss (TG), derivative curves of mass loss (DTG) and temperature difference (DTA) signal. The cellulose concentration correlated with the parameters of the thermal analysis in the low temperature range (150-350 °C), while lignin correlated with the thermal parameters of the second peak in the high temperature range. Salvia rosmarinus and R. sphaerocarpa showed the best combustion characteristics according to the thermal profile and mineral residue results. The accumulation of potentially toxic elements in B. juncea grown in heavily contaminated soil led to a higher amount of residue at 750 °C, with a global activation energy lower than the one obtained when this species was grown in a soil with lower contamination. Therefore, the most beneficial combination of soil phytoremediation and energy production (combustion) that can be suggested would depend on the level of soil contamination: in heavily contaminated soil, phytostabilisation using R. sphaerocarpa and S. rosmarinus; in slightly contaminated soil, B. juncea due to its high energy of activation, although the concentrations of potentially toxic elements in the residue must be controlled, as well as possible particulate matter emissions during combustion.

Revealing photonic symmetry-protected modes by the finite-difference-time-domain method.

This Letter is devoted to pointing out a specific feature of the finite-difference-time-domain (FDTD) method through the study of nano-structures supporting geometrical symmetry-protected modes that cannot be excited at certain conditions of illumination. The spatial discretization performed in the FDTD algorithm naturally leads to breaking this symmetry and allows the excitation of these modes. The quality factors of the corresponding resonances are then directly linked to the degree of symmetry breaking, i.e., the spatial grid dimension, even though the convergence criteria of the FDTD are fulfilled. This finding shows that the FDTD must be handled with great care and, more importantly, that very huge quality-factor resonances can be achieved at the cost of nanometer-scale mastered fabrication processes.

Selection of Mediterranean plants biomass for the composting of pig slurry solids based on the heat production during aerobic degradation.

Heat recovery from composting processes and its use as a source of bioenergy have come into prominence in recent years. In this study, the selection of an adequate bulking agent for the composting of the solid fraction of pig slurry has been based on the heat produced by the microbial activity during aerobic degradation of the organic matter. Residues of five plant species typical of the Mediterranean area were mixed with the solid fraction of pig slurry, as bulking agents. The residues were: the prunings of three common cultivated tree species (orange, palm, and olive) and the biomass of two herbaceous species (milk thistle and sunflower). Self-heating tests were run for 18 days in thermally insulated laboratory-scale reactors; the energy released as heat was calculated from the temperature increase inside the reactors. The mixtures were sampled at the beginning and end of the experiment, and the microbial stability was evaluated by aerobic respiration tests. The heat energy produced was highest in the mixture with milk thistle (18.3 ± 1.78 MJ kg-1 of total solids -TS), followed by that with orange tree prunings (16.0 ± 1.094 MJ kg-1 TS), and was lowest with olive tree prunings (6.3 ± 0.23 MJ kg-1 TS). The microbial biodegradability of the mixtures and the physico-chemical characteristics (mainly the C/N ratio, cellulose concentration, and density) of the different bulking agents controlled the heat energy produced. The orange tree prunings were considered the most suitable bulking agent for composting of pig slurry solids as they showed high degradability and energy recovery potential.

Effect of initial material bulk density and easily-degraded organic matter content on temperature changes during composting of cucumber stalk.

To inactivate the potentially pathogenic microorganisms and safely utilize vegetable waste compost, ultra-high temperatures (>70°C) should be maintained during the composting without having an inhibitory effect on maturity. This study investigated the influence of bulk density (part 1) and easily-degraded organic matter content (EDOMC, part 2) on temperature evolution during vegetable waste composting: Part 1: corn straw with different particle sizes was used to achieve different bulk densities in the composting material (BD1-BD3); Part 2: partial or total substitution of the corn straw by corn starch was carried out to obtain different EDOMC (ED1-ED4). The composting experiments were conducted in a lab-scale reactor (1.75kg material) and lasted for 30d. Temperature and CO2 emission were recorded daily, and the organic matter, lignocellulose, microbial activity, germination index (GI) and C/N of the samples were measured at different stages. The highest temperature (65.7°C) in part 1 occurred in the treatment with the bulk density of 0.35g/cm3, which also had the longest thermophilic phase. Bulk density was found to seriously influence the utilization efficiency of O2 and heat transfer through materials, rather than heat production from organic matter degradation. In experiment part 2, the highest temperature was obtained with EDOMC of 45% (71.4°C). Therefore, adjusting the bulk density to 0.35g/cm3 and the easily-degraded organic matter content of the initial material to 45% was the best combination for reaching temperatures above 70°C during composting, with no inhibitory effect on the maturity of the compost product.

Bloch surface waves at the telecommunication wavelength with lithium niobate as the top layer for integrated optics.

Lithium niobate (LN)-based devices are widely used in integrated and nonlinear optics. This material is robust and resistive to high temperatures, which makes the LN-based devices stable, but challenging to fabricate. In this work, we report on the design, manufacturing, and characterization of engineered dielectric media with thin-film LN (TFLN) on top for the coupling and propagation of electromagnetic surface waves at telecommunication wavelengths. The designed one-dimensional photonic crystal (1DPhC) sustains Bloch surface waves (BSWs) at the multilayer-air interface at 1550 nm wavelength with a propagation detected over a distance of 3 mm. The working wavelength and improved BSW propagation parameters open the way for exploration of nonlinear properties of BSW-based devices. It is also expected that these novel devices potentially would be able to modify BSW propagation and coupling by external thermal-electrical stimuli due to the improved quality of the TFLN top layer of 1DPhC.

Magnetic spin-orbit interaction of light.

We study the directional excitation of optical surface waves controlled by the magnetic field of light. We theoretically predict that a spinning magnetic dipole develops a tunable unidirectional coupling of light to transverse electric (TE) polarized Bloch surface waves (BSWs). Experimentally, we show that the helicity of light projected onto a subwavelength groove milled into the top layer of a 1D photonic crystal (PC) controls the power distribution between two TE-polarized BSWs excited on both sides of the groove. Such a phenomenon is shown to be solely mediated by the helicity of the magnetic optical field, thus revealing a magnetic spin-orbit interaction of light. Remarkably, this magnetic optical effect is clearly observed via a near-field coupler governed by an electric dipole moment: it is of the same order of magnitude as the electric optical effects involved in the coupling. This opens up new degrees of freedom for the manipulation of light and offers desirable and novel opportunities for the development of integrated optical functionalities.

Polarization controlled directional propagation of Bloch surface wave.

Bloch surface waves (BSWs) are recently developing alternative to surface plasmon polaritons (SPPs). Due to dramatically enhanced propagation distance and strong field confinement these surface states can be successfully used in on-chip all-optical integrated devices of increased complexity. In this work we propose a highly miniaturized grating based BSW coupler which is gathering launching and directional switching functionalities in a single element. This device allows to control with polarization the propagation direction of Bloch surface waves at subwavelength scale, thus impacting a large panel of domains such as optical circuitry, function design, quantum optics, etc.

Tunable Bloch surface waves in anisotropic photonic crystals based on lithium niobate thin films.

We present an original type of one-dimensional photonic crystal that includes one anisotropic layer made of a lithium niobate thin film. We demonstrate the versatility of such a device sustaining different Bloch surface waves (BSWs), depending on the orientation of the incident wave. By varying the orientation of the illumination of the multilayer, we measured an angle variation of 7° between the BSWs corresponding to the extraordinary and the ordinary index of the lithium niobate thin film. The potential of such a platform opens the way to novel tunable and active planar optics based on the electro- and thermo-optical properties of lithium niobate.

Simple production of membrane-based LiNbO3 micro-modulators with integrated tapers.

We report on free-standing electro-optical LiNbO3 waveguides with integrated tapers made by optical grade dicing. Membranes with a calibrated thickness are produced simultaneously with tapers acting as spot-size converters. Thereby, thicknesses from 450 to 500 µm can simply be achieved together with integrated tapers guaranteeing low insertion losses. These developments open the way to the low-cost production of compact and low-power-consuming electro-optical components. As an example, a 200 µm-long free-standing electro-optical Fabry-Perot is demonstrated with a figure of merit of only 0.19 V·cm in a 4.5 µm-thick membrane.

Guided resonances on lithium niobate for extremely small electric field detection investigated by accurate sensitivity analysis.

We present a theoretical study of guided resonances (GR) on a thin film lithium niobate rectangular lattice photonic crystal by band diagram calculations and 3D Finite Difference Time Domain (FDTD) transmission investigations which cover a broad range of parameters. A photonic crystal with an active zone as small as 13µm×13µm×0.7µm can be easily designed to obtain a resonance Q value in the order of 1000. These resonances are then employed in electric field (E-field) sensing applications exploiting the electro optic (EO) effect of lithium niobate. A local field factor that is calculated locally for each FDTD cell is proposed to accurately estimate the sensitivity of GR based E-field sensor. The local field factor allows well agreement between simulations and reported experimental data therefore providing a valuable method in optimizing the GR structure to obtain high sensitivities. When these resonances are associated with sub-picometer optical spectrum analyzer and high field enhancement antenna design, an E-field probe with a sensitivity of 50 µV/m could be achieved. The results of our simulations could be also exploited in other EO based applications such as EEG (Electroencephalography) or ECG (Electrocardiography) probe and E-field frequency detector with an 'invisible' probe to the field being detected etc.

Alleviation of environmental risks associated with severely contaminated mine tailings using amendments: Modeling of trace element speciation, solubility, and plant accumulation.

Tailings are considered one of the most relevant sources of contamination associated with mining activities. Phytostabilization of mine spoils may need the application of the adequate combination of amendments to facilitate plant establishment and reduce their environmental impact. Two pot experiments were set up to assess the capability of 2 inorganic materials (calcium carbonate and a red mud derivate, ViroBindTM ), alone or in combination with organic amendments, for the stabilization of highly acidic trace element-contaminated mine tailings using Atriplex halimus. The effects of the treatments on tailings and porewater physico-chemical properties and trace-element accumulation by the plants, as well as the processes governing trace elements speciation and solubility in soil solution and their bioavailability were modeled. The application of the amendments increased tailings pH and decreased (>99%) trace elements solubility in porewater, but also changed the speciation of soluble Cd, Cu, and Pb. All the treatments made A. halimus growth in the tailings possible; organic amendments increased plant biomass and nutritional status, and reduced trace-element accumulation in the plants. Tailings amendments modified trace-element speciation in porewater (favoring the formation of chlorides and/or organo-metallic forms) and their solubility and plant uptake, which were found to be mainly governed by tailing/porewater pH, electrical conductivity, and organic carbon content, as well as soluble/available trace-element concentrations. Environ Toxicol Chem 2016;35:2874-2884. © 2016 SETAC.

Fano resonance-based highly sensitive, compact temperature sensor on thin film lithium niobate.

In this Letter, we report a Fano resonance-based highly sensitive and compact temperature sensor fabricated on thin film lithium niobate (TFLN) Suzuki phase lattice (SPL) photonic crystal. The experimental sensitivity is estimated to be 0.77 nm/°C with a photonic crystal size of only 25 µm × 24 µm. This sensitivity is 38 times larger than the intrinsic one of lithium niobate which is 0.02 nm/°C. The demonstrated sharp and high extinction ratio characteristics of the Fano lineshape resonance could be an excellent candidate in developing a high sensitivity temperature sensor, electric field sensor, etc.

Assessment and Treatment of Anxiety in Youth With Autism Spectrum Disorders.

OBJECTIVES: Anxiety is one of the most prevalent co-occurring symptoms in youth with autism spectrum disorder (ASD). The assessment and treatment recommendations proposed here are intended to help primary care providers with the assessment and treatment of anxiety in ASD. METHODS: The Autism Speaks Autism Treatment Network/Autism Intervention Research on Physical Health Anxiety Workgroup, a multidisciplinary team of clinicians and researchers with expertise in ASD, developed the clinical recommendations. The recommendations were based on available scientific evidence regarding anxiety treatments, both in youth with ASD and typically developing youth, and clinical consensus of the workgroup where data were lacking. RESULTS: Assessment of anxiety requires a systematic approach to evaluating symptoms and potential contributing factors across various developmental levels. Treatment recommendations include psychoeducation, coordination of care, and modified cognitive-behavioral therapy, particularly for children and adolescents with high-functioning ASD. Due to the limited evidence base in ASD, medications for anxiety should be prescribed cautiously with close monitoring of potential benefits and side effects. CONCLUSIONS: Assessment and treatment of clinical anxiety in youth with ASD require a standardized approach to improve outcomes for youth with ASD. Although this approach provides a framework for clinicians, clinical judgment is recommended when making decisions about individual patients.

Low-loss LiNbO(3) tapered-ridge waveguides made by optical-grade dicing.

We report on low-loss vertical tapers for efficient coupling between confined LiNbO3 optical ridge waveguides and Single Mode Fibers. 3D-Pseudo-Spectral-Time-Domain calculations and Optical-Coherence-Tomography-based methods are advantageously used for the numerical and experimental study of the tapers. The tapered-section is done simultaneously with the ridge waveguide by means of a circular precision dicing saw, so that the fabrication procedure is achieved in only two steps. The total insertion losses through a 1.6 cm long ridge waveguide are measured to be improved by 3 dB in presence of the taper. These tapered-ridge waveguides open the way to the low-cost production of low-loss phase modulators or resonators.

A systematic review of treatments for anxiety in youth with autism spectrum disorders.

This study systematically examined the efficacy and safety of psychopharmacological and non-psychopharmacological treatments for anxiety in youth with autism spectrum disorders (ASD). Four psychopharmacological, nine cognitive behavioral therapy (CBT), and two alternative treatment studies met inclusion criteria. Psychopharmacological studies were descriptive or open label, sometimes did not specify the anxiety phenotype, and reported behavioral activation. Citalopram and buspirone yielded some improvement, whereas fluvoxamine did not. Non-psychopharmacological studies were mainly randomized controlled trials (RCTs) with CBT demonstrating moderate efficacy for anxiety disorders in youth with high functioning ASD. Deep pressure and neurofeedback provided some benefit. All studies were short-term and included small sample sizes. Large scale and long term RCTs examining psychopharmacological and non-psychopharmacological treatments are sorely needed.

Optical characterization of ultra-short Bragg grating on lithium niobate ridge waveguide.

In this Letter, we report a technique to etch giant aspect ratio nanostructures in lithium niobate. An 8 µm long Bragg grating on a Ti:LiNbO3 ridge waveguide was fabricated by combining optical-grade dicing and focused ion beam milling. The reflectivity was evaluated using an optical coherence tomography system: it is measured to be 53% for the TM wave and 47% for the TE wave. We study by 2D-FDTD the modeled behavior of the electromagnetic field when an angle exists between two consecutive sidewalls of the grating in order to understand the difference between ideal Bragg grating and experimental samples. These simulations allow us to optimize the parameters in order to increase the reflection of the grating up to 80%.

Integrated temperature sensor based on an enhanced pyroelectric photonic crystal.

In this paper, temperature variations are detected thanks to an enhanced nano-optical pyroelectric sensor. Sensing is obtained with the pyroelectric effect of lithium niobate (LN) in which, a suitable air-membrane photonic crystal cavity has been fabricated. The wavelength position of the cavity mode is tuned 11.5 nm for a temperature variation of only 32 °C. These results agree quite well with 3D-FDTD simulations that predict tunability of 12.5 nm for 32 °C. This photonic crystal temperature sensor shows a sensitivity of 0.359 nm/°C for an active length of only ~5.2 µm.

Clinical practice pathways for evaluation and medication choice for attention-deficit/hyperactivity disorder symptoms in autism spectrum disorders.

BACKGROUND AND OBJECTIVE: Hyperactivity, impulsivity, and inattention (referred to as "ADHD [attention-deficit/hyperactivity disorder] symptoms") occur in 41% to 78% of children with autism spectrum disorders (ASDs). These symptoms often affect quality of life, interfering with learning or interventions that target primary ASD symptoms. This practice pathway describes the guidelines for evaluation and treatment of children and adolescents with ASD and comorbid ADHD symptoms. METHODS: Current research in this area is limited, and, therefore, these recommendations are based on a systematic literature review and expert consensus in the Autism Speaks Autism Treatment Network Psychopharmacology Committee. RESULTS: The recommended practice pathway includes the Symptom Evaluation Pathway for systematic assessment of ADHD symptoms across settings; examination for comorbid sleep, medical, or psychiatric comorbidities that may contribute to symptoms; and evaluation of behavioral interventions that may ameliorate these symptoms. For children for whom medication is being considered to target the ADHD symptoms, the medication choice pathway provides guidance on the selection of the appropriate agent based on a review of available research, assessment of specific advantages and disadvantages of each agent, and dosing considerations. CONCLUSIONS: These recommendations provide a framework for primary care providers treating children who have ASD and ADHD symptoms. Our systematic review of the current evidence indicates the need for more randomized controlled trials of the medications for ADHD symptoms in ASD. There will also be a need for studies of the effectiveness of these practice pathways in the future.

Determination of local refractive index variations in thin films by heterodyne interferometric scanning near-field optical microscopy.

We report on a heterodyne interferometric scanning near-field optical microscope developed for characterizing, at the nanometric scale, refractive index variations in thin films. An optical lateral resolution of 80 nm (lambda/19) and a precision smaller than 10(-4) on the refractive index difference have been achieved. This setup is suitable for a wide set of thin films, ranging from periodic to heterogeneous samples, and turns out to be a very promising tool for determining the optical homogeneity of thin films developed for nanophotonics applications.

Carbon mineralisation and plant growth in soil amended with compost samples at different degrees of maturity.

The carbon and nitrogen mineralisation of a composting mixture of brewing yeast and lemon tree prunings was studied, at different degrees of stabilisation of this matrix, within an incubation experiment in soil. Meanwhile, a growth test in pots with ryegrass (Lolium perenne L.) was carried out using the selected soil and equal amounts of the composting mixture taken at different maturation steps, in order to evaluate the additions of these organic amendments in terms of fertilising value. Samples of the composting mixture, when poorly transformed through the biostabilisation process, showed high CO2-C releases in the soil, due to the microbial attack on easily degradable organic fractions still present in the mixture, with 24.7% mineralisation of the initial total organic carbon (TOC) after a 70 day incubation. On the other hand, mature compost was the most stable matrix, with only 5.4% of TOC mineralised after 70 days. Furthermore, amendments with the initial composting mixture led to negative net N-mineralisation during 56 days of incubation with soil. Only slight negative values of the net N-mineralisation were detected with fully stabilised compost. Nevertheless, pot experiments with ryegrass revealed that mature compost may promote N mineralisation to certain extents. Moreover, mature compost did not produce any phytotoxic effect, behaving as a slow-action organic fertiliser with N made available through a progressive mineralisation. Thus, the results gained through this study are a confirmation that the fertilising quality of a compost destined for agricultural uses is heavily affected by the complete exhaustion of the maturation reactions.