Effect of Biohythane Production from Distillery Spent Wash with Addition of Landfill Leachate and Sewage Wastewater.

Rapid development of the industrial and domestic sectors has led to the rise of several energy and environmental issues. In accordance with sustainable development and waste minimization issues, biohydrogen production along with biomethane production via two-stage fermentation process using microorganisms from renewable sources has received considerable attention. In the present study, biohythane production with simultaneous wastewater treatment was studied in a two-stage (Biohydrogen and Biomethane) fermentation process under anaerobic conditions. Optimization of high organic content (COD) distillery spent wash effluent (DSPW) with dilution using sewage wastewater was carried out. Addition of leachate as a nutrient source was also studied for effective biohythane production. The experimental results showed that the maximum biohythane production at optimized concentration (substrate concentration of 60 g/L with 30% of leachate as a nutrient source) was 67 mmol/L bio-H2 and with bio-CH4 production of 42 mmol/L. Graphical Abstract.

Bio oil production from microalgae via hydrothermal liquefaction technology under subcritical water conditions.

The upsurge in the concerning issues like global warming, environmental pollution and depletion of fossil fuel resources led to the thrust on third generation biofuels. Algal research has gained a lot of importance in the recent years. Effective utilization of algal biomass in a single step is necessary as it can produce Bio-oil (BO), gases and in addition to a variety of valuable products, along with nutrient recovery. Hydrothermal liquefaction technology does not require the energy intensive drying steps and is an attractive approach for the conversion of algae to liquid fuels. This study investigates direct hydrothermal liquefaction (HTL) of microalgae (Algal biomass) to produce bio-oil using a high-pressure batch reactor under subcritical water conditions. Three different micro algae samples namely, Chlorella vulgaris, Botryococcus braunii and Scenedesmus quadricauda have been examined under hydrothermal liquefaction with different water concentrations (1:6, 1:7, 1:8, 1:9 & 1:10 ratio) at certain temperature range (200-320 °C), pressure (60 bars) and reaction time (30 min). Through liquefaction, the highest BO yield achieved with S. quadricauda was 18 wt% at 1:9 ratio. The chemical components of the obtained bio-oil were analyzed via gas chromatography and the results indicated that the algal BO was composed of furan, phenol, acid, and ester derivatives. Moreover, it was found that by increasing the temperatures, the BO yields increased. This was due to the polymerization reactions that converted the small biomass components into heavier molecules. FTIR spectra showed high percentage of Aliphatic, Phenolic, alcoholic, Carboxylic and Hydroxyl groups for solid residues.

Preparation and characterization of green bricks using pharmaceutical industrial wastes.

This paper reports on recycling of industrial wastes (three pharmaceutical industrial sludges) into environmental friendly value-added materials. Stabilization/Solidification (S/S or bricks) process was applied to make a safer way for the utilization of pharmaceutical waste. The additives in this study include binders (cement, lime and bentonite) and strengthening material (pulverized fuel ash (PFA), silica fume and quarry dust) was used at different compositions. Bricks were cured for 28 days, and the following analysis-like compressive strength, leachability of heavy metals, mineralogical phase identity by X-ray diffraction (XRD) spectroscopy, Fourier transform infrared spectroscopy (FTIR) and thermal behaviour by thermogravimetric-differential thermal analysis (TG-DTA) had done. All the bricks were observed to achieve the standard compressive strength as required for construction according to BIS standards. Metal concentration in the leachate has reached the dischargeable limits according to Brazilian standards. Results of this study demonstrate that production of bricks is a promising and achievable productive use of pharmaceutical sludge.

Effect of operational parameters on heavy metal removal by electrocoagulation.

In the present paper, the performance of electrocoagulation (EC) for the treatability of mixed metals (chromium (Cr), copper (Cu), lead (Pb), nickel (Ni), and zinc (Zn)) from metal plating industrial wastewater (EPW) has been investigated. The study mainly focused on the affecting parameters of EC process, such as electrode material, initial pH, distance between electrodes, electrode size, and applied voltage. The pH 8 is observed to be the best for metal removal. Fe-Fe electrode pair with 1-cm inter-electrode distance and electrode surface area of 40 cm(2) at an applied voltage of 8 V is observed to more efficient in the metal removal. Experiments have shown that the maximum removal percentage of the metals like Cr, Ni, Zn, Cu, and Pb are reported to be 96.2, 96.4, 99.9, 98, and 99.5 %, respectively, at a reaction time of 30 min. Under optimum conditions, the energy consumption is observed to be 51.40 kWh/m(3). The method is observed to be very effective in the removal of metals from electroplating effluent.

Field test results of the motherhood method to measure maternal mortality.

BACKGROUND & OBJECTIVES: Measuring maternal mortality in developing countries poses a major challenge. In Nepal, vital registration is extremely deficient. Currently available methods to measure maternal mortality, such as the sisterhood method, pose problems with respect to validity, precision, cost and time. We conducted this field study to test a community-based method (the motherhood method), to measure maternal and child mortality in a developing country setting. METHODS: Motherhood method was field tested to derive measures of maternal and child mortality at the district and sub-regional levels in Bara district, Nepal. Information on birth, death, risk factors and health outcomes was collected within a geographic area as in an unbiased census, but without visiting every household. The sources of information were a vaccination registry, focus group discussions with local health workers, and most importantly, interview in group setting with women who share social bonds formed by motherhood and aided by their peer memory. Such groups included all women who have given birth, including those whose babies died during the measurement period. RESULTS: A total of 15,161 births were elicited in the study period of two years. In the same period 49 maternal deaths, 713 infant deaths, 493 neonatal deaths and 679 perinatal deaths were also recorded. The maternal mortality ratio was 329 (95%CI: 243-434)/100,000 live birth, infant mortality rate was 48 (44-51)/1000LB, neonatal mortality rate was 33 (30-36)/1000LB, and perinatal mortality rate was 45 (42-48)/1000 total birth. INTERPRETATION & CONCLUSIONS: The motherhood method estimated maternal, perinatal, neonatal and infant mortality rates and ratios. It has been field tested and validated against census data, and found to be efficient in terms of time and cost. Motherhood method can be applied in a time and cost-efficient manner to measure and monitor the progress in the reduction of maternal and child deaths. It can give current estimates of mortalities as well as averages over the past few years. It appears to be particularly well-suited to measuring and monitoring programmes in community and districts levels.