RESUMO
Organic field-effect transistors (OFETs) were fabricated using three high-surface area and flexible expanded-poly(tetrafluoroethylene) (ePTFE) membranes in gate dielectrics, along with the semiconducting polymer poly[2,5-bis(2-octyldodecyl)pyrrolo[3,4-c]pyrrole-1,4(2H,5H)-dione-3,6-diyl)-alt-(2,2':5',2â³:5â³,2â´-quaterthiophen-5,5â´-diyl)] (PDPP4T). The transistor behavior of these devices was investigated following annealing at 50, 100, 150, and 200 °C, all sustained for 1 h. For annealing temperatures above 50 °C, the OFETs displayed improved transistor behavior and a significant increase in output current while maintaining similar magnitudes of Vth shifts when subjected to static voltage compared to those kept at ambient temperature. We also tested the response to NO2 gas for further characterization and for possible applications. The ePTFE-PDPP4T interface of each membrane was characterized via scanning electron microscopy for all four annealing temperatures to derive a model for the hole mobility of the ePTFE-PDPP4T OFETs that accounts for the microporous structure of the ePTFE and consequently adjusts the channel width of the OFET. Using this model, a maximum hole mobility of 1.8 ± 1.0 cm2/V s was calculated for the polymer in an ePTFE-PDPP4T OFET annealed at 200 °C, whereas a PDPP4T OFET using only the native silicon wafer oxide as a gate dielectric exhibited a hole mobility of just 0.09 ± 0.03 cm2/V s at the same annealing condition. This work demonstrates that responsive semiconducting polymer films can be deposited on nominally nonwetting and extremely bendable membranes, and the charge carrier mobility can be significantly increased compared to their as-prepared state by using thermally durable polymer membranes with unique microstructures as gate dielectrics.
RESUMO
Plastic pollution is one of the most pressing global environmental issues we face today, in part due to the continued rise in production and use of disposable plastic products. Polyolefins and polyesters are two of the most prevalent polymers in the world accounting for â¼80% of total nonfiber plastic production. Recycling, despite being intrinsically environmentally friendly and sometimes economically viable, remains at a surprisingly low level (<9% in the U.S.) with most plastic waste ending up in landfills. One reason for this low rate of recycling stems from the challenge of recycling mixed waste streams and multicomponent plastics. In mixed waste streams, physical presorting of components prior to recycling requires significant effort, which translates to added cost. For multicomponent plastics (e.g., multilayer films such as food wrappers), the individual plastic components cannot be efficiently physically separated, and they are immiscible with poor interfacial adhesion when melt reprocessed. Thus, direct recycling of mixed plastics by melt reprocessing results in products that lack desired end-use properties. In this study, we describe the synthesis of novel poly(ethylene terephthalate)-polyethylene multiblock copolymers (PET-PE MBCPs) and evaluate their utility as adhesive tie layers in multilayer films and compatibilizer additives for melt reprocessed blends. PET and PE are targeted because they are two of the most prevalent commercial polymers in the world and are high volume waste streams. The work described here demonstrates two key findings. First, the PET-PE MBCPs serve as effective adhesive tie layers between neat PET/PE films with adhesive strength comparable to that of commercially available adhesives. Second, PET/PE (80/20 wt %) blends containing â¼0.5 wt % PET-PE MBCP were melt mixed to mimic recycling mixed plastic waste, and they were found to exhibit mechanical properties better than neat PET. Overall, this study demonstrates that PET-PE MBCPs could significantly enhance the ability to recycle PET/PE mixed waste streams by serving the role as both an adhesive promoting layer and a compatibilizer additive.
