Utility of cement injection to stabilize split-depression tibial plateau fracture by minimally invasive methods: A finite element analysis.

BACKGROUND: Treatment for fractures of the tibial plateau is in most cases carried out by stable fixation in order to allow early mobilization. Minimally invasive technologies such as tibioplasty or stabilization by locking plate, bone augmentation and cement filling (CF) have recently been used to treat this type of fracture. The aim of this paper was to determine the mechanical behavior of the tibial plateau by numerically modeling and by quantifying the mechanical effects on the tibia mechanical properties from injury healing. METHODS: A personalized Finite Element (FE) model of the tibial plateau from a clinical case has been developed to analyze stress distribution in the tibial plateau stabilized by balloon osteoplasty and to determine the influence of the cement injected. Stress analysis was performed for different stages after surgery. FINDINGS: Just after surgery, the maximum von Mises stresses obtained for the fractured tibia treated with and without CF were 134.9 MPa and 289.9 MPa respectively on the plate. Stress distribution showed an increase of values in the trabecular bone in the treated model with locking plate and CF and stress reduction in the cortical bone in the model treated with locking plate only. INTERPRETATION: The computed results of stresses or displacements of the fractured models show that the cement filling of the tibial depression fracture may increase implant stability, and decrease the loss of depression reduction, while the presence of the cement in the healed model renders the load distribution uniform.

Development of an experimental model of burst fracture with damage characterization of the vertebral bodies under dynamic conditions.

BACKGROUND: Burst fractures represent a significant proportion of fractures of the thoracolumbar junction. The recent advent of minimally invasive techniques has revolutionized the surgical treatment of this type of fracture. However mechanical behaviour and primary stability offered by these solutions have to be proved from experimental validation tests on cadaveric specimens. Therefore, the aim of this study was to develop an original and reproducible model of burst fracture under dynamic impact. METHODS: Experimental tests were performed on 24 cadaveric spine segments (T11-L3). A system of dynamic loading was developed using a modified Charpy pendulum. The mechanical response of the segments (strain measurement on vertebrae and discs) was obtained during the impact by using an optical method with a high-speed camera. The production of burst fracture was validated by an analysis of the segments by X-ray tomography. FINDINGS: Burst fracture was systematically produced on L1 for each specimen. Strain analysis during impact highlighted the large deformation of L1 due to the fracture and small strains in adjacent vertebrae. The mean reduction of the vertebral body of L1 assessed for all the specimens was around 15%. No damage was observed in adjacent discs or vertebrae. INTERPRETATION: With this new, reliable and replicable procedure for production and biomechanical analysis of burst fractures, comparison of different types of stabilization systems can be envisaged. The loading system was designed so as to be able to produce loads leading to other types of fractures and to provide data to validate finite element modelling.

A novel approach for biomechanical spine analysis: Mechanical response of vertebral bone augmentation by kyphoplasty to stabilise thoracolumbar burst fractures.

Kyphoplasty has been shown as a well-established technique for spinal injuries. This technique allows a vertebral bone augmentation with a reduction of morbidity and does not involve any adjacent segment immobilisation. There is a lack of biomechanical information resulting in major gaps of knowledge such as: the evaluation of the "quality" of stabilisation provided by kyphoplasty as a standalone procedure in case of unstable fracture. Our objective is to analyse biomechanical response of spine segments stabilised by Kyphoplasty and PMMA cement after experiencing burst fractures. Six fresh-frozen cadaveric spine specimens constituted by five vertebra (T11-L3) and four disks were tested. A specific loading setup has been developed to impose pure moments corresponding to loadings of flexion-extension, lateral bending and axial rotation. Tests were performed on each specimen in an intact state and post kyphoplasty following a burst fracture. Strain measurements and motion variations of spinal unit are measured by a 3D optical method. Strain measurements on vertebral bodies after kyphoplasty shows a great primary stabilisation. Comparisons of mobility and angles variations between the intact and post kyphoplasty states do not highlight significant difference. Percutaneous kyphoplasty offers a good primary stability in case of burst fracture. Kinematics analysis during physiological movements shows that this stabilisation solution preserve disk mobility in each adjacent spinal unit.

Three-dimensional shape reconstruction by phase-shifting shadow moire.

Shadow moiré shows contour lines of an object with respect to a master grating plane; they result from the interference between the lines of the master grid and their shadow projected by a point source of light. In best cases the sensitivity of this procedure is a few tenths of a millimeter. The introduction of a phase-shifting procedure gives a better resolution, but the problem in practice is how can we shift the phase of the interferogram into shadow moiré? A complete study is presented showing the influence of different parameters. It is shown that only one possibility is available. Some applications to threedimensional shape reconstructions are presented with an accuracy of 0.01 mm, showing that the potentiality of shadow moiré is greatly improved.