Indoor heat exposure in Baltimore: does outdoor temperature matter?

Heat exposure of a population is often estimated by applying temperatures from outdoor monitoring stations. However, this can lead to exposure misclassification if residents do not live close to the monitoring station and temperature varies over small spatial scales due to land use/built environment variability, or if residents generally spend more time indoors than outdoors. Here, we compare summertime temperatures measured inside 145 homes in low-income households in Baltimore city with temperatures from the National Weather Service weather station in Baltimore. There is a large variation in indoor temperatures, with daily-mean indoor temperatures varying from 10 °C lower to 10 °C higher than outdoor temperatures. Furthermore, there is only a weak association between the indoor and outdoor temperatures across all houses, indicating that the outdoor temperature is not a good predictor of the indoor temperature for the residences sampled. It is shown that much of the variation is due to differences in the availability of air conditioning (AC). Houses with central AC are generally cooler than outdoors (median difference of - 3.4 °C) while those with no AC are generally warmer (median difference of 1.4 °C). For the collection of houses with central or room AC, there is essentially no relationship between indoor and outdoor temperatures, but for the subset of houses with no AC, there is a weak relationship (correlation coefficient of 0.36). The results presented here suggest future epidemiological studies of indoor exposure to heat would benefit from information on the availability of AC within the population.

Domestic exposure to endotoxin and respiratory morbidity in former smokers with COPD.

Indoor air pollution has been linked to adverse chronic obstructive pulmonary disease (COPD) health, but specific causative agents have not yet been identified. We evaluated the role of indoor endotoxin exposure upon respiratory health in former smokers with COPD. Eighty-four adults with moderate to severe COPD were followed longitudinally and indoor air and dust samples collected at baseline, 3 and 6 months. Respiratory outcomes were repeatedly assessed at each time point. The associations between endotoxin exposure in air and settled dust and health outcomes were explored using generalizing estimating equations in multivariate models accounting for confounders. Dust endotoxin concentrations in the main living area were highest in spring and lowest in fall, while airborne endotoxins remained steady across seasons. Airborne and dust endotoxin concentrations were weakly correlated with one another (rs  = +0.24, P = 0.005). Endotoxin concentrations were not significantly associated with respiratory symptoms, rescue medication use, quality of life, or severe exacerbations. In vitro whole-blood assays of the pro-inflammatory capacity of PM10 filters with and without endotoxin depletion demonstrated that the endotoxin component of indoor air pollution was not the primary trigger for interleukin-1ß release. Our findings support that endotoxin is not the major driver in the adverse effects of indoor PM upon COPD morbidity.

Home interventions are effective at decreasing indoor nitrogen dioxide concentrations.

UNLABELLED: Nitrogen dioxide (NO2 ), a by-product of combustion produced by indoor gas appliances such as cooking stoves, is associated with respiratory symptoms in those with obstructive airways disease. We conducted a three-armed randomized trial to evaluate the efficacy of interventions aimed at reducing indoor NO2 concentrations in homes with unvented gas stoves: (i) replacement of existing gas stove with electric stove; (ii) installation of ventilation hood over existing gas stove; and (iii) placement of air purifiers with high-efficiency particulate air (HEPA) and carbon filters. Home inspection and NO2 monitoring were conducted at 1 week pre-intervention and at 1 week and 3 months post-intervention. Stove replacement resulted in a 51% and 42% decrease in median NO2 concentration at 3 months of follow-up in the kitchen and bedroom, respectively (P = 0.01, P = 0.01); air purifier placement resulted in an immediate decrease in median NO2 concentration in the kitchen (27%, P < 0.01) and bedroom (22%, P = 0.02), but at 3 months, a significant reduction was seen only in the kitchen (20%, P = 0.05). NO2 concentrations in the kitchen and bedroom did not significantly change following ventilation hood installation. Replacing unvented gas stoves with electric stoves or placement of air purifiers with HEPA and carbon filters can decrease indoor NO2 concentrations in urban homes. PRACTICAL IMPLICATIONS: Several combustion sources unique to the residential indoor environment, including gas stoves, produce nitrogen dioxide (NO2), and higher NO2 concentrations, are associated with worse respiratory morbidity in people with obstructive lung disease. A handful of studies have modified the indoor environment by replacing unvented gas heaters; this study, to our knowledge, is the first randomized study to target unvented gas stoves. The results of this study show that simple home interventions, including replacement of an unvented gas stove with an electric stove or placement of HEPA air purifiers with carbon filters, can significantly decrease indoor NO2 concentrations.

Dose-response relationships between mouse allergen exposure and asthma morbidity among urban children and adolescents.

Home mouse allergen exposure is associated with asthma morbidity, but little is known about the shape of the dose-response relationship or the relevance of location of exposure within the home. Asthma outcome and allergen exposure data were collected every 3 months for 1 year in 150 urban children with asthma. Participants were stratified by mouse sensitization, and relationships between continuous measures of mouse allergen exposure and outcomes of interest were analyzed. Every tenfold increase in the bed mouse allergen level was associated with an 87% increase in the odds of any asthma-related health care use among mouse-sensitized [Odds Ratio (95% CI): 1.87 (1.21-2.88)], but not non-mouse-sensitized participants. Similar relationships were observed for emergency department visit and unscheduled doctor visit among mouse-sensitized participants. Kitchen floor and bedroom air mouse allergen concentrations were also associated with greater odds of asthma-related healthcare utilization; however, the magnitude of the association was less than that observed for bed mouse allergen concentrations. In this population of urban children with asthma, there is a linear dose-response relationship between mouse allergen concentrations and asthma morbidity among mouse-sensitized asthmatics. Bed and bedroom air mouse allergen exposure compartments may have a greater impact on asthma morbidity than other compartments.

Predictors of airborne endotoxin concentrations in inner city homes.

Few studies have assessed in home factors which contribute to airborne endotoxin concentrations. In 85 inner city Baltimore homes, we found no significant correlation between settled dust and airborne endotoxin concentrations. Certain household activities and characteristics, including frequency of dusting, air conditioner use and type of flooring, explained 36-42% of the variability of airborne concentrations. Measurements of both airborne and settled dust endotoxin concentrations may be needed to fully characterize domestic exposure in epidemiologic investigations.

Secondhand tobacco smoke concentrations in motor vehicles: a pilot study.

CONTEXT: Motor vehicles represent important microenvironments for exposure to secondhand smoke (SHS). While some countries and cities have banned smoking in cars with children present, more data are needed to develop the evidence base on SHS exposure levels in motor vehicles to inform policy and education practices aimed at supporting smoke-free motor vehicles when passengers are present. OBJECTIVE: To assess exposure to secondhand tobacco smoke in motor vehicles using passive airborne nicotine samplers. METHODS: 17 smokers and five non-smokers who commute to and from work in their own vehicle participated. Two passive airborne nicotine samplers were placed in each vehicle for a 24-hour period, one at the front passenger seat headrest and the other in the back seat behind the driver. At the end of the sampling period, airborne nicotine was analysed by gas chromatography. RESULTS: Median (IQR) air nicotine concentrations in smokers' vehicles were 9.6 mug/m(3) (5.3-25.5) compared to non-detectable concentrations in non-smokers' vehicles. After adjustment for vehicle size, window opening, air conditioning and sampling time, there was a 1.96-fold increase (95% CI 1.43 to 2.67) in air nicotine concentrations per cigarette smoked. CONCLUSIONS: Air nicotine concentrations in motor vehicles were much higher than air nicotine concentrations generally measured in public or private indoor places, and even higher than concentrations measured in restaurants and bars. These high levels of exposure to SHS support the need for education measures and legislation that regulate smoking in motor vehicles when passengers, especially children, are present.

Characterization of phagolysosomal simulant fluid for study of beryllium aerosol particle dissolution.

A simulant of phagolysosomal fluid is needed for beryllium particle dissolution research because intraphagolysosomal dissolution is believed to be a necessary step in the cellular immune response associated with development of chronic beryllium disease. Thus, we refined and characterized a potassium hydrogen phthalate (KHP) buffered solution with pH 4.55, termed phagolysosomal simulant fluid (PSF), for use in a static dissolution technique. To characterize the simulant, beryllium dissolution in PSF was compared to dissolution in the J774A.1 murine cell line. The effects of ionic composition, buffer strength, and the presence of the antifungal agent alkylbenzyldimethylammonium chloride (ABDC) on beryllium dissolution in PSF were evaluated. Beryllium dissolution in PSF was not different from dissolution in the J774A.1 murine cell line (p = 0.78) or from dissolution in another simulant having the same pH but different ionic composition (p = 0.73). A buffer concentration of 0.01-M KHP did not appear adequate to maintain pH under all conditions. There was no difference between dissolution in PSF with 0.01-M KHP and 0.02-M KHP (p = 0.12). At 0.04-M KHP, beryllium dissolution was increased relative to 0.02-M KHP (p = 0.02). Use of a 0.02-M KHP buffer concentration in the standard formulation for PSF provided stability in pH without alteration of the dissolution rate. The presence of ABDC did not influence beryllium dissolution in PSF (p = 0.35). PSF appears to be a useful and appropriate model of in vitro beryllium dissolution when using a static dissolution technique. In addition, the critical approach used to evaluate and adjust the composition of PSF may serve as a framework for characterizing PSF to study dissolution of other metal and oxide particles.

Ambient urban Baltimore particulate-induced airway hyperresponsiveness and inflammation in mice.

Airborne particulate matter (PM) is hypothesized to play a role in increases in asthma prevalence, although a causal relationship has yet to be established. To investigate the effects of real-world PM exposure on airway reactivity (AHR) and bronchoalveolar lavage (BAL) cellularity, we exposed naive mice to a single dose (0.5 mg/ mouse) of ambient PM, coal fly ash, or diesel PM. We found that ambient PM exposure induced increases in AHR and BAL cellularity, whereas diesel PM induced significant increases in BAL cellularity, but not AHR. On the other hand, coal fly ash exposure did not elicit significant changes in either of these parameters. We further examined ambient PM-induced temporal changes in AHR, BAL cells, and lung cytokine levels over a 2-wk period. Ambient PM-induced AHR was sustained over 7 d. The increase in AHR was preceded by dramatic increases in BAL eosinophils, whereas a decline in AHR was associated with increases in macrophages. A Th2 cytokine pattern (IL-5, IL-13, eotaxin) was observed early on with a shift toward a Th1 pattern (IFN-gamma). In additional studies, we found that the active component(s) of ambient PM are not water-soluble and that ambient PM-induced AHR and inflammation are dose- dependent. We conclude that ambient PM can induce asthma-like parameters in naive mice, suggesting that PM exposure may be an important factor in increases in asthma prevalence.

Mouthpiece diameter affects deposition efficiency in cast models of the human oral airways.

We examined the effect of altering mouthpiece diameter to 1.5, 2.0, and 2.7 cm on the deposition efficiency of inertial size particles (2, 4, and 8 microm) in adult human oral-pharyngeal-laryngeal (OPL) airway cast models at various inspiratory flow rates (30, 60, 90, and 120 L/min). Deposition efficiency of 2-microm particles was unaffected by changes in mouthpiece diameter at all flow rates. Deposition of 4-microm particles decreased significantly with the 2.0- and 2.7-cm mouthpieces compared to the 1.5 cm mouthpiece at 60, 90, and 120 L/min (p < 0.01). Deposition of 4-microm particles was significantly reduced with the 2.7-cm mouthpiece compared to the 2.0-cm mouthpiece at 90 and 120 L/min (p < 0.05). Deposition efficiency of 8 microm particles decreased significantly with the 2.0- and 2.7-cm mouthpieces compared to the 1.5-cm mouthpiece at 60 L/min (p < 0.05), and with the 2.7-cm mouthpiece compared to the 1.5-cm mouthpiece at 120 L/min (p < 0.05). These results suggest that the effect of mouthpiece diameter varies with particle size, with 2- and 8-microm particles least affected. However, our findings may have important implications for improving the future design of mouthpieces of devices that deliver particles with 4-microm diameters and require inspiratory flow rates of > or = 60 L/min (i.e., DPIs) for adequate drug delivery.

End-user exposures to synthetic vitreous fibers: II. Fabrication and installation fabrication of commercial products.

This article summarizes the results of exposure monitoring conducted during the installation and fabrication of commercial synthetic vitreous fiber (SVF) products. Included in this investigation were fiberglass duct insulation and construction applications (duct board, duct liner, and duct wrap), pipe and vessel insulation, batt insulation for prefabricated homes, and general fiberglass products. Commercial mineral wool products sampled as a part of this investigation included ceiling tiles, building safing, and loose insulation for prefabricated homes. A total of 520 valid air samples were collected as a part of this investigation and were analyzed using gravimetric, phase contrast microscopy (PCM), or scanning electron microscopy (SEM). Airborne fiber-size distributions were also determined for a subset of samples collected for SEM analysis. As a result of the task-based sampling strategy used in this study, sample times reflect exposures over the time the person was actually engaged in SVF-related work activities, and exposure results are therefore presented as task-length averages (TLAs). Thirty-five total dust samples were collected as a part of this investigation, resulting in 14 TLAs ranging from 0.3 to 7.6 mg/m3. A total of 125 PCM-based TLAs were collected, with the mean TLA time for all product and occupation categories ranging from 277 to 443 minutes. The mean PCM-based TLAs for all product/occupations were below 1.0 f/cm3, ranging from 0.04 to 0.68 f/cm3. A total of 116 SEM TLAs were determined. Average SEM-based TLA concentrations were slightly lower than the PCM-based estimates and ranged from <0.01 to 0.16 f/cm3. The geometric mean fiber diameters for commercial products and occupations sampled as a part of the investigation ranged from 0.8 microm to 1.9 microm. Geometric mean fiber length varied by a factor of approximately three, ranging from 9.5 microm to 29.5 microm.

Case-control study of intracranial tumors among employees at a petrochemical research facility.

This case-control study evaluated the relation between potential exposure to chemical and physical agents and the occurrence of intracranial tumors among employees at a petrochemical research facility. Cases were employees with glioma (n = 6) or benign intracranial tumors (n = 6). Controls (n = 119) were individually matched to cases on gender and birth year, and they were alive and did not have an intracranial tumor at the case's diagnosis date. Exposure information came from interviews with subjects or surrogates and from corporate records on agents used in research projects. Analyses computed matched odds ratios (ORs) and corresponding 95% confidence intervals (CIs) for self-reported exposure to 15 agents and project-based estimates of exposure to 29 agents. For gliomas, the OR was elevated for self-reported exposure to ionizing radiation (OR, 15.7; CI, 1.4 to 179.4), n-hexane (OR, infinity; CI, 1.4 to infinity), organometallics (OR, 9.4; CI, 1.5 to 59.7), and amines other than nitrosamines (OR, 6.0; CI, 1.0 to 35.7). The OR also was elevated for project-based potential use of ionizing radiation (OR, 9.6; CI, 1.7 to 55.2) and for potential use of n-hexane lasting at least 4 years (OR, 16.2; CI, 1.1 to 227.6). For benign intracranial tumors, the OR was elevated only for self-reported exposure to ionizing radiation (OR, 5.4; CI, 1.7 to 43.1) and other amines (OR, 5.2; CI, 0.9 to 29.5). Occupational exposure may have contributed to the glioma excess, but the specific causal agents remain unknown. The study indicated that benign intracranial tumors were unlikely to be work-related.

An evaluation of employee exposure to volatile organic compounds in three photocopy centers.

Personal and area samples from three copy centres were collected in thermal desorption tubes and analyzed using gas chromatography-mass spectrometry. Real-time personal total volatile organic compounds (TVOC) were measured using a data-logging photoionization detector. Fifty-four different VOCs were detected in the area samples. The maximum concentration measured was 1132.0 ppb (toluene, copy center 3, day 1). Thirty-eight VOCs were detected in the personal samples and concentrations ranged from 0.1 ppb (1,1-biphenyl, p-dichlorobenzene, propylbenzene, styrene, and tetrachloroethylene) to 689.6 ppb (toluene). Real-time TVOC measurements indicated daily fluctuations in exposure, ranging from <71 to 21,300 ppb. The time-weighted average exposures for the photocopier operators on days 1 and 2 were 235 and 266 ppb and 6155 and 3683 ppb, in copy centers 2 and 3, respectively. Personal exposure measurements of individual VOCs were below accepted occupational standards and guidelines. For example, the maximum concentration was 0.3% of the permissible exposure limits (toluene, copy center 3). Exposures were highest in copy center 3; this is likely due to the presence of offset printing presses. It is concluded that photocopiers contribute a wide variety of VOCs to the indoor air of photocopy centers; however, exposures are at least 100 times below established standards.

Chemical hazards in radiology.

A variety of chemicals are used in medical imaging as developer and fixer ingredients, germicides, and cleaning agents. Glutaraldehyde, a potent sensitizer, may cause occupational skin and respiratory diseases in exposed individuals. Poor ventilation, unsafe practices, and lack of hazard recognition may contribute to occupational asthma and other respiratory disease in susceptible medical imaging personnel. Failure to respond effectively to initial health complaints and reduce exposure levels can have serious consequences for affected employees. It is therefore important for occupational safety and health professionals to alert health facility managers to potential dangers and to recommend effective intervention strategies. When problems are identified, a multidisciplinary team approach is the best method for evaluating and controlling hazards. This team should include industrial hygienists, safety staff, occupational medicine physicians, mechanical and ventilation engineers, personnel specialists, and medical imaging staff. A thorough hazard assessment, medical diagnosis, and administrative personnel actions are critical to effective problem identification and correction. In the case of chemical sensitization, removal of the affected employee may be necessary. By working with designers and equipment installers to monitor compliance with appropriate codes and manufacturers' specifications, hazards can be prevented. We present additional operations, ventilation, and design improvements to reduce chemical exposures to radiology employees.

Carpet properties that affect the retention of cat allergen.

BACKGROUND: Although the importance of carpeting on airborne levels of cat allergen (Fel d 1) has been demonstrated, no studies have been performed to determine specific properties of carpet that may affect its retention and removal. OBJECTIVES: This study characterizes factors that affect the retention of cat allergen on tufted carpets. The experiments were designed to test the hypothesis that the amount of allergen-containing dust recovered from vacuum samples of tufted carpet sources was dependent on micro (fiber) or macro (construction) retention properties of carpets. METHODS: Twenty-six types of custom manufactured carpet were spiked and embedded with reference dust containing Fel d 1. A standardized vacuum surface sampler was used to recover dust from the samples. Allergen was assayed using a standard, monoclonal antibody ELISA. RESULTS: Carpet-surface area and fluorocarbon-fiber treatments were found to have the largest effects on retention and recovery of cat allergen. The style per se of a carpet, such as loop or cut pile, does not affect allergen retention. These results are generally in agreement with previous studies on dust mite allergen retention. CONCLUSIONS: Carpets that are easiest to clean would have the following properties for release of cat allergen and in this order: low pile density and height, fluorocarbon coating of fibers, high denier per filament, and a fiber shape with a low surface area.

Comparison of personal exposure meter placement for the determination of office worker ELF magnetic field exposures.

This article compares extremely low frequency (ELF) magnetic field exposures measured by placing EMDEX Lite personal exposure meters (PEMs) at the head, chest, and waist level for a group of office workers. Twenty-three volunteers were solicited to wear three PEMs simultaneously; one was attached to a baseball cap worn on the head, one was attached to a band and worn around the neck (positioned on the chest), and one was worn in a belted pouch around the waist (positioned on the right side of the hip). The effect of PEM placement was evaluated by comparing full-shift average exposures and daily maximum or peak exposure. The results of this investigation indicate that time-weighted average magnetic field exposures determined at the hip provide the highest mean exposure estimates. Averages of the full-shift mean magnetic field measurements taken at hip and head levels were statistically greater than measurements taken at the chest level by 33 and 22%, respectively. Comparisons of the maximum or peak magnetic field exposures by body position indicate that the hip position produced an average exposure estimate that was 136% greater than the average head-level measurement. Results suggest that for office workers PEM meter placement on the body does not produce large differences in full-shift average ELF magnetic flux density exposures. However, the hip position produced the largest daily maximum or peak exposures. It is recommended that PEMs be placed on the hip for exposure assessments in office environments, because this placement is the most commonly used, the most convenient, and resulted in the highest magnetic field exposures.

Case-series investigation of intracranial neoplasms at a petrochemical research facility.

BACKGROUND: From 1970 through 1997, 17 intracranial neoplasms were identified among 6,800 employees of a petrochemical research facility. This investigation describes the case-series. METHODS: The intracranial neoplasms were identified by self reports and record linkages, and were confirmed by medical records and a pathology review. Standardized incidence ratios (SIRs) compare observed and expected numbers of cases according to certain work characteristics. RESULTS: Overall, there were 17 observed and 10.5 expected intracranial neoplasms, including 11/4.7 benign intracranial tumors and 6/5.9 brain cancers. All brain cancers occurred among male research scientists or technicians. Four had worked at some time on the same floor of one building (SIR=12.6, 95% CI=3.4-32.1), and several had worked on a research project with at least one other brain cancer case. The benign intracranial neoplasm cases did not have common building assignments or work activities. CONCLUSIONS: The occurrence pattern of brain cancers, but not that of benign tumors, suggests a possible occupational etiology.

The environment and asthma in U.S. inner cities.

The prevalence and severity of asthma has increased in the last 20 years, and the greatest increase has been seen among children and young adults living in U.S. inner cities. The reasons for this increase are obviously complex, but include environmental exposures to allergens and pollutants, changing patterns of medication, and the psychosocial stresses of living in poor inner-city neighborhoods. This paper presents an overview of environmental, immunologic, and genetic factors associated with asthma morbidity and mortality. This overview can be used to provide a framework for designing an interdisciplinary research program to address the complexities of asthma etiology and exacerbation. The strongest epidemiologic association has been found between asthma morbidity and the exposure of immunologically sensitive asthmatic patients to airborne allergens. Our current understanding of the process of sensitization suggests that there is a strong genetic predisposition to form IgE to allergenic proteins on airborne particles. Much of this work has been conducted with animal models, but in a number of instances, specific confirmation has been reported in humans. Sensitized individuals respond to inhaled exposure with immediate mast-cell dependent inflammation that may be augmented by pollutant particles, especially diesel exhaust particles. Relatively little is known about the methods of assessing exposure to airborne pollutants, especially biologically active particulates. However, to examine the relationship of morbidity in genetically predisposed individuals, it will be important to determine the most relevant method of making this assessment.

A soiling system for evaluation of house dust, allergens, and lead retention on carpets and other surfaces.

Artificial soiling of carpeted or other floor surfaces has several important applications in human exposure assessment and textile research including evaluation of textile properties, sampling devices, and cleaning regimens. A method was developed and validated to deposit uniform and reproducible known quantities of house dust, allergens, and leaded dust on carpets. The soiling apparatus consisted of a 100 cm x 60 cm inclined steel track and a plastic cylinder, with a series of staggered holes, that contains a known volume of reference house dust. After deposition, the dust is embedded by dragging a steel rod over the carpet surface. Deposition tests were performed with bulk house dust, sodium chloride, and house dust with reference quantities of dust mite allergen and lead. The apparatus deposited equivalent (arithmetic mean) amounts of dust, sodium chloride, and dust mite allergen on the front and back halves of test carpets. The introduction of inert fumed silica to the reference sample aided in dispersal of dust over test surfaces. Little to no variation in mean deposition was found within or between 4 days of testing. Using a grid containing weighing boats under the apparatus, spatial deposition was found to vary across a 92 x 46 cm surface by 13 percent. The apparatus deposited reproducible mean quantities of bulk dust on test surfaces from 7 g/m2 to 28 g/m2 with a coefficient of variation ranging from 4-6 percent. The apparatus could be altered to deliver smaller or larger amounts of dust.

Factors affecting the retention of dust mite allergen on carpet.

Carpeting is one of the most common and perhaps the most important reservoir of aeroallergens and other components of dust found in residential or commercial settings. This research evaluated factors that affect the retention of dust mite allergens on different types of tufted carpet commonly found in homes and offices. Twenty-six types of carpet were custom manufactured as part of a two-stage factorial experiment using 182 carpet samples. Carpets differed with respect to fiber denier, cross-sectional shape, presence of fluorocarbon treatment, carpet style, pile height, and pile density. The major hypothesis tested was that the amount of allergen-containing dust recovered from vacuum samples of tufted carpet sources was dependent on micro (fiber) or macro (construction) retention characteristics of the carpets. Carpet samples were doped in a uniform and reproducible manner using an allergen-containing reference dust. A standardized vacuum surface sampler was used to recover dust from samples. Allergen was assayed using a standard, monoclonal antibody ELISA. Carpet-surface area and presence of fluorocarbon were found to have the largest effects on retention and recovery of dust and allergen. Specifically, fluorocarbon treatment of fibers, square-hollow fiber shape, high-denier fiber, low-pile height in cut-pile carpets, and low-pile density in loop carpets were significantly associated with increased release and recovery of allergen. Results from this study suggest that carpet type be considered for both allergen avoidance and allergy and asthma risk assessment.

Evaluation of integrity of gloves used in a flow cytometry laboratory.

This study was conducted to evaluate the effect of normal use on latex glove integrity in a flow cytometry laboratory. The gloves were tested using the 1,000 microL water-tight test and met industrial standards (less than 4% leakage) before, but not after use. More durable gloves, or more frequent changes of gloves, may be needed to ensure adequate barrier protection for laboratory workers during routine procedures.