Felsic volcanism as a factor driving the end-Permian mass extinction.

The Siberian Traps large igneous province (STLIP) is commonly invoked as the primary driver of global environmental changes that triggered the end-Permian mass extinction (EPME). Here, we explore the contributions of coeval felsic volcanism to end-Permian environmental changes. We report evidence of extreme Cu enrichment in the EPME interval in South China. The enrichment is associated with an increase in the light Cu isotope, melt inclusions rich in copper and sulfides, and Hg concentration spikes. The Cu and Hg elemental and isotopic signatures can be linked to S-rich vapor produced by felsic volcanism. We use these previously unknown geochemical data to estimate volcanic SO2 injections and argue that this volcanism would have produced several degrees of rapid cooling before or coincident with the more protracted global warming. Large-scale eruptions near the South China block synchronous with the EPME strengthen the case that the STLIP may not have been the sole trigger.

Precise Analysis of Gallium Isotopic Composition by MC-ICP-MS.

Though an isotope approach could be beneficial for better understanding the biogeochemical cycle of gallium (Ga), an analogue of the monoisotopic element aluminum (Al), the geochemistry of Ga isotopes has not been widely elaborated. We developed a two-step method for purifying Ga from geological (biological) samples for precise measurement of Ga isotope ratio using multicollector inductively coupled plasma mass spectrometry (MC-ICP-MS). Ga was thoroughly separated from other matrix elements using two chromatographic columns loaded with AG 1-X4 and Ln-spec resin, respectively. The separation method was carefully calibrated using both synthetic and natural samples and validated by assessing the extraction yield (99.8 ± 0.8%, 2SD, n = 23) and the reproducibility (2SD uncertainty better than 0.05‰, n = 116) of the measured isotopic ratio (expressed as δ71Ga). The validation of the whole protocol, together with instrumental analysis, was confirmed by the investigation of the matrix effect, the result of a standard addition experiment, and the comparison of Ga isotope measurement on two mass spectrometers-Nu Plasma II and Neptune Plus. Although the measurements using the sample-standard bracketing (SSB) correction method on both instruments resulted in identical δ71Ga values for reference materials, the modified empirical external normalization (MEEN) method gave relatively better precision compared to SSB on Neptune. Our preliminary results showed large variation of δ71Ga (up to 1.83‰) for 10 standards, with higher values in industrially produced materials, implying potential application of Ga isotopes.

[Influence of the included angle between anterior aspects of S2 and S1 vertebral bodies on pelvic inlet imaging in mid-line sagittal plane].

OBJECTIVE: To analyze the influence of included angle between the anterior aspects of S2 and S vertebral bodies on pelvic inlet imaging in the pelvic midline sagittal plane. METHODS: Totally 58 axial pelvic CT scans were chosen as study objects including 43 males and 15 females,with an average age of 40.7 years old (ranged,18 to 68 years old). The angles between the anterior aspects of S2 and S1, vertebral bodies and the horizontal plane on midline sagittal CT reconstruction were measured to simulate the optimal S2 and S1 inlet angles. The included angle between the anterior aspects of S2 and S1 vertebral bodies was calculated by subtrocting the S1,inlet angle from the S2 inlet angle defined as a base number. Then, the impact of the calculated included angles on the pelvic inlet imaging was analyzed. Results:The S2 inlet angles averaged (30.5±6.5) degrees; the S inlet angles averaged (25.7±5.9) degrees. The difference between them was significant (t=3.35, P=0.001). Ten patients had zero angle between the anterior aspects of S2 and S1 vertebral bodies; 14 patients had negative angle, averaged-(8.9±8.1) degrees; 34 patients had positive angle,averaged (11.8+6.4) degrees. CONCLUSION: The difference of included angle between the anterior aspects of S2 and S1 vertebral bodies leads to the difference between S1 inlet view and S2 inlet view in most cases, complicating the pelvic inlet imaging,and affecting the reliability of the application of pelvic inlet view. Utilizing the angles measured on the preoperative midlihe sagittal CT reconstruction to obatin the patient-customized S1 and S2 inlet views could accurately guide the S1 and S2 iliosacral screw insertion.