Increased flexibility and efficiency of a double-scattering FLASH proton beamline configuration forin vivoSOBP radiotherapy treatments.

Objective. To commission a proton, double-scattering FLASH beamline by maximizing efficiency and field size, enabling higher-linear energy transfer FLASH radiotherapy to cells and small animals using a spread-out Bragg peak (SOBP) treatment configuration. We further aim to provide a configuration guide for the design of future FLASH proton double-scattering (DS) beamlines.Approach. Beam spot size and spread were measured with film and implemented into TOol for PArticle Simulation (TOPAS). Monte Carlo simulations were optimized to verify the ideal positioning, dimensions, and material of scattering foils, secondary scatterers, ridge filters, range compensators, and apertures. A ridge filter with three discrete heights was used to create a spread-out Bragg peak (SOBP) and was experimentally verified using our in-house experimental FLASH beamline. The increase in dose rate was compared to nominal shoot-through techniques.Results. The configuration and scatterer distance producing the largest field size of acceptable flatness, without drastically compromising dose rate was determined to be an elliptical field of 2 cm × 1.5 cm (25% larger than a previous configuration). SOBP testing yielded three distinct but connected spikes in dose with flatness under 5%. Reducing the thickness of the (first) scattering foil by a factor of two was found to increase efficiency by 50%. The new settings increased the field size, provided a Bragg peak treatment option, and increased the maximum available dose rate by 85%, as compared to the previous, shoot through method.Significance. Beam line updates established FLASH dose rates of over 135 Gy s-1(potentially higher) at our double-scattering beamline, increased the efficiency and field size, and enabled SOBP treatments by incorporating an optimized ridge filter. Based on our simulations we provide parametric suggestions when commissioning a new proton DS beamline. This enhanced FLASH beamline for SOBP irradiations with higher dose rates and larger field sizes will enable a wider variety of experimentation in future studies.

Investigation of time-resolved proton radiography using x-ray flat-panel imaging system.

Proton beam therapy benefits from the Bragg peak and delivers highly conformal dose distributions. However, the location of the end-of-range is subject to uncertainties related to the accuracy of the relative proton stopping power estimates and thereby the water-equivalent path length (WEPL) along the beam. To remedy the range uncertainty, an in vivo measurement of the WEPL through the patient, i.e. a proton-range radiograph, is highly desirable. Towards that goal, we have explored a novel method of proton radiography based on the time-resolved dose measured by a flat panel imager (FPI). A 226 MeV pencil beam and a custom-designed range modulator wheel (MW) were used to create a time-varying broad beam. The proton imaging technique used exploits this time dependency by looking at the dose rate at the imager as a function of time. This dose rate function (DRF) has a unique time-varying dose pattern at each depth of penetration. A relatively slow rotation of the MW (0.2 revolutions per second) and a fast image acquisition (30 frames per second, ~33 ms sampling) provided a sufficient temporal resolution for each DRF. Along with the high output of the CsI:Tl scintillator, imaging with pixel binning (2 × 2) generated high signal-to-noise data at a very low radiation dose (~0.1 cGy). Proton radiographs of a head phantom and a Gammex CT calibration phantom were taken with various configurations. The results of the phantom measurements show that the FPI can generate low noise and high spatial resolution proton radiographs. The WEPL values of the CT tissue surrogate inserts show that the measured relative stopping powers are accurate to ~2%. The panel did not show any noticeable radiation damage after the accumulative dose of approximately 3831 cGy. In summary, we have successfully demonstrated a highly practical method of generating proton radiography using an x-ray flat panel imager.

SU-E-T-158: Neutron Damage of Power Electronics Used during Image Guidance in Proton Therapy.

PURPOSE: A series of measurements were performed in a clinical proton therapy beam to assess the sensitivity of silicon-based electronics in commercial x-ray generators to single event burnout from the secondary neutron background in proton therapy treatments. METHODS: Failure rates were nondestructively measured in various metal oxide semiconductor field-effect transistors (MOSFETs) as a function of applied voltage using a dedicated test circuit board. Neutrons were produced by 230 MeV protons stopping in a brass beam target and high beam current was used to accelerate testing. Neutron fluences were measured by activation analysis of carbon and aluminum in both the test setup and in situ at the generator. Failure rates were determined by scaling results based on beam monitor output to the relevant neutron fluence rate. RESULTS: Current pulses from the test board clearly indicated the onset of single event burnout without destroying the MOSFET. The neutron fluence measured on the test board was 4.3 ± 0.8×106 n cm-2 MU-1 and this is consistent with previous measurements. The MOSFET failure rate decreased rapidly with a reduction in the applied voltage and is 20-30 times lower in higher-rated components at the same voltage. Under nominal operating conditions the estimated failure rate is tens of failures per year for a generator 6m from the treatment position. CONCLUSION: The sensitivity of x-ray generator power electronics to neutron-induced single-event burnout is significant and can affect the implementation of image-guided techniques for proton therapy. Strategies and system designs to mitigate this phenomenon are being investigated to help enable x-ray generators withstand the proton therapy environment. This research was supported by the NIH/NCI under grant number 6-PO1 CA 21239.

Water equivalent path length measurement in proton radiotherapy using time resolved diode dosimetry.

PURPOSE: To verify water equivalent path length (WEPL) before treatment in proton radiotherapy using time resolved in vivo diode dosimetry. METHODS: Using a passively scattered range modulated proton beam, the output of a diode driving a fast current-to-voltage amplifier is recorded at a number of depths in a water tank. At each depth, a burst of overlapping single proton pulses is observed. The rms duration of the burst is computed and the resulting data set is fitted with a cubic polynomial. RESULTS: When the diode is subsequently set to an arbitrary depth and the polynomial is used as a calibration curve, the "unknown" depth is determined within 0.3 mm rms. CONCLUSIONS: A diode or a diode array, placed (for instance) in the rectum in conjunction with a rectal balloon, can potentially determine the WEPL at that point, just prior to treatment, with submillimeter accuracy, allowing the beam energy to be adjusted. The associated unwanted dose is about 0.2% of a typical single fraction treatment dose.

Direct absorbed dose to water determination based on water calorimetry in scanning proton beam delivery.

PURPOSE: The aim of this manuscript is to describe the direct measurement of absolute absorbed dose to water in a scanned proton radiotherapy beam using a water calorimeter primary standard. METHODS: The McGill water calorimeter, which has been validated in photon and electron beams as well as in HDR 192Ir brachytherapy, was used to measure the absorbed dose to water in double scattering and scanning proton irradiations. The measurements were made at the Massachusetts General Hospital proton radiotherapy facility. The correction factors in water calorimetry were numerically calculated and various parameters affecting their magnitude and uncertainty were studied. The absorbed dose to water was compared to that obtained using an Exradin T1 Chamber based on the IAEA TRS-398 protocol. RESULTS: The overall 1-sigma uncertainty on absorbed dose to water amounts to 0.4% and 0.6% in scattered and scanned proton water calorimetry, respectively. This compares to an overall uncertainty of 1.9% for currently accepted IAEA TRS-398 reference absorbed dose measurement protocol. The absorbed dose from water calorimetry agrees with the results from TRS-398 well to within 1-sigma uncertainty. CONCLUSIONS: This work demonstrates that a primary absorbed dose standard based on water calorimetry is feasible in scattered and scanned proton beams.

Quantitative assessment of the physical potential of proton beam range verification with PET/CT.

A recent clinical pilot study demonstrated the feasibility of offline PET/CT range verification for proton therapy treatments. In vivo PET measurements are challenged by blood perfusion, variations of tissue compositions, patient motion and image co-registration uncertainties. Besides these biological and treatment specific factors, the accuracy of the method is constrained by the underlying physical processes. This phantom study distinguishes physical factors from other factors, assessing the reproducibility, consistency and sensitivity of the PET/CT range verification method. A spread-out Bragg-peak (SOBP) proton field was delivered to a phantom consisting of poly-methyl methacrylate (PMMA), lung and bone equivalent material slabs. PET data were acquired in listmode at a commercial PET/CT scanner available within 10 min walking distance from the proton therapy unit. The measured PET activity distributions were compared to simulations of the PET signal based on Geant4 and FLUKA Monte Carlo (MC) codes. To test the reproducibility of the measured PET signal, data from two independent measurements at the same geometrical position in the phantom were compared. Furthermore, activation depth profiles within identical material arrangements but at different positions within the irradiation field were compared to test the consistency of the measured PET signal. Finally, activation depth profiles through air/lung, air/bone and lung/bone interfaces parallel as well as at 6 degrees to the beam direction were studied to investigate the sensitivity of the PET/CT range verification method. The reproducibility and the consistency of the measured PET signal were found to be of the same order of magnitude. They determine the physical accuracy of the PET measurement to be about 1 mm. However, range discrepancies up to 2.6 mm between two measurements and range variations up to 2.6 mm within one measurement were found at the beam edge and at the edge of the field of view (FOV) of the PET scanner. PET/CT range verification was found to be able to detect small range modifications in the presence of complex tissue inhomogeneities. This study indicates the physical potential of the PET/CT verification method to detect the full-range characteristic of the delivered dose in the patient.