Adsorption Behaviour of Tween 85 on Nano-Aluminium Particles in Aluminium/JP-10 Suspensions.

A stability analyser and a rheometer were used to study the effects of Tween 85 (polyoxyethylene sorbitan trioleate) on the dispersion properties of nano-aluminium/JP-10 (exo-tetrahydrodicyclopentadiene) suspensions. Results show that the addition of Tween 85 can effectively improve the stability of two-phase suspensions by hindering particle aggregation and reduce the viscosity of a system. The surface characteristics of the zeta potential and the contact angle were measured. The dispersion of the suspensions was improved by Tween 85 mainly by enhancing the steric hindrance of particles. The adsorbed particles obtained in JP-10 with different Tween 85 concentrations were analysed via scanning electron microscopy and Fourier transform infrared spectroscopy to explore the adsorption behaviour of Tween 85 molecules on the surface of aluminium particles and to confirm that Tween 85 formed an adsorption layer on the particle surface. Thermogravimetric analysis indicated that the adsorption amount of Tween 85 increased with its concentration in JP-10. The roughness analysis of the surface of adsorbed particles was measured via atomic force microscopy to characterise the thickness of the adsorption layer. The results showed that Tween 85 molecules formed an irregular adsorption layer on the particle surface, and an increase in the concentration of Tween 85 in JP-10 increased the thickness of the adsorption layer.

Assessment of winter air pollution episodes using long-range transport modeling in Hangzhou, China, during World Internet Conference, 2015.

A winter air pollution episode was observed in Hangzhou, South China, during the Second World Internet Conference, 2015. To study the pollution characteristics and underlying causes, the Weather Research and Forecasting with Chemistry model was used to simulate the spatial and temporal evolution of the pollution episode from December 8 to 19, 2015. In addition to scenario simulations, analysis of the atmospheric trajectory and synoptic weather conditions were also performed. The results demonstrated that control measures implemented during the week preceding the conference reduced the fine particulate matter (PM2.5) pollution level to some extent, with a decline in the total PM2.5 concentration in Hangzhou of 15% (7%-25% daily). Pollutant long-range transport, which occurred due to a southward intrusion of strong cold air driven by the Siberia High, led to severe pollution in Hangzhou on December 15, 2015, accounting for 85% of the PM2.5 concentration. This study provides new insights into the challenge of winter pollution prevention in Hangzhou. For adequate pollution prevention, more regional collaborations should be fostered when creating policies for northern China.

Adsorption of polychlorinated dibenzo-p-dioxins/dibenzofurans on activated carbon from hexane.

Activated carbon is widely used to abate dioxins and dioxin-like compounds from flue gas. Comparing commercial samples regarding their potential to adsorb dioxins may proceed by using test columns, yet it takes many measurements to characterise the retention and breakthrough of dioxins. In this study, commercial activated carbon samples are evaluated during tests to remove trace amounts of dioxins dissolved in n-hexane. The solution was prepared from fly ash collected from a municipal solid waste incinerator. The key variables selected were the concentration of dioxins in n-hexane and the dosage of activated carbon. Both polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) showed very high removal efficiencies (94.7%-98.0% for PCDDs and 99.7%-99.8% for PCDFs). The presence of a large excess of n-hexane solvent had little effect on the removal efficiency of PCDD/Fs. The adsorbed PCDD/Fs showed a linear correlation (R(2) > 0.98) with the initial concentrations. Comparative analysis of adsorption isotherms showed that a linear Henry isotherm fitted better the experimental data (R(2) = 0.99 both for PCDDs and PCDFs) than the more usual Freundlich isotherm (R(2) = 0.88 for PCDDs and 0.77 for PCDFs). Finally, the results of fingerprint analysis indicated that dioxin fingerprint (weight proportion of different congeners) on activated carbon after adsorption did not change from that in hexane.

[The Experimental Research on Reducing the Minimum Measureable Limit of Tunable Diode Laser Absorption Spectroscopy with Wavelet Analysis].

To obtain the weaker second harmonic signal of low concentration, reduce the minimum measurable limit and improve the sensitivity and accuracy of absorption measurement, a serious of data processing methods are proposed based on tunable diode laser wavelength modulation spectroscopy. The experiment on lower NH3 concentration at 2.25 µm was carried out in a 10.13 m absorption cell with different concentration. The peak height of the second harmonic signal is maximum at m=2.2, which optimizes the signal-to-noise ratio. In order to guarantee the optimal signal-to-noise ratio, the experiment was carried out by loading the optimal high frequency modulation signal. WMS-2f was performed at a repetitive scan rate of 200 Hz and a current-modulation rate of 15 kHz, wavelength modulation spectroscopy with the optimal signal-to-noise ratio was adopted for its better noise immunity to measure different lower NH3 concentration in the Herriott cell. This survey is focused on the ν2+ν3 bands of absorption spectra near 2.25 µm in near-infrared region at ambient temperature and pressure, the line strengths of 2.25 µm are much larger than the absorption lines in the telecommunication bands, using stronger NH3 absorption lines can offer the potential of lower detection limits. During the data processing, the background signal of the original harmonic should be deducted at first, the second harmonic signal of 0.6×10-6 was obtained in a 10 m long-path Herriott cell after data processing, these signal processing mainly consist of cross-correlation analysis, multiple averages and wavelet transform analysis, the cross-correlation analysis was used to control the shift of center wavelength, the multiple averages and wavelet transform analysis were used to reduce influences of the environment noise, after that we get the revised second harmonic signal and improve the accuracy of the measurement results. The experimental results show that these data processing methods can obviously improve the signal quality and reduce the minimum measurable limit about 100 times lower than before. The experiment doesn't need to add any laboratory equipment and can well restrain the influence of the environmental noise and other disturbance, so these signal process combined with wavelength modulation technique will be more useful for on-line gas detection technology.

[Research on the Distribution of Gas Concentration of Two-Dimensional Reconstruction Based on Tunable Diode Laser Absorption Spectroscopy with Multispectral Absorption].

The two-dimensional concentration distribution was reconstructed by using algebraic iterative reconstruction algorithm. This paper mainly focused on the effects of multispectral H2O absorptions on condition that the laser beam was less and the temperature was known, i.e. the influence of temperature on spectral line-strength was not considered as to this concentration distribution. Based on ART algorithm, increased spectral lines and increased laser beam were compared under the same concentration model. Three H2O lines were selected to reconstruct two-dimensional distribution of non-uniform gas concentration, and these three transitions were selected within the external cavity diode laser turning range in the simulated system. The interested region was discretized to 10×10 grid points, and the temperature and concentration of the reconstruction model were not evenly distributed, so the unimodal distribution and bimodal distribution were used to describe the concentration distribution. The simulated system also calculated the effective utilization of laser beams and absorption lines. The results showed that the reconstruction quality quickly increased with increasing H2O absorption lines when the laser beams were very few, the increased absorption lines could get more spectral information related to the concentration. The increased laser beam is also effective to improve the accuracy of reconstruction results, but increasing the absorption lines can better reconstruct a two-dimensional concentration distribution. Improving the absorption lines can also effectively reduce the costs of the hardware and the complexity of the measurement system, which shows that the multispectral absorption lines are applicable to in-situ measurements.

[Simulation of Concentration Measurement of SO(2), NO(2) and Particles Simultaneously by Differential Optical Absorption Spectroscopy].

Our daily life is disturbed seriously by the haze weather now. It is very important to measure the haze composition quantificationally. The main composition of haze is SO(2), NO(2) and particles. At present, the research of measuring gas and particle simultaneously is rare relatively. This paper use differential optical absorption spectroscopy (DOAS) to simulate the concentration measurement of gas and particle simultaneously and obtain some meaningful results. Absorption spectral of many groups of different concentration of SO(2), NO(2) and particle were simulated, and each concentration was inverted by DOAS. In the first group of single component, the concentration change from 100 to 1 000 ppm, the inverted error of SO(2) is not greater than 0.17%, and which is 0.64% for NO(2). When the diameter of particle change from 100 to 500 nm, the inverted error is not greater than 2.08%. In the second group of multiple gases, when the concentration ratio of SO(2) and NO(2) is at the range of 1 : 10 and 5 : 1, the error of SO(2) is not bigger than 8%, and 5% for NO(2), relatively. But when the concentration of SO(2) is 10 times than NO(2), the error is higher than 10% for NO(2). In the third group of gas and particle, the error of gas concentration is lower than 10%, but the concentration error of particle is depended on signal to noise ratio (SNR) greatly. When SNR is higher than 40 dB, error can lower than 10% and when SNR is lower than 30dB, the error is bigger than 20%. From these results, we can see that DOAS can measurement SO(2), NO(2) and particles simultaneously effectively, and can applied to measure and analyze haze composition. However, when the absorption strength of the gases is different greatly, the strong absorption gas influent the weak absorption gas largely. And the SNR is lower, the error of inverted particle concentration increased greatly. The solution of these problems need better filtering and noise reduction method.

[The Research for Trace Ammonia Escape Monitoring System Based on Tunable Diode Laser Absorption Spectroscopy].

In order to on-line measure the trace ammonia slip of the commercial power plant in the future, this research seeks to measure the trace ammonia by using tunable diode laser absorption spectroscopy under ambient temperature and pressure, and at different temperatures, and the measuring temperature is about 650 K in the power plant. In recent years lasers have become commercially available in the near-infrared where the transitions are much stronger, and ammonia's spectroscopy is pretty complicated and the overlapping lines are difficult to resolve. A group of ammonia transitions near 4 433.5 cm(-1) in the v2 +v3 combination band have been thoroughly selected for detecting lower concentration by analyzing its absorption characteristic and considering other absorption interference in combustion gases where H2O and CO2 mole fraction are very large. To illustrate the potential for NH3 concentration measurements, predictions for NH3, H2O and CO2 are simultaneously simulated, NH3 absorption lines near 4 433.5 cm(-1) wavelength meet weaker H2O absorption than the commercial NH3 lines, and there is almost no CO2 absorption, all the parameters are based on the HITRAN database, and an improved detection limit was obtained for interference-free NH3 monitoring, this 2.25 µm band has line strengths several times larger than absorption lines in the 1.53 µm band which was often used by NH3 sensors for emission monitoring and analyzing. The measurement system was developed with a new Herriott cell and a heated gas cell realizing fast absorption measurements of high resolution, and combined with direct absorption and wavelenguh modulation based on tunable diode laser absorption spectroscopy at different temperatures. The lorentzian line shape is dominant at ambient temperature and pressure, and the estimated detectivity is approximately 0.225 x 10(-6) (SNR = 1) for the directed absorption spectroscopy, assuming a noise-equivalent absorbance of 1 x 10(-4). The heated cell experiments with controlled the temperature were performed to validate the sensing strategy. Here the Wavelength Modulation Spectroscopy (WMS) strategy was usually used to measure lower gas concentration for high noise immunity to the non-absorption transmission losses. The great agreement 2f signal with the calibrated concentration is within the uncertainty at different temperatures by using simple digital signal processing such as multiple averages, wavelet analysis and so on. The denoise processing has a great advantage in application and implementation over other noise suppression techniques. The result provided a good basis for trace ammonia escape detection based on tunable diode laser absorption spectroscopy.

Removal efficiencies for 136 tetra- through octa-chlorinated dibenzo-p-dioxins and dibenzofuran congeners with activated carbons.

In this study, the removal efficiency of 136 tetra- to octa-chlorinated dibenzo-p-dioxin (CDD)/furan (F) congeners from a nitrogen + oxygen carrier gas was studied using a laboratory-scale, fixed bed adsorption system. Two kinds of activated carbon with dissimilar pore structures were used as adsorbents. The total concentration of polychlorinated dibenzo-p-dioxins/furans (PCDD/Fs) in the source gas was 541 ng/Nm(3) and that of the 17 toxic 2,3,7,8-substituted PCDD/Fs 96.35 ng/Nm(3), accounting for 17.8% of the total original weight amount. Their toxic equivalent quantity (TEQ) was 8.31 ng I-TEQ/Nm(3). For both activated carbons, the removal efficiencies of the ten PCDD/F homologue groups rise with chlorine substitution number. The removal efficiencies vary approximately as a power function of vapor pressure (correlation coefficients r(2) = 0.93 and 0.81, respectively). Competitive adsorption and desorption occur as adsorption time went on, causing elution of the lower chlorinated homologues, i.e. tetra-CDD/F and Penta-CDD/F congeners. In addition, there are significantly different concentration distributions for isomers in the same homologue groups. However, their removal efficiencies have weak correlation with their initial concentrations. The correlation coefficients are from -0.47 to 0.32 and from -0.57 to 0.46 respectively for the two kinds of activated carbons.

PCDD/Fs' suppression by sulfur-amine/ammonium compounds.

Three distinct -S and -NH2 or NH4(+) containing compounds, including ammonium thiosulfate, aminosulfonic acid and thiourea, were studied as polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) inhibitors. All these three -S and -N containing compounds tested show strong suppression of PCDD/Fs formation, especially for thiourea which has not been studied before. With a (S+N)/Cl molar ratio of only 0.47, thiourea could inhibit 97.3% of PCDD/Fs and even 99.8% of I-TEQ. At an unusually high de novo test temperature (650 °C), the PCDD/Fs' formation was still very low but also the inhibition capacity of thiourea was weak, with an efficiency of 59% for PCDD/Fs when with a (S+N)/Cl molar ratio of 1.40. The results also revealed that the inhibition capability of the combined -S/-NH2 or -S/NH4(+) suppressant was strongly influenced by both the nature of the functional group of nitrogen and the value of the molar ratio (S+N)/Cl. The amine functional group -NH2 tends to be more efficient than ammonium NH4(+) and within a certain range a higher (S+N)/Cl value leads to a higher inhibition efficiency. Moreover, the emission of gases was continuously monitored: the Gasmet results revealed that SO2, HCN and NH3 were the most important decomposition products of thiourea. Thiourea is non-toxic, environment-friendly and can be sprayed into the post-combustion zone in form of powder or aqueous solution. The cost of thiourea at least can be partially compensated by its high inhibition efficiency. Therefore, the application of thiourea in a full-scale incinerator system is promising and encouraging.

Inhibition of the de novo synthesis of PCDD/Fs on model fly ash by sludge drying gases.

Sludge drying gases (SDG), evolving from drying and mild thermal decomposition (<300°C) of raw sewage sludge contain NH3 and SO2 as well as other N- and S-compounds. All of these are potential PCDD/Fs suppressants. It is indeed observed that these SDG suppress 2,3,7,8-substitued PCDD/Fs formation on Model Fly Ash (MFA) with an efficiency up to 97.6% in wt. units and 96% in I-TEQ, respectively. This suppression is strong for (the bulk of) PCDD/Fs, adsorbed on the model fly ash; conversely, sludge drying gases enhance PCDD/Fs desorption from MFA. Moreover, TCDD/Fs are suppressed least, possibly following stepwise dechlorination of higher chlorinated PCDD/Fs. Characteristics, such as the type, origins and amount of sludge, its moisture-, nitrogen- and sulfur content and the nature of the thermal treatment applied are all expected to influence upon the suppression capabilities. In this study three types of dry sludge are tested and applied as suppressant in four different amounts or modes. The quality of the sludge drying gases is continuously monitored: the Gasmet results reveal that NH3 and SO2 are the most important components of SDG. The MFA reaction residue is scrutinized by Scanning Electron Microscope (SEM) and Energy Dispersive Spectrometer (EDS) analysis. A large number of particles attaching to the surface of model fly ash are observed by SEM. Moreover, EDS analysis reveals that part of the chlorine in MFA is carried away with the SDG and replaced by sulfur, so that eliminating chlorine may be part of the inhibition mechanism. However, further research is still needed to establish the optimum operating modes and to confirm the role of both inorganic and organic nitrogen and sulfur compounds in the suppression of PCDD/Fs formation on model fly ash.

Treating PCDD/Fs by combined catalysis and activated carbon adsorption.

V2O5-WO3/TiO2 catalysts are used to destroy dioxins present in the gas phase, yet both their removal efficiency (RE) and destruction efficiency (DE) decrease with rising initial concentration (IC). Therefore, activated carbons (AC-1: based on lignite; AC-2: based on coconut shell) were mixed with the catalyst to tackle these high IC gases. A gas phase dioxin-generating system was used to supply three different stable IC-values. When the highest IC is used (20.5 ng I-TEQ Nm(-3)) without AC, at 200°C, the RE and DE-value of PCDD/Fs reaches only 76% and 64%, respectively. At the same conditions, using a mix of catalyst and AC-2, these RE and DE-values rise to 90.1% and 82.0%, respectively. The mix catalyst/AC also shows better performance at low temperature (160 and 180°C). The AC characteristics influence upon the adsorption and degradation abilities of the mixtures.

Ozone-enhanced oxidation of PCDD/Fs over V(2)O(5)-TiO(2)-based catalyst.

The catalytic oxidation of PCDD/Fs (polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans) vapors was studied in a temperature range of 180-220°C on a honeycomb V2O5-TiO2-based catalyst, in the presence and the absence of ozone. A stable dioxin-generating system was established to support the experimental program and this system could adjust the concentration of PCDD/Fs by injecting appropriate mother liquors. At 220°C the removal efficiency(1) (RE) of PCDD/Fs reaches up to 97% and the degradation efficiency (DE) up to 90%. Both values diminish at lower operating temperatures. In the presence of ozone, however, these values rise to 99% and 98% at 220°C. Especially at low temperatures the effect of ozone is obvious. Catalytic oxidation with ozone thus offers a low-temperature solution to achieve higher rates and low activation energies. The morphology and microstructure of the catalysts changes after ozone treatment and some of their characteristics seem closely related with DE-values.

Dioxins and their fingerprint in size-classified fly ash fractions from municipal solid waste incinerators in China--mechanical grate and fluidized bed units.

The distribution of polychlorinated dibenzo-p-dioxins/dibenzofurans (PCDD/Fs), in brief dioxins, has seldom been addressed systematically in fly ash from municipal solid waste incinerators (MSWIs). This study shows the amount and fingerprint of PCDD/Fs in fly ash from four different Chinese MSWIs, that is, three mechanical grate units and one circulating fluidized bed unit. In these fly ash samples, dioxins-related parameters (international toxic equivalent quantity, total amount of PCDD/Fs, individual isomer classes, and 17 toxic 2,3,7,8-substituted congeners) all tend to increase with decreasing particle size for mechanical grate incinerators, yet only for the finest fraction for fluidized bed units. Moreover, the fluidized bed incinerator seems superior to grate incineration in controlling dioxins, yet a comparison is hampered by internal differences in the sample, for example, the fluidized bed fly ash has much lower carbon and chlorine contents. In addition, the presence of sulfur from mixing coal as supplemental fuel to the MSW may poison the catalytic steps in dioxins formation and thus suppress the formation of dioxins. With more residual carbon and chlorine in the fly ash, it is easier to form dioxins during cooling. Nevertheless, there is no apparent relation between Fe, Cu, and Zn contents and that of dioxins in fly ash.

[The reconstruction of two-dimensional distributions of gas concentration in the flat flame based on tunable laser absorption spectroscopy].

The experimental method by using the tunable diode laser absorption spectroscopy combined with the model and algo- rithm was studied to reconstruct the two-dimensional distribution of gas concentration The feasibility of the reconstruction program was verified by numerical simulation A diagnostic system consisting of 24 lasers was built for the measurement of H2O in the methane/air premixed flame. The two-dimensional distribution of H2O concentration in the flame was reconstructed, showing that the reconstruction results reflect the real two-dimensional distribution of H2O concentration in the flame. This diagnostic scheme provides a promising solution for combustion control.

Baseline soil levels of PCDD/Fs established prior to the construction of municipal solid waste incinerators in China.

In order to determine the baseline contamination by polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in different areas in China, prior to the construction of municipal solid waste incinerators (MSWIs), a total of 32 representative soil samples was collected near 16 incinerators and analyzed for their PCDD/F concentrations. The PCDD/F baseline concentrations in the soil samples ranged from 0.32 to 11.4 ng I-TEQ kg(-1) (dry matter), with average and median value of 2.73 and 2.24 ng I-TEQ kg(-1) (dry matter), respectively, and a span between maximum and minimum recorded value of 36. The PCDD homologues predominated in 26 out of 32 soil samples, with the ratio (PCDDs)/(PCDFs) ranging from 1.1 to 164; however in the other 6 samples, PCDF homologues were larger, with the same ratio varying from 0.04 to 0.8. Principal component analysis (PCA) and hierarchical cluster analysis (HCA) were used to examine PCDD/F amount and profile in these soil samples, and their possible associations with known emission sources: in this process 6 really distinct isomer fingerprints were identified. Background PCDD/F levels and profiles were comparable to those found in soils from China and other countries and indicate a rather low baseline PCDD/F contamination of soils. The present data provide the tools for future assessment of a possible impact of these MSWIs.

Photocatalytic decomposition on nano-TiO2: destruction of chloroaromatic compounds.

Photocatalysis is applied increasingly in addressing and solving environmental and energy-related problems. Especially the TiO2-derived catalysts attract attention because of their catalytic efficiency, wide range of applications, ease in use, and low cost (it costs about 150 Yuan a kilogram in China). This review first describes the principles of photocatalytic destruction by semiconductors and then focuses on degradation rates and reaction mechanisms in a variety of photocatalytic uses of modified TiO(2). Finally, these concepts are illustrated by selected examples relating to the photocatalytic degradation of organic persistent pollutants, such as polychlorinated benzenes (PCBz), biphenyls (PCB) and dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). And some approaches towards industrial application are analyzed.

[Study of a wire-to-plate positive pulsed corona discharge reactor by emission spectroscopy].

In order to get extensive knowledge of wire-to-plate pulsed corona discharge reactor, the influences of different diameters of wire electrode, different wire-to-plate and wire-to-wire spacing on OH radical generation were experimentally investigated under atmospheric pressure based on emission spectrum, and the spatial distribution of OH radicals in the electric field was also discussed in detail The results showed that OH radicals decrease along the X-axis, and the activation radius is approximately 20 mm; showing a trend of first increase and then decrease along the Y-axis, with the activation radius being more than 30 mm. OH radical has small change as the diameter of wire electrode changes below 2 mm, with a sharp decline as the diameter continues to increase. OH radical emission intensity increases as wire-to-wire spacing increases and decrease as wire-to-plate spacing increases.

[Analysis of streamer properties and emission spectroscopy of 2-D OH distribution of pulsed corona discharge].

Streamer plays a key role in the process of OH radical generation. The propagation of primary and secondary streamers of positive wire-plate pulsed corona discharge was observed using a short gate ICCD in air environment. The influence of the applied voltage on the properties was investigated. It was shown that the primary streamer propagation velocity, electric coverage and length of secondary streamer increased significantly with increasing the applied voltage. Then 2-D OH distribution was investigated by the emission spectrum. With the analysis of the OH emission spectra, the distribution of OH radicals showed a trend of decreasing from the wire electrode to its circumambience. Compared with the streamer propagation trace, the authors found that OH radical distribution and streamer are in the same area. Both OH radical concentration and the intensity of streamer decreased when far away from the wire electrode.

Levels of PCDD/Fs in soil in the vicinity of a medical waste incinerator in China: the temporal variation during 2007-2009.

In 2004, it is estimated that 1.18 kg I-TEQ of polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) emitted from medical waste incinerators (MWIs) in China, accounting for 11.5% of the total PCDD/Fs emissions. So it is essential to assess the environmental impact of MWIs. A new MWI of China was started operation in May 2007, and implemented an advanced technology in the combustion and air pollution control system by the BAT/BEP guideline in August 2008. From 2007 to 2009, levels of PCDD/Fs were determined in soil collected in the vicinity of this MWI. The blank survey (2007) was conducted before the start-up operation of this plant. After the operation, soil samples were collected again at the same sampling sites as the blank survey. The average concentration of PCDD/Fs in soil increased from 1.13 pg I-TEQ g(-1) to 2.29 pg I-TEQ g(-1) after 1 year operation of the MWI (2007-2008), and a marked decrease (0.50 pg I-TEQ g(-1)) was observed during 2008-2009. In addition, the current level (2009) was still higher than the blank value (2007). The composited analysis of the experimental results indicated levels of PCDD/Fs were still comparative lower and a limited neighbourhood of the MWI was slightly affected by the emission from this incinerator, meanwhile other un-known PCDD/Fs sources and potential influenced factors could not be neglected in this investigated region.

[Study of emission spectroscopy of OH radicals in pulsed corona discharge].

In the present paper, OH radicals generated by pulsed corona discharge in humidified air, N2 and Ar in a needle-plate reactor were measured by emission spectra. With the analysis of the emission spectra, the influence of pulse peak voltage and frequency on OH radical generation was investigated in the three kinds of background gases. The influence of the gas humidity on the generation and the distribution of OH radicals in the electric field was also discussed in detail. The authors studied the influence of the gas humidity on the generation of OH radicals in the electric field by the control of accurate change in humidity, and we also studied the distribution of OH radicals in the electric field in different background gases including humidified air, N2 and Ar by the accurate change in scales. The experiment shows that the output of OH radicals grows as the pulse peak voltage and frequency grow, but the influence of gas humidity on the process of generating OH radicals by pulsed corona discharge depends on the discharge background. The rules of the generation change when the background gases change. As the humidity in the background gases grows, the amount of OH radicals grows in the air, but it grows at first and decreases at last in N2, while it decreases at first and grows at last in Ar. The distribution of OH radical shows a trend of decreasing from the needle-electrode to its circumambience.