Gold-coated tilted fiber Bragg gratings for lead ion sensing.

Surface plasmon resonance sensor based on gold-coated tilted fiber Bragg gratings (SPR-TFBGs) are perfectly suited for fine refractometry. Thanks to the functionalization of the gold layer, they can be used for label-free biosensing. They have been largely used for the specific detection of proteins and cells. In this work, we experimentally demonstrate that they are enough sensitive to detect a very small entity like an environmental pollutant. In this context, we report here a bio-functionalization of the SPR-TFBG with thrombin aptamers for lead ion detection. We used aqueous solutions of lead ions with increasing concentrations from 0.001 ppb to 10 ppb. Based on the affinity bending of Pb2+ ions to the thrombin aptamer, we experimentally demonstrated low detection level of lead ion concentration (0.001 ppb) while the saturation limit is meanly fixed by the physical dimension of the sensor and the binding efficiency.

Femtosecond pulse laser-engineered glass flexible structures instrumented with an in-built Bragg grating sensor.

The advent of near-infrared femtosecond pulse laser has enabled the highly-resolved manufacturing of micro/nano structures in various materials including glass. In this paper, we make use of an automated femtosecond laser system, so-called Femtoprint, to design a monolithic self-instrumented mechanism that we use for in-built strain sensing. To that aim, a flexible structure is designed and produced from a silica planar substrate. It has a flexural joint in which an optical waveguide and a Bragg grating have been directly inscribed using femtosecond pulse laser. The latter provides a non-destructive and non-intrusive measurement tool. The axial strain sensitivity of the in-built Bragg grating has been experimentally determined to be 1.22 pm/µ ϵ, while its temperature sensitivity is 10.51 pm/°C. The demonstration of such instrumented glass flexible mechanisms paves the way towards a new class of highly integrated sensors suitable for applications at the microscale or in harsh environments.

Gamma-radiation enhancement of sensing properties of FBGs in a few-mode polymer CYTOP fiber.

We investigate the effect of γ-radiation on temperature (T) and relative humidity (RH) sensitivities of polymer perfluorinated fiber Bragg gratings (FBGs). To this aim, different γ-radiation doses (80, 120, 160, and 520 kGy) were applied to a set of FBGs. We show that irradiated FBGs demonstrate an RH sensitivity rise with the received dose: from 13.3 pm/%RH for a pristine FBG up to 56.8 pm/%RH for a 520-kGy dose at 30℃. In contrast, T sensitivity decreases with radiation dose with a subsequent change of sign from positive to negative. Therefore, by experimental interpolation, T sensitivity can be eliminated at around a 160-kGy dose. This opens the possibility of designing an RH sensor with enhanced sensitivity, which at the same time is insensitive to T.

Plasmonic biosensing with tilted fiber Bragg gratings interrogated using a 512-pixel spectrometer.

Plasmonic tilted fiber Bragg gratings (TFBGs) are very efficient for fast, accurate, and minimally invasive biosensing. Their transmitted amplitude spectrum is a dense comb of narrowband cladding mode resonances (full width at half maximum < 1 nm) that is usually demodulated using highly resolved (wavelength resolution < 10 pm) devices. This work demonstrates the possibility of using a coarsely resolved spectrometer (166 pm) to read out the amplitude spectrum of a gold-coated TFBG. A refined analysis of the spectral content has allowed us to develop signal processing that provides a refractometric sensitivity of 2656 nm/RIU. This is a fivefold improvement compared to previously reported read-out techniques. Biosensing has then been successfully implemented with gold-coated TFBGs implemented in reflection mode for the detection of insulin, with specific antibodies grafted on the gold surface. Our experimental work is a first step toward the industrialization of the FBG technology, as it opens the door to fast parallel biosensing, profiting from the multiple sensing channels (up to 64) of the interrogator and its high processing speed (repetition rate up to 3 kHz).

Electro-plasmonic-assisted biosensing of proteins and cells at the surface of optical fiber.

An electro-plasmonic biosensor is used to attract proteins and cells on the surface of a fiber optic probe by controlled biomolecular migration. Concentrating targets on a high performance plasmon-assisted fiber grating sensor leads to a drastic enhancement of the limit of detection. This architecture relies on a biofunctionalized gold coated tilted fiber Bragg grating (TFBG) that operates as a working electrode to enable electrophoresis in the probed medium. The applied electric field triggers the attraction of proteins over a distance of almost 250 µm from the sensor surface, which is more than two orders of magnitude larger than the intrinsic penetration depth of the plasmon wave. Quantitative determination of target analytes was performed by cyclic voltammetry measurements using the gold coated fiber as an electrode, simultaneously with optical transmission measurements of the underlying fiber grating. In our work, these electro-plasmonic optrodes were used against a clinically-relevant biomarker in breast cancer diagnosis, namely HER2 (Human Epidermal Growth Factor Receptor-2). In vitro assays confirm that their limit of detection lies in the subpicomolar range for proteins, which is beyond reach of similar sensors without voltammetry. The improved detection limit is further facilitated by an improvement of the signal-to-noise ratio of the read-out process. Whole cell capture is finally demonstrated by the same micro-system.

Phase interrogation of plasmonic tilted fiber Bragg grating biosensors through the Jones formalism.

Gold-coated tilted fiber Bragg gratings (TFBG) are refined plasmonic biosensors, highly sensitive to surrounding refractive index (RI) changes. Their interrogation usually relies on insertion loss measurements for single input polarized light, limiting the set of exploitable features. To overcome this limitation, we trigger the Jones formalism to retrieve the polarization enabling optimized plasmonic excitation for both phase and amplitude measurements. We present an experimental phase shift with a sensitivity as high as 45835°/RIU and further assess this approach to HER2 proteins sensing at 1µg/ml. We compare this angular modality with the one relying on the insertion loss using a quality factor that takes the shift as well as the dispersion into account. This strengthens its relevance in terms of precision for ultra-small RI variations.

Partially gold-coated tilted FBGs for enhanced surface biosensing.

To date, there is clear experimental evidence that gold-coated tilted fiber Bragg gratings (TFBGs) are highly sensitive plasmonic biosensors that provide temperature-compensated detection of analytes at concentrations in the picomolar range. As most optical biosensors, they bring an evanescent wave in the surrounding medium, which makes them sensitive to both surface refractive index variations (= the useful biosensing signal) and to bulk refractive index changes (= the non-useful signal for biosensing). This dual sensitivity makes them prone to drift. In this work, we study partially gold-coated TFBGs around their cross-section. These gratings present the ability to discriminate both volume and surface refractive index changes, which is interesting in biosensing to enhance the signal-to-noise ratio. The effects induced in the TFBGs transmitted amplitude spectra were analyzed for surrounding refractive index (SRI) changes in the range 1.3360-1.3370. Then, the gold film was biofunctionalized with human epidermal growth factor receptor (HER2) aptamers using thiol chemistry. The detection of HER2 proteins (a relevant cancer biomarker) at 10-9 g/mL, 10-8 g/mL and 10-6 g/mL demonstrated the advantage to identify environmental perturbations through the bare area of the TFBGs, which is left not functionalized. The non-specific drifts that could exist in samples are eliminated and a wavelength shift only related to the surface modification is obtained.

Properties of Fiber Bragg Grating in CYTOP Fiber Response to Temperature, Humidity, and Strain Using Factorial Design.

The characteristics of fiber Bragg grating (FBG) in cyclic transparent fluoropolymer (CYTOP) optical fiber have attracted more and more attention in recent years. However, different results of the FBG response to environmental parameters are reported. This work presents a three-variable two-level factorial experimental method to investigate the FBG response to temperature, humidity, and strain in CYTOP fiber. Two uniform FBGs are inscribed separately in CYTOP fiber with and without over-clad. With only eight measuring points, the interactions among three variable parameters are computed and the parameter sensitivities and cross-sensitivities are estimated. Similar temperature and strain sensitivities were found for both gratings, whereas significant cross-sensitivity between humidity and temperature was present only in FBG inscribed in CYTOP fiber with over-clad.

Online Gamma Radiation Monitoring Using Few-Mode Polymer CYTOP Fiber Bragg Gratings.

We investigated the gamma radiation response of fiber Bragg gratings (FBGs) inscribed in a few-mode polymer optical fiber. The fiber had a graded-index CYTOP core of 20 µm and XYLEX overclad of 250 µm in diameter. Four FBGs were exposed to gamma radiation during four irradiation sessions at a 5.3 kGy/h dose rate. The FBGs showed a linear Bragg wavelength shift with the received dose with a mean sensitivity of -3.95 pm/kGy at 43 °C. The increased temperature provides a rise in the sensitivity: it reached -10.6 pm/kGy at 58 °C. After irradiation, the FBGs showed partial recovery, which increased with the received dose. Furthermore, the FBG's reflection power decreased with the dose. This attenuation is mainly due to insertion losses caused by the radiation induced attenuation in the CYTOP fiber. Linear response to the received dose makes CYTOP FBGs attractive for gamma radiation dosimetry. However, temperature dependence of the sensitivity should be compensated in practical applications.

Ultra-fast fiber Bragg grating inscription in CYTOP polymer optical fibers using phase mask and 400 nm femtosecond laser.

Fiber Bragg gratings (FBGs) in cyclic transparent fluoropolymer (CYTOP) optical fiber are the subject of a lot of research as they can be of interest for many applications, such as temperature, humidity, strain, and radiation sensing. We report here a new technique to produce high quality FBGs in CYTOP fiber. It uses a femtosecond laser system operating at 400 nm and a phase mask. In contrast to previously reported results, the gratings are obtained in a few seconds with a writing power as low as 80 µW. With this setup, 2 mm-long gratings with reflectivity up to 92 % and full width at half maximum bandwidth around 0.5 nm were obtained in less than 10 s. The resonance wavelengths of the FBGs are confirmed by numerical computation in the graded-index multimode CYTOP fiber, and the mode selection characteristic of FBGs in CYTOP is investigated. Finally, the temperature sensitivity of CYTOP FBG is measured in different mode groups for heating up and cooling down, showing values independent of the mode group measured, but with a small hysteresis.

800 nm femtosecond pulses for direct inscription of FBGs in CYTOP polymer optical fiber.

We report the inscription of highly reflective fiber Bragg gratings in perfluorinated polymer (CYTOP) optical fibers using 800 nm femtosecond pulses and a line-by-line inscription method. We demonstrate that the energy for grating inscription without damage is below 27 nJ. After the writing process, we show that the grating reflectivity continues to rise for several hours. The obtained gratings show reflectivity degradation with temperature increase, while the Bragg wavelength undergoes a linear temperature dependence of 37.7 pm/°C when the humidity is controlled and the heating/cooling rate is relatively low (≤0.14∘C/min). The humidity sensitivity at a fixed temperature (25°C) is 22.3 pm/%RH. Finally, the axial strain sensitivity is determined to be 1.35 pm/µÉ›.

Plasmonic sensors based on tilted Bragg gratings in multicore optical fibers.

Bare and gold-coated tilted fiber Bragg gratings (TFBGs) can nowadays be considered as a mature technology for volume and surface refractometric sensing, respectively. As for other technologies, a continuous effort is made towards the production of even more sensitive sensors, thereby enabling a high-resolution screening of the surroundings and the possible detection of rare events. To this aim, we study in this work the development of TFBG refractometers in 4-core fibers. In particular, we show that the refractometric sensitivity of the cut-off mode can reach 100 nm/RIU for a bare grating. Using another demodulation method, a tenfold sensitivity increase is obtained when tracking the extremum of the SPR (surface plasmon resonance) envelope for a gold-coated TFBG configuration. Immobilization of DNA probes was performed as a proof-of-concept to assess the high surface sensitivity of the device.

HER2 biosensing through SPR-envelope tracking in plasmonic optical fiber gratings.

In the biomedical detection context, plasmonic tilted fiber Bragg gratings (TFBGs) have been demonstrated to be a very accurate and sensitive sensing tool, especially well-adapted for biochemical detection. In this work, we have developed an aptasensor following a triple strategy to improve the overall sensing performances and robustness. Single polarization fiber (SPF) is used as biosensor substrate while the demodulation is based on tracking a peculiar feature of the lower envelope of the cladding mode resonances spectrum. This method is highly sensitive and yields wavelength shifts several tens of times higher than the ones reported so far based on the tracking of individual modes of the spectrum. An amplification of the response is further performed through a sandwich assay by the use of specific antibodies. These improvements have been achieved on a biosensor developed for the detection of the HER2 (Human Epidermal Growth Factor Receptor-2) protein, a relevant breast cancer biomarker. These advanced developments can be very interesting for point-of-care biomedical measurements in a convenient practical way.

Multimodal plasmonic optical fiber grating aptasensor.

Tilted fiber Bragg gratings (TFBGs) are now a well-established technology in the scientific literature, bringing numerous advantages, especially for biodetection. Significant sensitivity improvements are achieved by exciting plasmon waves on their metal-coated surface. Nowadays, a large part of advances in this topic relies on new strategies aimed at providing sensitivity enhancements. In this work, TFBGs are produced in both single-mode and multimode telecommunication-grade optical fibers, and their relative performances are evaluated for refractometry and biosensing purposes. TFBGs are biofunctionalized with aptamers oriented against HER2 (Human Epidermal Growth Factor Receptor-2), a relevant protein biomarker for breast cancer diagnosis. In vitro assays confirm that the sensing performances of TFBGs in multimode fiber are higher or identical to those of their counterparts in single-mode fiber, respectively, when bulk refractometry or surface biosensing is considered. These observations are confirmed by numerical simulations. TFBGs in multimode fiber bring valuable practical assets, featuring a reduced spectral bandwidth for improved multiplexing possibilities enabling the detection of several biomarkers.

Implementation of a Mobile Platform Based on Fiber Bragg Grating Sensors for Automotive Traffic Monitoring.

Instrumentation techniques, implementation and installation methods are major concerns in today's distributed and quasi-distributed monitoring applications using fiber optic sensors. Although many successful traffic monitoring experiments have been reported using Fiber Bragg Gratings (FBGs), there has been no standardized solution proposed so far to have FBG seamlessly implemented in roads. In this work, we investigate a mobile platform including FBG sensors that can be positioned on roads for the purpose of vehicle speed measurements. The experimental results prove the efficiency of the proposed platform, providing a perspective toward weigh-in-motion systems.

Fiber Bragg grating regeneration at 450°C for improved high temperature sensing.

Type-I fiber Bragg gratings photo-inscribed in hydrogen-loaded B/Ge co-doped silica single-mode optical fibers have been regenerated efficiently at 450°C, which is the lowest temperature reported so far. The mechanical strength of the annealed fiber is preserved while ensuring temperature sensing of the regenerated gratings up to 900°C. Unlike low temperature cycles (≤600°C), an annealing process at higher temperatures revealed faster regeneration for strong gratings. Changes in grating strength were also measured before the regeneration cycle. These behaviors suggest the contribution of different mechanisms to the regeneration process with different relative dynamics.

Non-enzymatic D-glucose plasmonic optical fiber grating biosensor.

Saccharide sensors represent a broad research area in the scope of sensing devices and their involvement in the medical diagnosis field is particularly relevant for cancer detection at early stage. In that context, we present a non-enzymatic optical fiber-based sensor that makes use of plasmon-assisted tilted fiber Bragg gratings (TFBGs) functionalized for D-glucose biosensing through polydopamine (PDA)-immobilized concanavalin A (Con A). Our probe allows a live and accurate monitoring of the PDA layer deposition leading improved surface biochemistry. The SPR shift observed was assessed to 3.83 ±â€¯0.05 nm within 20 min for a 2 mg/mL dopamine solution. Tests performed in different D-Glucose solutions have revealed a limit of detection close to 10-7 M with the highest sensitivity in the 10-6 to 10-4 M range. This configuration has the capability to overcome the limitations of current enzyme-based solutions.

Anomalous transparency in photonic crystals and its application to point-by-point grating inscription in photonic crystal fibers.

It is common belief that photonic crystals behave similarly to isotropic and transparent media only when their feature sizes are much smaller than the wavelength of light. Here, we counter that belief and we report on photonic crystals that are transparent for anomalously high normalized frequencies up to 0.9, where the crystal's feature sizes are comparable with the free space wavelength. Using traditional photonic band theory, we demonstrate that the isofrequency curves can be circular in the region above the first stop band for triangular lattice photonic crystals. In addition, by simulating how efficiently a tightly focused Gaussian beam propagates through the photonic crystal slab, we judge on the photonic crystal's transparency rather than on isotropy only. Using this approach, we identified a wide range of photonic crystal parameters that provide anomalous transparency. Our findings indicate the possibility to scale up the features of photonic crystals and to extend their operational wavelength range for applications including optical cloaking and graded index guiding. We applied our result in the domain of femtosecond laser micromachining, by demonstrating what we believe to be the first point-by-point grating inscribed in a multi-ring photonic crystal fiber.

Bragg grating inscription in PMMA optical fibers using 400-nm femtosecond pulses.

In this Letter, we report the fast growth of high quality uniform Bragg gratings in trans-4-stilbenemethanol (TS)-doped poly(methyl methacrylate) (PMMA) step-index optical fibers. Grating manufacturing was obtained using a 400 nm femtosecond pulsed laser and a 1060-nm-period uniform phase mask. For 20 mW mean laser beam power, the grating reflectivity reaches 98% in ∼60 s.

Negative axial strain sensitivity in gold-coated eccentric fiber Bragg gratings.

New dual temperature and strain sensor has been designed using eccentric second-order fiber Bragg gratings produced in standard single-mode optical fiber by point-by-point direct writing technique with tight focusing of 800 nm femtosecond laser pulses. With thin gold coating at the grating location, we experimentally show that such gratings exhibit a transmitted amplitude spectrum composed by the Bragg and cladding modes resonances that extend in a wide spectral range exceeding one octave. An overlapping of the first order and second order spectrum is then observed. High-order cladding modes belonging to the first order Bragg resonance coupling are close to the second order Bragg resonance, they show a negative axial strain sensitivity (-0.55 pm/µÎµ) compared to the Bragg resonance (1.20 pm/µÎµ) and the same temperature sensitivity (10.6 pm/°C). With this well conditioned system, temperature and strain can be determined independently with high sensitivity, in a wavelength range limited to a few nanometers.