The combination of baseline magnetic resonance perfusion-weighted imaging-derived tissue volume with severely prolonged arterial-tissue delay and diffusion-weighted imaging lesion volume is predictive of MCA-M1 recanalization in patients treated with endovascular thrombectomy.

INTRODUCTION: Indices of collateral flow deficit derived from MR perfusion imaging that are predictive of MCA-M1 recanalization after intravenous thrombolysis have been recently reported. Our objective was to test the performance of such MRI-derived collateral flow indices for prediction of recanalization after endovascular thrombectomy. METHODS: Fifty-seven patients with MCA-M1 occlusion evaluated with multimodal MRI prior to thrombectomy were included. Bayesian processing allowed quantification of collateral perfusion indices like the volume of tissue with severely prolonged arterial-tissue delay (>6 s) (VolATD6). Baseline DWI lesion volume was also measured. Correlations with angiographic collateral flow grading and post-thrombectomy recanalization were assessed. RESULTS: VolATD6 < 27 ml or DWI lesion volume <15 ml provide the most accurate diagnosis of excellent collateral supply (p < 0.0001). The combination of VolATD6 > 27 ml and DWI lesion volume >15 ml significantly discriminates recanalizers versus nonrecanalizers (whole cohort, p = 0.032; MERCI cohort (n = 50), p = 0.024). When both criteria are positive, 76.2 % of the patients treated with the MERCI retriever do not fully recanalize (p = 0.024). In multivariate analysis, the aforementioned combined criterion and the angiographic collateral grade are the only independent predictors of recanalization with the MERCI retriever (p = 0.015 and 0.029, respectively). CONCLUSION: Bayesian arterial-tissue delay maps and DWI maps provide a non-invasive assessment of the degree of collateral flow and a combined index that is predictive of MCA-M1 recanalization after endovascular thrombectomy. Further studies are needed to evaluate the accuracy of this index in patients treated with novel stent retriever devices.

Semi-automated stereoradiographic upper limb 3D reconstructions using a combined parametric and statistical model: a preliminary study.

PURPOSE: Quantitative assessment of 3D clinical indices may be crucial for elbow surgery planning. 3D parametric modeling from bi-planar radiographs was successfully proposed for spine and lower limb clinical investigation as an alternative for CT-scan. The aim of this study was to adapt this method to the upper limb with a preliminary validation. METHODS: CT-scan 3D models of humerus, radius and ulna were obtained from 20 cadaveric upper limbs and yielded parametric models made of geometric primitives. Primitives were defined by descriptor parameters (diameters, angles...) and correlations between these descriptors were found. Using these correlations, a semi-automated reconstruction method of humerus using bi-planar radiographs was achieved: a 3D personalized parametric model was built, from which clinical parameters were computed [orientation and projections on bone surface of trochlea sulcus to capitulum (CTS) axis, trochlea sulcus anterior offset and width of distal humeral epiphysis]. This method was evaluated by accuracy compared to CT-scan and reproducibility. RESULTS: Points-to-surface mean distance was 0.9 mm (2 RMS = 2.5 mm). For clinical parameters, mean differences were 0.4-1.9 mm and from 1.7° to 2.3°. All parameters except from angle formed by CTS axis and bi-epicondylar axis in transverse plane were reproducible. Reconstruction time was about 5 min. CONCLUSIONS: The presented method provides access to morphological upper limb parameters with very low level of radiation. Preliminary in vitro validation for humerus showed that it is fast and accurate enough to be used in clinical daily practice as an alternative to CT-scan for total elbow arthroplasty pre operative evaluation.

Fast 3D reconstruction of the lower limb using a parametric model and statistical inferences and clinical measurements calculation from biplanar X-rays.

In clinical routine, lower limb analysis relies on conventional X-ray (2D view) or computerised tomography (CT) Scan (lying position). However, these methods do not allow 3D analysis in standing position. The aim of this study is to propose a fast and accurate 3D-reconstruction-method based on parametric models and statistical inferences from biplanar X-rays with clinical measurements' (CM) assessment in standing position for a clinical routine use. For the reproducibility study, the 95% CI was under 2.7° for all lower limbs' angular measurements except for tibial torsion, femoral torsion and tibiofemoral rotation ( < 5°). The 95% CI were under 2.5 mm for lower limbs' lengths and 1.5 to 3° for the pelvis' CM. Comparisons between X-rays and CT-scan based 3D shapes in vitro showed mean differences of 1.0 mm (95% CI = 2.4 mm). Comparisons of 2D lower limbs' and 3D pelvis' CM between standing 'Shifted-Feet' and 'Non-Shifted-Feet' position showed means differences of 0.0 to 1.4°. Significant differences were found only for pelvic obliquity and rotation. The reconstruction time was about 5 min.