Development of a flexible film made of polyvinyl alcohol with chitosan based thermosensitive hydrogel.

Background/purpose: A challenge that arises with periodontal regeneration surgery has been associated with the future development of periodontal regeneration membrane to prevent gingiva and fibroblasts invade the wound and allow alveolar bone successfully regenerated. Materials and methods: Chitosan (CS) has the advantages of non-toxicity, biodegradation, biocompatibility, and has been widely used in wound dressings. A flexible film was made using polyvinyl alcohol (PVA) blending CS based thermosensitive hydrogel. Results: The proposed 2% PVA/CS hydrogel has the highest swelling ratio about 720% after 60 min incubation and keeps its area after 10 min incubation for surgery suture. The elastic modulus of 0%, 1%, 2%, and 4% PVA/CS hydrogel were 7.75 ± 1.96, 0.91 ± 0.16, 0.75 ± 0.21, and 0.37 ± 0.06 MPa, respectively. The maximum strain of 2% PVA/CS hydrogel was 101.00 ± 28.03 (%). After 8 weeks biodegradation, the remain weight of 2% PVA/CS hydrogel was 71.36 ± 0.79 (%). Conclusion: In vitro cytotoxicity tests were performed and demonstrated PVA/CS hydrogel significantly improving cell proliferation. This study realized a promising flexible film for periodontal regeneration membrane that can prevent the rapid growth of fibroblasts to invade the wound and be used for periodontal regeneration surgery.

E-cigarette Use, or Vaping, Practices and Characteristics Among Persons with Associated Lung Injury - Utah, April-October 2019.

In August 2019, the Utah Department of Health (UDOH) received reports from health care providers of several cases of lung injury in persons who reported use of electronic cigarette (e-cigarette), or vaping, products (1,2). To describe the characteristics of medical care, potentially related conditions, and exposures among 83 patients in Utah, detailed medical abstractions were completed for 79 (95%) patients. Among patients receiving chart abstractions, 70 (89%) were hospitalized, 39 (49%) required breathing assistance, and many reported preexisting respiratory and mental health conditions. Interviews were conducted by telephone or in person with 53 (64%) patients or their proxies, and product samples from eight (15%) of the interviewed patients or proxies were tested. Among 53 interviewed patients, all of whom reported using e-cigarette, or vaping, products within 3 months of acute lung injury, 49 (92%) reported using any products containing tetrohydrocannabinol (THC), the principal psychoactive component of cannabis; 35 (66%) reported using any nicotine-containing products, and 32 (60%) reported using both. As reported in Wisconsin and Illinois (1), most THC-containing products were acquired from informal sources such as friends or illicit in-person and online dealers. THC-containing products were most commonly used one to five times per day, whereas nicotine-containing products were most commonly used >25 times per day. Product sample testing at the Utah Public Health Laboratory (UPHL) showed evidence of vitamin E acetate in 17 of 20 (89%) THC-containing cartridges, which were provided by six of 53 interviewed patients. The cause or causes of this outbreak is currently unknown (2); however, the predominant use among patients of e-cigarette, or vaping, products with prefilled THC-containing cartridges suggests that the substances in these products or the way in which they are heated and aerosolized play an important role in the outbreak. At present, persons should not use e-cigarette, or vaping, products that contain THC. In addition, because the specific cause or causes of lung injury are not yet known and while the investigation continues, persons should consider refraining from use of all e-cigarette, or vaping, products.

Anaerobic digestion of activated sludge after pressure-assisted ozonation.

This study was undertaken to examine the benefits of pressure-assisted ozonation (PAO) in enhancing solids reduction and biogas production in anaerobic digestion. The results showed significant improvements in both. With unacclimated inoculum at varied food-to-inoculum (F/I) ratios of 0.5-2, solids and COD reductions were improved by PAO, as well as by increased F/I ratios even without PAO, which would warrant further optimization of the F/I ratio for an unacclimated inoculum. With acclimated inocula at F/I ratio of 0.8, volatile suspended solids reduction and biogas production were improved by up to 60% and 800%, respectively, when the AS had been subjected to 20 cycles of PAO. In extended operation in plants where acclimated anaerobes are encountered, PAO pretreatment offers improved digestion of AS in terms of solids and COD removals and biogas production.

Improved solubilization of activated sludge by ozonation in pressure cycles.

The generation of a large volume of activated sludge (AS) from wastewater treatment has increasingly become a great burden on the environment. Anaerobic digestion is routinely practiced for excess waste sludge; however, the process retention time is long because of kinetic limitation in the hydrolysis step. We tested the feasibility of applying ozone in pressure cycles to enhance the disintegration and solubilization of AS with the goal to prepare them for digestion using reduced ozone dose and contact time. The AS was subjected to repetitive pressure cycles in a closed vessel in which an ozone gas mixture was compressed into the slurry to reach 1040 kPa in the headspace to be followed by rapid venting. For a returned AS with total COD (tCOD) of 8200 mg L(-1), a dose of 0.01 gO(3)g(-1) total suspended solids (TSS) delivered via 20 pressure cycles within 16 min resulted in a 37-fold increase of the sCOD/tCOD ratio (due to increased soluble COD, i.e. sCOD) and a 25% reduction of TSS, in comparison to a dose of 0.08 gO(3)g(-1) TSS via bubbling contact over 15 min that resulted in a 15-fold increase of the sCOD/tCOD ratio and a 12% reduction of TSS. Sludge solubilization was evidenced by increased dissolved contents of total phosphorous (from 10 to 64 mg L(-1)), total nitrogen (from 14 to 120 mg L(-1)), and protein (from <15 to 39 mg L(-1)) in the sludge suspension after treatment, indicating significant solubilization of AS.

Removal of oil and oil sheen from produced water by pressure-assisted ozonation and sand filtration.

Ever increasing energy demand worldwide necessitates energy supply, inevitably leading to an increasing volume of process waters containing hydrocarbon contaminants. Among them, dispersed and dissolved oils in produced water need to be removed adequately in order to reuse or avoid surface sheen from coastal discharge. We have recently developed a new ozonation technique coupled with sand filtration to quickly remove oil from process water and prevent oil sheen. The technique incorporates rapid, successive cycles of compression and decompression during ozonation. Gas bubbles expanding from small to large sizes occur that provide ample reactive zones at the gas-liquid interface, resulting in heightened chemical conversions-notably the conversion of hydrophobic hydrocarbon molecules into hydrophilic ones. This study examined the removal of hydrocarbons and sheen according to treatment parameters and configurations, as assessed by changes in turbidity, COD, BOD, and sheen presence following treatment. When a synthetic produced water containing 120ppm of oil (about 100ppm of dispersed and 20ppm of soluble oil at a total COD of 320mgL(-1)) was subjected to 10 pressure cycles (reaching 1.0MPa; 20s each) of ozonation and sand filtration at 6cmmin(-1) and then repeated by 20 cycles of ozonation and sand filtration, it resulted in removal of oil to 20ppm as water-soluble organic acids, decrease of turbidity from 200 to 2NTU, and complete sequestration of surface sheen. The new technique offers a treatment alternative for produced water and likely other tailings waters, promoting safe discharge to the environment and beneficial uses of the water.

The effectiveness of four organic matter amendments for decreasing resin-extractable Cr(VI) in Cr(VI)-contaminated soils.

This paper compared the effectiveness of four organic materials for decreasing the amounts of soil extractable Cr(VI) in Cr(VI)-contaminated soils using the DOWEX M4195 resin-extraction method. Organic matters were added into Cr(VI)-spiked soils [500 mg Cr(VI)(kgsoil)(-1)] in the form of sugarcane dregs compost (SCDC), cattle-dung compost (CDC), soybean meal (SBM) and rice bran (RB), in the amounts of 0, 1%, and 2% by dry weight, respectively. The results indicated that adding only 1% organic matter to the studied soils could effectively decrease the amount of soil resin-extractable Cr(VI) after 12 days of incubation. The decrease of resin-extractable Cr(VI) by organic materials was mainly the result from the reduction of Cr(VI) to Cr(III) supported by the XANES spectroscopy. Among the four tested organic materials, SBM and RB had higher effectiveness in decreasing soil resin-extractable Cr(VI) than CDC and SCDC. This result may be due to the fact that SBM and RB have more dissolved organic carbon (DOC) and protein than CDC and SCDC. Therefore, it was concluded that the contents of DOC and protein are the main factors that determine the effectiveness of organic materials for decreasing the amounts of soil available Cr(VI) in Cr(VI)-contaminated soils.

The effectiveness of ferrous iron and sodium dithionite for decreasing resin-extractable Cr(VI) in Cr(VI)-spiked alkaline soils.

Ferrous iron, Na(2)S(2)O(4), and a mixture of Fe(II) and Na(2)S(2)O(4) (4:1 mol/mol) were tested for their effectiveness for decreasing resin-extractable Cr(VI) in alkaline Cr(VI)-spiked soils. The results indicated that adding those reductants greatly decreased the amount of resin-extractable Cr(VI) when the application rate of reductants equaled the number of equivalents of dichromate added to the Cr(VI)-spiked soils. This was mainly as a result of the Cr(VI) reduction into Cr(III), as supported by the XANES spectra. Among the tested reductants, a mixture of Fe(II) and Na(2)S(2)O(4) was the most effective to decrease resin-extractable Cr(VI). The extent to which resin-extractable Cr(VI) and soil pH were decreased was affected by the pH of the reductants. Among the tested reductants at various pH, FeSO(4) at pH below 1 was the most effective in decreasing resin-extractable Cr(VI) in alkaline soils. However, the soil pH was the most decreased as well. On the other hand, the mixtures of ferrous iron and dithionite at a wide range of pH were all efficient (>70% efficiency) in decreasing resin-extractable Cr(VI). Moreover, the extent of the decrease in soil pH was much smaller than that by FeSO(4) (pH<1) alone, and thus the possibility of the Cr(III) hazard can be avoided.