High bismuth-doped germanosilicate fiber for efficient E + S-band amplification.

Bismuth-doped germanosilicate fiber (BGSF), the active media of fiber amplifiers, has attracted widespread attention. Here, we report a BGSF with a high bismuth concentration of 0.075 wt. % and achieve high-efficiency E + S-band amplification, which was prepared by the modified chemical vapor deposition (MCVD) process. The small signal absorption (SSA) and unsaturated loss (UL) of BGSF at 1310 nm are 1.32 and 0.11 dB/m, respectively. The results show a record with only 45 m BGSF was created, to the best of our knowledge, which provides a maximum gain of 39.24 dB with an NF of 6.2 dB at 1430 nm under -20 dBm input signal power.

High-efficiency cladding-pumped Er/Yb co-doped alumino-phosphosilicate fiber for an extended L-band amplification.

Extending the gain bandwidth of L-band optical fiber amplifier has provoked a widespread interest. To date, achieving a high-efficiency extended L-band amplification remains a challenge. Here, we report a cladding-pumped Er/Yb co-doped alumino-phosphosilicate fiber, prepared by the modified chemical vapor deposition process. We demonstrate the efficiency of alumino-phosphosilicate glass for cladding-pumped Er/Yb co-doped fiber, with a gain per unit fiber length of 0.45 dB/m at 1625 nm and a gain ripple of ∼9.4 dB. For 0.8 W pump power, the fiber exhibits a 20 dB gain bandwidth covering 1575-1625 nm and 6.9 dB noise figure at 1625 nm. Additionally, the utilization of multi-mode laser diode enables further significant power savings and cost reduction. To the best of our knowledge, Er/Yb co-doped fiber in alumino-phosphosilicate glass is first proposed, with a cladding-pumped scheme for enhancing an extended L-band performance.

Extended L-band 4-Core Er/Yb co-doped fiber amplifier based on 1018†nm cladding pumping.

The extended L-band 4-core Er/Yb co-doped fiber and amplifier (MC-EYDFA) is first proposed and demonstrated, to the best of our knowledge, for space division multiplexing combined with wavelength division multiplexing application. The fiber core co-doped with Er/Yb/P is adopted for bandwidth expansion, and the long wavelength extends to 1625 nm. Numerical simulations further show that efficient amplification and higher saturation power are achieved with the 1018 nm cladding pumping. Based on the integrated 4-core fiber amplifier, an average gain of ∼22 dB covering 1575-1625 nm is experimentally obtained with a 4 W pump power and a 3 dBm total signal power, and the max core-dependent gain (CDG) variation is measured to be 1.7 dB.

Er/Yb co-doped 345-W all-fiber laser at 1535 nm using hybrid fiber.

The 1.5-µm fiber laser is widely used in the fields of laser lidar, remote sensing, and gas monitoring because of its advantages of being eye-safe and exhibiting low atmospheric transmission loss. However, due to the ∼1-µm amplified spontaneous emission (ASE) of the Er/Yb co-doped fiber (EYDF), it is difficult to improve the laser power. Here, we simulated the effect of the Er3+ concentration and the seed power on ∼1-µm ASE, and fabricated a large mode area EYDF by the modified chemical vapor deposition process. Additionally, a piece of ytterbium-doped fiber was introduced into the master oscillator power amplifier (MOPA) configuration to absorb the generated ∼1-µm ASE simultaneously. Experimental results show that an output power of 345 W with a slope efficiency of 43% at 1535 nm is obtained in an all-fiber configuration, profiting from effective suppression of ∼ 1-µm ASE. To the best of our knowledge, this is the highest output power available with an Er/Yb co-doped fiber from an all-fiber MOPA configuration.

3 × 1 fiber signal combiner with high beam quality Gaussian-like beam for a 10kW-level fiber laser.

We present the design and fabrication of a 3 × 1 signal combiner with high beam quality based on supermode theory. For improving beam quality, the fiber with core diameter of 34 µm and numerical aperture of 0.11 is first chosen as the output fiber. An 8.89 kW output laser with a power transmission efficiency of 97.2% and a low temperature rise coefficient of 3.5 °C/ kW at >8 kW is obtained when the combiner launched by three Yb-doped fiber lasers. In addition, the energy density distribution of the output beam is Gaussian-like and M2 factor is 2.32, which is the best beam quality compared with the presented signal combiners for high power laser to the best of our knowledge.

High-efficiency cladding-pumped 4-core erbium-doped fiber with a pedestal for space division multiplexing amplification.

A cladding-pumped 4-core erbium-doped fiber (4C-EDF) with a pedestal structure has been firstly, to the best of our knowledge, proposed and fabricated for space division multiplexing (SDM) amplification. The numerical simulation shows that the index-raised pedestal around the fiber core can improve power conversion efficiency (PCE) by enhancing pump power usage. Compared with conventional 4C-EDF, the 4C-EDF with a pedestal has a gain improvement of 4.5 dB and a PCE enhancement of 91.8%, according to the experimental results (pedestal fiber: 9.55%, conventional fiber: 4.98%). For a 6 dBm total input signal power at L-band and a 7.8 W pump power at 976 nm, the pedestal 4C-EDF shows an average gain of 25 dB and an average noise figure (NF) of 6.5 dB over all cores in the wavelength range of 1570.41 nm to 1610.87 nm. The core-to-core gain variation is less than 2 dB.

Extended L-band few-mode Er/Yb Co-doped fiber amplifier with a cladding-pumped pseudo-two-stage configuration.

Spatial division multiplexing (SDM) is one of the most important technologies that may help to solve the future capacity crisis. However, to date, SDM optical amplification is still a challenge for its application. Herein, we numerically and experimentally demonstrated a few-mode Er/Yb co-doped fiber amplifier (FM-EYDFA) for extended L-band operation. A double cladding Er/Yb co-doped fiber was fabricated to expand the L-band bandwidth and a novel, to the best of our knowledge, cladding-pumped pseudo-two-stage amplification configuration was proposed to enhance the L-band gain. With an initial signal power of -16.8 dBm and an injected pump power of 8.8 W at 940 nm, the 20-dB gain range was covered to 1620 nm for two-mode groups of LP01 and LP11. Importantly, the average gain of 25 dB and average differential modal gain (DMG) of <1 dB were obtained in the wavelength range of 1570-1620 nm for all modes. Our results suggest that the cladding-pumped pseudo-two-stage amplifier based on Er/Yb co-doped fiber providing low DMG, and broad bandwidth has a great potential for increasing the future SDM capacity.

Extending the L-band amplification to 1623 nm using Er/Yb/P co-doped phosphosilicate fiber.

The gain bandwidth of the erbium-doped fiber amplifier limits the enhancement of the transmission capacity in optical fiber communication systems. This Letter reports an erbium-ytterbium co-doped phosphosilicate fiber, which is expected to increase transmission capacity by extending the L-band gain bandwidth to 1623 nm. The fiber was fabricated by modified chemical vapor deposition combined with solution doping technology. The mechanism of bandwidth-expansion by inhibiting the signal excited-state absorption was investigated. When the signal power and pump power were maintained at -3.7dBm and ∼720mW at 1480 nm, the 20 dB gain range was extended out to 1623 nm. Additionally, the noise figure at 1623 nm decreased to 6.01 dB, with 23 dBm saturated output power. The results show that the erbium-ytterbium co-doped phosphosilicate fiber has a great potential for extending L-band amplification.

Yb3+ doped gain guided index anti-guided fiber based on the nanoporous silica glass rod.

We report a heavily Yb3+/Al3+/B3+/F- co-doped high silica rod with a negative refractive index relative to pure silica. The high silica rod was fabricated from nanoporous silica rod using glass phase-separation technology. To lower the refractive index, B3+ and F- were simultaneously introduced into the silica rod and the optical properties of the silica rod were investigated. The fiber preform was prepared with the rod-in-tube method by which the Yb3+ doped high silica rod was only used as an active core. The fiber has a core diameter of 80 µm and a cladding diameter of 400 µm. The measurements show that the Yb3+ in the high silica fiber core is 15856 ppm by weight, while the refractive index is 0.0024 lower than that of the inner cladding. The amplification performance of the fiber was investigated. The results indicate that nanoporous silica glass based on the glass phase-separation technology has great potential for gain-guided index anti-guided high silica fiber.

Numerical investigation of GHz repetition rate fundamentally mode-locked all-fiber lasers.

GHz repetition rate fundamentally mode-locked lasers have attracted great interest for a variety of scientific and practical applications. A passively mode-locked laser in all-fiber format has the advantages of high stability, maintenance-free operation, super compactness, and reliability. In this paper, we present numerical investigation on passive mode-locking of all-fiber lasers operating at repetition rates of 1-20 GHz. Our calculations show that the reflectivity of the output coupler, the small signal gain of the doped fiber, the total net cavity dispersion, and the modulation depth of the saturable absorber are the key parameters for producing stable fundamentally mode-locked pulses at GHz repetition rates in very short all-fiber linear cavities. The instabilities of GHz repetition rate fundamentally mode-locked all-fiber lasers with different parameters were calculated and analyzed. Compared to a regular MHz repetition rate mode-locked all-fiber laser, the pump power range for the mode-locking of a GHz repetition rate all-fiber laser is much larger due to the several orders of magnitude lower accumulated nonlinearity in the fiber cavity. The presented numerical study provides valuable guidance for the design and development of highly stable mode-locked all-fiber lasers operating at GHz repetition rates.

Yb3+ heavily doped photonic crystal fiber lasers prepared by the glass phase-separation technology.

We report a Yb3+ heavily doped photonic crystal fiber with 30 µm core diameter manufactured for the first time by an alternative technique. Silica core rods with a diameter of 3 mm and a length of 280 mm were prepared by the sodium-borosilicate glass phase-separation technology. The measurements show that the fiber has an Yb3+ concentration of 22810 ppm by weight, and a resultant absorption of approximately 8.5 dB/m at 976 nm. The Yb3+ ions are distributed throughout the fiber core with an excellent homogeneity. The laser performance demonstrates a high slope efficiency of 64.5% for laser emission at 1033.4 nm and a low power threshold of 3 W within a short fiber length of 1 m. This novel approach provides an alternative means of preparing large active silica rods with high doping levels and excellent material homogeneity for large mode area fibers with complex designs.

Yb³âº-doped large core silica fiber for fiber laser prepared by glass phase-separation technology.

We report on the preparation and optical characteristics of an Yb(3+)-doped large core silica fiber with the active core prepared from nanoporous silica rod by the glass phase-separation technology. The measurements show that the fiber has an Yb(3+) concentration of 9811 ppm by weight, a low background attenuation of 0.02 dB/m, and absorption from Yb(3+) about 5.5 dB/m at 976 nm. The laser performance presents a high slope efficiency of 72.8% for laser emission at 1071 nm and a low laser threshold of 3 W within only 2.3 m fiber length. It is suggested that the glass phase-separation technology shows great potential for realizing active fibers with larger core and complex fiber designs.

Intense ultra-broadband down-conversion in co-doped oxide glass by multipolar interaction process.

We report that Eu(2+) can be an efficient sensitizer for Yb(3+) and a broadband absorber for blue solar spectra in the host of oxide glass. The greenish 4f → 5d transition of Eu(2+) and the characteristic near-infrared emission of Yb(3+) were observed, with the blue-light of xenon lamp excitation. The 5d energy can be adjusted by the host and the energy transfer efficiency can be enhanced. The quantum efficiency is up to 163.8%. Given the broad excitation band, high absorption coefficient and excellent mechanical, thermal and chemical stability, this system can be useful as down-conversion layer for solar cells.