Effect of cold start on engine performance and emissions from diesel engines using IMO-Compliant distillate fuels.

Emissions from ships at berth are small compared to the total ship emissions; however, they are one of the main contributors to pollutants in the air of densely-populated areas, consequently heavily affecting public health. This is due to auxiliary marine engines being used to generate electric power and steam for heating and providing services. The present study has been conducted on an engine representative of a marine auxiliary, which was a heavy duty, six-cylinder, turbocharged and after-cooled engine with a high pressure common rail injection system. Engine performance and emission characterisations during cold start are the focus of this paper, since cold start is significantly influential. Three tested fuels were used, including the reference diesel and two IMO (International Maritime Organization) compliant spiked fuels. The research engine was operated at a constant speed and 25% load condition after 12 h cooled soak. Results show that during cold start, significant heat generated from combustion is used to heat the engine block, coolant and lubricant. During the first minute, compared to the second minute, emissions of particle number (PN), carbon monoxide (CO), particulate matter (PM), and nitrogen oxides (NOx) were approximately 10, 4, 2 and 1.5 times higher, respectively. The engine control unit (ECU) plays a vital role in reducing engine emissions by changing the engine injection strategy based on the engine coolant temperature. IMO-compliant fuels, which were higher viscosity fuels associated with high sulphur content, resulted in an engine emission increase during cold start. It should be taken into account that auxiliary marine diesel engines, working at partial load conditions during cold start, contribute considerably to emissions in coastal areas. It demonstrates a need to implement practical measures, such as engine pre-heating, to obtain both environmental and public health advantages in coastal areas.

Effect of sulphur and vanadium spiked fuels on particle characteristics and engine performance of auxiliary diesel engines.

Particle emission characteristics and engine performance were investigated from an auxiliary, heavy duty, six-cylinder, turbocharged and after-cooled diesel engine with a common rail injection system using spiked fuels with different combinations of sulphur (S) and vanadium (V) spiking. The effect of fuel S content on both particle number (PN) and mass (PM) was clearly observed in this study. Higher PN and PM were observed for fuels with higher S contents at all engine load conditions. This study also found a correlation between fuel S content and nucleation mode particle number concentration which have more harmful impact on human health than larger particles. The highest PN and PM were observed at partial load conditions. In addition, S in fuel resulted in higher viscosity of spiked fuels, which led to lower engine blow-by. Fuel V content was observed in this study, evidencing that it had no clear effect on engine performance and emissions. Increased engine load also resulted in higher engine blow-by. The lower peak of in-cylinder pressure observed at both pre-mixed and diffusion combustion phases with the spiked fuels may be associated with the lower energy content in the fuel blends compared to diesel fuel.

On-board measurements of particle and gaseous emissions from a large cargo vessel at different operating conditions.

This study investigated particle and gaseous emission factors from a large cargo vessel for her whole voyage including at berth, manoeuvring and cruising. Quantification of these factors assists in minimising the uncertainty in the current methods of exhaust gas emission factor estimation. Engine performance and emissions from the main marine engine were measured on-board while the ship was manoeuvring and cruising at sea. Emissions of an auxiliary engine working at 55% of maximum continuous rating (MCR) were measured when the ship was at actual harbour stopovers. Gaseous and particle emission factors in this study are presented in g kWh-1 or # kWh-1, and compared with previous studies. Results showed that the SO2 emission factor is higher than that of previous studies due to the high sulphur content of the fuel used. The particle number size distributions showed only one mode for different operating conditions of the ship, with a peak at around 40-50 nm, which was dominated by ultrafine particles. Emission factors of CO, HC, PM and PN observed during ship manoeuvring were much higher than that of those recorded at cruising condition. These findings highlight the importance of quantification and monitoring ship emissions in close proximity to port areas, as they can have the highest impact on population exposure.