Fully Differential Touch Screen Controller with Wide Input Dynamic Range for Thin Displays.

As today's smartphone displays become thinner, the coupling capacitance between the display electrodes and touch screen panel (TSP) electrodes is increasing significantly. The increased capacitance easily introduces time-varying display signals into the TSP, deteriorating the touch performance. In this research, we demonstrate that the maximum peak display noise in the time domain is approximately 30% of the maximum voltage difference of the display grayscale through analysis of the structure and operation of displays. Then, to mitigate display noise, we propose a circuit solution that uses a fully differential charge amplifier with an input dynamic range wider than the maximum peak of the display noise. A test chip was fabricated using a 0.35 µm CMOS process and achieved a signal-to-noise ratio of 41 dB for a 6-mm-diameter metal pillar touch when display pulses with 5-V swing were driven at 100 kHz.

Mutual Capacitive Sensing Touch Screen Controller for Ultrathin Display with Extended Signal Passband Using Negative Capacitance.

Flexible and thin displays for smart devices have a large coupling capacitance between the sensor electrode of the touch screen panel (TSP) and the display electrode. This increased coupling capacitance limits the signal passband to less than 100 kHz, resulting in a significant reduction in the received signal, with a driving frequency of several hundred kilohertz used for noise avoidance. To overcome this problem, we reduced the effective capacitance at the analog front-end by connecting a circuit with a negative capacitance in parallel with the coupling capacitance of the TSP. In addition, the in-phase and quadrature demodulation scheme was used to address the phase fluctuation between the signal and the clock during demodulation. We fabricated a test chip using the 0.35 µm CMOS process and obtained a signal-to-noise ratio of 43.2 dB for a 6 mm diameter metal pillar touch input.

A 12-Gb/s Stacked Dual-Channel Interface for CMOS Image Sensor Systems.

We propose a dual-channel interface architecture that allocates high and low transition-density bit streams to two separate channels. The transmitter utilizes the stacked drivers with charge-recycling to reduce the power consumption. The direct current (DC)-coupled receiver front-end circuits manage the common-mode level variations and compensate for the channel loss. The tracked oversampling clock and data recovery (CDR), which realizes fast lock acquisition below 1 baud period and low logic latency, is shared by the two channels. Fabricated in a 65-nm low-power complementary metal-oxide semiconductor (CMOS) technology, the dual-channel transceiver achieves 12-Gb/s data rate while the transmitter consumes 20.43 mW from a 1.2-V power supply.

Tablet coating by injection molding technology - Optimization of coating formulation attributes and coating process parameters.

We developed and evaluated a solvent-free injection molding (IM) coating technology that could be suitable for continuous manufacturing via incorporation with IM tableting. Coating formulations (coating polymers and plasticizers) were prepared using hot-melt extrusion and screened via stress-strain analysis employing a universal testing machine. Selected coating formulations were studied for their melt flow characteristics. Tablets were coated using a vertical injection molding unit. Process parameters like softening temperature, injection pressure, and cooling temperature played a very important role in IM coating processing. IM coating employing polyethylene oxide (PEO) based formulations required sufficient room humidity (>30% RH) to avoid immediate cracks, whereas other formulations were insensitive to the room humidity. Tested formulations based on Eudrajit E PO and Kollicoat IR had unsuitable mechanical properties. Three coating formulations based on hydroxypropyl pea starch, PEO 1,000,000 and Opadry had favorable mechanical (<700MPa Young's modulus, >35% elongation, >95×104J/m3 toughness) and melt flow (>0.4g/min) characteristics, that rendered acceptable IM coats. These three formulations increased the dissolution time by 10, 15 and 35min, respectively (75% drug release), compared to the uncoated tablets (15min). Coated tablets stored in several environmental conditions remained stable to cracking for the evaluated 8-week time period.

Demonstration of pharmaceutical tablet coating process by injection molding technology.

We demonstrate the coating of tablets using an injection molding (IM) process that has advantage of being solvent free and can provide precision coat features. The selected core tablets comprising 10% w/w griseofulvin were prepared by an integrated hot melt extrusion-injection molding (HME-IM) process. Coating trials were conducted on a vertical injection mold machine. Polyethylene glycol and polyethylene oxide based hot melt extruded coat compositions were used. Tablet coating process feasibility was successfully demonstrated using different coating mold designs (with both overlapping and non-overlapping coatings at the weld) and coat thicknesses of 150 and 300 µm. The resultant coated tablets had acceptable appearance, seal at the weld, and immediate drug release profile (with an acceptable lag time). Since IM is a continuous process, this study opens opportunities to develop HME-IM continuous processes for transforming powder to coated tablets.

A Method for Enhancing the Sensing Distance of a Fingerprint Sensor.

In this paper, we describe a method for improving the quality of fingerprint images at long sensing distances by reducing the fringe capacitance formed between a pixel and surrounding fingerprint patterns. Air-walls were applied to the glass attached to a fingerprint sensor for reducing the edge capacitance. Fingerprints and air-wall structures were modeled using a three-dimensional capacitance analysis tool. A prototype was fabricated by stacking glass layers with air-walls with a depth of 50 µm and a pitch of 50 µm on a silicon-type capacitive sensor. Using the results of simulations and prototype experiments, we confirmed that the proposed air-wall structure achieved high enough resolution to distinguish 2.5-lp/mm fingerprint patterns at a sensing distance of 300 µm or longer, and its contrast improved from 0.59 to 0.98.

Integrated hot-melt extrusion - injection molding continuous tablet manufacturing platform: Effects of critical process parameters and formulation attributes on product robustness and dimensional stability.

This study provides a framework for robust tablet development using an integrated hot-melt extrusion-injection molding (IM) continuous manufacturing platform. Griseofulvin, maltodextrin, xylitol and lactose were employed as drug, carrier, plasticizer and reinforcing agent respectively. A pre-blended drug-excipient mixture was fed from a loss-in-weight feeder to a twin-screw extruder. The extrudate was subsequently injected directly into the integrated IM unit and molded into tablets. Tablets were stored in different storage conditions up to 20 weeks to monitor physical stability and were evaluated by polarized light microscopy, DSC, SEM, XRD and dissolution analysis. Optimized injection pressure provided robust tablet formulations. Tablets manufactured at low and high injection pressures exhibited the flaws of sink marks and flashing respectively. Higher solidification temperature during IM process reduced the thermal induced residual stress and prevented chipping and cracking issues. Polarized light microscopy revealed a homogeneous dispersion of crystalline griseofulvin in an amorphous matrix. DSC underpinned the effect of high tablet residual moisture on maltodextrin-xylitol phase separation that resulted in dimensional instability. Tablets with low residual moisture demonstrated long term dimensional stability. This study serves as a model for IM tablet formulations for mechanistic understanding of critical process parameters and formulation attributes required for optimal product performance.

Development of Maltodextrin-Based Immediate-Release Tablets Using an Integrated Twin-Screw Hot-Melt Extrusion and Injection-Molding Continuous Manufacturing Process.

The combination of hot-melt extrusion and injection molding (HME-IM) is a promising process technology for continuous manufacturing of tablets. However, there has been limited research on its application to formulate crystalline drug-containing immediate-release tablets. Furthermore, studies that have applied the HME-IM process to molded tablets have used a noncontinuous 2-step approach. The present study develops maltodextrin (MDX)-based extrusion-molded immediate-release tablets for a crystalline drug (griseofulvin) using an integrated twin-screw HME-IM continuous process. At 10% w/w drug loading, MDX was selected as the tablet matrix former based on a preliminary screen. Furthermore, liquid and solid polyols were evaluated for melt processing of MDX and for impact on tablet performance. Smooth-surfaced tablets, comprising crystalline griseofulvin solid suspension in the amorphous MDX-xylitol matrix, were produced by a continuous process on a twin-screw extruder coupled to a horizontally opening IM machine. Real-time HME process profiles were used to develop automated HME-IM cycles. Formulation adjustments overcame process challenges and improved tablet strength. The developed MDX tablets exhibited adequate strength and a fast-dissolving matrix (85% drug release in 20 min), and maintained performance on accelerated stability conditions.

Fabrication of 3-D curved microstructures by constrained gas expansion and photopolymerization.

This paper describes a novel method of fabricating three-dimensional (3-D) curved microstructures with continuous relief through controlled argon gas expansion into a photocurable resin. A microstructured stamp is placed on top of a nonwetting photopolymerizable liquid resin. The setup is heated, and the argon gas in the blind holes of the stamp expands. The expanded gas displaces the resin at the mouth of the microcavities to form 3-D curved indentations in the liquid resin which is subsequently rapidly solidified by photopolymerization. By changing the duration of the preheating, different curvatures can be produced. Arrays of homogeneous 3-D curved microstructures having different cross-sectional geometries and heights were fabricated using various shapes of the blind holes and preheating times, respectively. As a demonstration of applications, high-quality and uniform polydimethylsiloxane microlens arrays were produced. In addition, thorough investigation was carried out to study the factors influencing the fabricated 3-D curved microstructures. Curved microstructures with diameters as small as 2 microm were demonstrated. A simple model was developed, and such a model allows for predicting the curvatures of indentations with different preheating times. It has been found that the predicted curvatures are in good agreement with experimental data.

UV embossed polymeric chip for protein separation and identification based on capillary isoelectric focusing and MALDI-TOF-MS.

This paper demonstrates a ultraviolet (UV)-embossed polymeric chip for protein separation by capillary isoelectric focusing (CIEF) and identification by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS). The polymeric chip was replicated by a UV-embossing technique using a soft rubber mold. Five diverse widely investigated families of UV-cured formulations were examined for MALDI ionization efficiency of bovine serum albumin (BSA) samples spotted on the polymer surfaces. The signal and signal-to-noise ratio from the polyester formulation were each 12 times those obtained with PMMA (a commonly used polymer material for MALDI) at picomole sample concentration. A polyester chip was successfully used to carry out CIEF to separate proteins, followed by MALDI-TOF-MS identification. Issues related to the successful chip fabrication and protein separation and identification are discussed.