Effect of Feed Mass, Reactor Temperature, and Time on the Yield of Waste Polypropylene Pyrolysis Oil Produced via a Fixed-Bed Reactor.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the response surface methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100, and 150 g) together with the reactor temperature (450, 475, and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e., the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle, and top of the reactor. The recorded temperature diagrams show that, with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to the overcracking of volatile products and, from there, to an increased formation of non-condensable gases, i.e., a reduced yield of pyrolytic oil.

Sublimation Study of Six 5-Substituted-1,10-Phenanthrolines by Knudsen Effusion Mass Loss and Solution Calorimetry.

The vapor pressures of six solid 5-X-1,10-phenanthrolines (where X = Cl, CH3, CN, OCH3, NH2, NO2) were determined in suitable temperature ranges by Knudsen Effusion Mass Loss (KEML). From the temperature dependencies of vapor pressure, the molar sublimation enthalpies, ΔcrgHm0(⟨T⟩), were calculated at the corresponding average ⟨T⟩ of the explored temperature ranges. Since to the best of our knowledge no thermochemical data seem to be available in the literature regarding these compounds, the ΔcrgHm0(⟨T⟩) values obtained by KEML experiments were adjusted to 298.15 K using a well known empirical procedure reported in the literature. The standard (p0 = 0.1 MPa) molar sublimation enthalpies, ΔcrgHm0(298.15 K), were compared with those determined using a recently proposed solution calorimetry approach, which was validated using a remarkable amount of thermochemical data of molecular compounds. For this purpose, solution enthalpies at infinite dilution of the studied 5-chloro and 5-methylphenantrolines in benzene were measured at 298.15 K. Good agreement was found between the values derived by the two different approaches, and final mean values of ΔcrgHm0(298.15 K) were recommended. Finally, the standard molar entropies and Gibbs energies of sublimation were also derived at T = 298.15 K. The volatilities of the six compounds were found to vary over a range of three orders of magnitude in the explored temperature range. The large difference in volatility was analyzed in the light of enthalpies and entropies of sublimation. The latter was tentatively put in relation to the rotational contribution of the substituent group on the phenanthroline unit.

Characterization of Hybrid Materials Prepared by Sol-Gel Method for Biomedical Implementations. A Critical Review.

The interaction between tissues and biomaterials (BM) has the purpose of improving and replacing anatomical parts of the human body, avoiding the occurrence of adverse reactions in the host organism. Unfortunately, the early failure of implants cannot be currently avoided, since neither a good mixture of mechanical and chemical characteristics of materials nor their biocompatibility has been yet achieved. Bioactive glasses are recognized to be a fine class of bioactive substances for good repair and replacement. BM interact with living bones through the formation of a hydroxyapatite surface layer that is analogous to bones. Bioglasses' composition noticeably affects their biological properties, as does the synthesis method, with the best one being the versatile sol-gel technique, which includes the change of scheme from a 'sol' fluid into a 'gel'. This process is widely used to prepare many materials for biomedical implants (e.g., hip and knee prostheses, heart valves, and ceramic, glassy and hybrid materials to serve as carriers for drug release). Nanoparticles prepared by the sol-gel method are interesting systems for biomedical implementations, and particularly useful for cancer therapy. This review provides many examples concerning the synthesis and characterization of the above-mentioned materials either taken from literature and from recently prepared zirconia/polyethylene glycol (PEG) hybrids, and the corresponding results are extensively discussed.

Linear ß-amino alcohol catalyst anchored on functionalized magnetite nanoparticles for enantioselective addition of dialkylzinc to aromatic aldehydes.

A linear ß-amino alcohol ligand, previously found to be a very efficient catalyst for enantioselective addition of dialkylzinc to aromatic aldehydes, has been anchored on differently functionalized superparamagnetic core-shell magnetite-silica nanoparticles (1a and 1b). Its catalytic activity in the addition of dialkylzinc to aldehydes has been evaluated, leading to promising results, especially in the case of 1b for which the recovery by simple magnetic decantation and reuse was successfully verified.