Strontium-containing mineralized phospholipid coatings improve osseointegration in osteoporotic rats.

Surface treatments play an important role in enhancing the osseointegration of Titanium (Ti) and its alloys. This study introduces a method employing biomimetic hydroxyapatite (Hap) deposition guided by molecularly organized phospholipids, affixed to the metal implant surface. Using the Langmuir-Blodgett technique, phospholipids were deposited onto Ti-screws by using CaCl2 or CaCl2/SrCl2 aqueous solution in the subphase of a Langmuir trough in the target proportion (i.e. 10 and 90 mol% of Sr2+ in relation of Ca2+) followed by immersion in phosphate buffer and in supersaturated simulated body fluid. Coating composition and morphology were evaluated using infrared spectroscopy and scanning electron microscopy, respectively, while contact angle measurements assessed coating wettability and surface energy. Randomized screws were then implanted into the tibias of healthy and osteoporotic female rats (G1: Control-Machined, G2: Hap, G3: HapSr10, G4: HapSr90). Osseointegration, assessed 60 days post-implantation, included reverse torque, fluorochrome area, bone tissue-screw contact area, and linear extent of bone-screw contact. Results, grouped by surface treatment (Machined, Hap, HapSr10, HapSr90), revealed that the deposition of Hap, HapSr10, and HapSr90 resulted in thin and rough coatings composed of hydroxyapatite (Hap) on the screw surface with nanoscale pores. The coatings resulted in increased wettability and surface energy of Ti surfaces. The minerals are chemically similar to natural bone apatite as revealed by FTIR analysis. In vivo analyses indicated higher torque values for strontium-containing surfaces in the osteoporotic group (p = 0.02) and, in the control group superior torque for screw removal on the Hap surface (p = 0.023). Hydroxyapatite-treated surfaces enhance morphology, composition, and reactivity, promoting screw osseointegration in healthy and osteoporotic female rats. The incorporation of strontium into the mineral phase has been proposed to not only stimulate osteoblast activity but also reduce osteoclastic resorption, which may explain the improved outcomes observed here in experimental osteoporotic conditions.

Collagen/κ-Carrageenan-Based Scaffolds as Biomimetic Constructs for In Vitro Bone Mineralization Studies.

Tissue engineering offers attractive strategies to develop three-dimensional scaffolds mimicking the complex hierarchical structure of the native bone. The bone is formed by cells incorporated in a molecularly organized extracellular matrix made of an inorganic phase, called biological apatite, and an organic phase mainly made of collagen and noncollagenous macromolecules. Although many strategies have been developed to replicate the complexity of bone at the nanoscale in vitro, a critical challenge has been to control the orchestrated process of mineralization promoted by bone cells in vivo and replicate the anatomical and biological properties of native bone. In this study, we used type I collagen to fabricate mineralized scaffolds mimicking the microenvironment of the native bone. The sulfated polysaccharide κ-carrageenan was added to the scaffolds to fulfill the role of noncollagenous macromolecules in the organization and mineralization of the bone matrix and cell adhesion. Scanning electron microscopy images of the surface of the collagen/κ-carrageenan scaffolds showed the presence of a dense and uniform network of intertwined fibrils, while images of the scaffolds' lateral sides showed the presence of collagen fibrils with a parallel alignment, which is characteristic of dense connective tissues. MC3T3-E1 osteoblasts were cultured in the collagen scaffolds and were viable after up to 7 days of culture, both in the absence and in the presence of κ-carrageenan. The presence of κ-carrageenan in the collagen scaffolds stimulated the maturation of the cells to a mineralizing phenotype, as suggested by the increased expression of key genes related to bone mineralization, including alkaline phosphatase (Alp), bone sialoprotein (Bsp), osteocalcin (Oc), and osteopontin (Opn), as well as the ability to mineralize the extracellular matrix after 14 and 21 days of culture. Taken together, the results described in this study shed light on the potential use of collagen/κ-carrageenan scaffolds to study the role of the structural organization of bone-mimetic synthetic matrices in cell function.

Influence of Er:YAG laser irradiation on surface properties of Ti-6Al-4V machined and hydroxyapatite coated.

Surface treatment by laser irradiation can change the topography of titanium; however, little is known about the changes it causes when applied to other coatings. This study aimed to evaluate the influence of Er:YAG laser irradiation on the surface properties of titanium-aluminum-vanadium (Ti-6Al-4V) discs. Four Ti-6Al-4V surfaces were evaluated (n = 10): CON-control, machined without surface treatment; LT-machined + laser treatment; HA-hydroxyapatite coating; and LT-HA-hydroxyapatite coating + laser treatment. For the laser treatment, an Er:YAG laser with a wavelength of 2940 nm, a frequency of 10 Hz, and an energy density of 12.8 J/cm2 was used. The morphology of the coating was investigated by scanning electron microscopy and the surface composition by energy-dispersive X-ray spectroscopy. The influence of laser irradiation treatment on roughness and wettability was also evaluated. The Er:YAG laser promoted a significant reduction in the roughness Sa (p < 0.05) and in the contact angle (p = 0.002) of the LT surface compared to the CON surface. On the LT-HA surface, a significant decrease in roughness was observed only for the Rz parameter (p = 0.015) and an increase in the contact angle (p < 0.001) compared to the HA surface. The use of the Er:YAG laser with the evaluated parameters decreased the surface roughness and improved the wetting capacity of machined without surface treatment. In the group with hydroxyapatite coating, the laser influenced the surface roughness only for the parameter Rz and reduced their wetting capacity.

Fabrication and characterization of a bioactive polymethylmethacrylate-based porous cement loaded with strontium/calcium apatite nanoparticles.

Polymethylmethacrylate (PMMA)-based cements are used for bone reparation due to their biocompatibility, suitable mechanical properties, and mouldability. However, these materials suffer from high exothermic polymerization and poor bioactivity, which can cause the formation of fibrous tissue around the implant and aseptic loosening. Herein, we tackled these problems by adding Sr2+ -substituted hydroxyapatite nanoparticles (NPs) and a porogenic compound to the formulations, thus creating a microenvironment suitable for the proliferation of osteoblasts. The NPs resembled the structure of the bone's apatite and enabled the controlled release of Sr2+ . Trends in the X-ray patterns and infrared spectra confirmed that Sr2+ replaced Ca2+ in the whole composition range of the NPs. The inclusion of an effervescent additive reduced the polymerization temperature and lead to the formation of highly porous cement exhibiting mechanical properties comparable to the trabecular bone. The formation of an opened and interconnected matrix allowed osteoblasts to penetrate the cement structure. Most importantly, the gas formation confined the NPs at the surface of the pores, guaranteeing the controlled delivery of Sr2+ within a concentration sufficient to maintain osteoblast viability. Additionally, the cement was able to form apatite when immersed into simulated body fluids, further increasing its bioactivity. Therefore, we offer a formulation of PMMA cement with improved in vitro performance supported by enhanced bioactivity, increased osteoblast viability and deposition of mineralized matrix assigned to the loading with Sr2+ -substituted hydroxyapatite NPs and the creation of an interconnected porous structure. Altogether, our results hold promise for enhanced bone reparation guided by PMMA cements.