A Passive Ankle Dorsiflexion Testing System for an In Vivo Model of Overuse-induced Tendinopathy.

Tendinopathy is a chronic tendon condition that results in pain and loss of function and is caused by repeated overload of the tendon and limited recovery time. This protocol describes a testing system that cyclically applies mechanical loads via passive dorsiflexion to the rat Achilles tendon. The custom-written code consists of pre- and post-cyclic loading measurements to assess the effects of the loading protocol along with the feedback control-based cyclic fatigue loading regimen. We used 25 Sprague-Dawley rats for this study, with 5 rats per group receiving either 500, 1,000, 2,000, 3,600, or 7,200 cycles of fatigue loads. The percentage differences between the pre- and post-cyclic loading measurements of the hysteresis, peak stress, and loading and unloading moduli were calculated. The results demonstrate that the system can induce varying degrees of damage to the Achilles tendon based on the number of loads applied. This system offers an innovative approach to apply quantified and physiological varying degrees of cyclic loads to the Achilles tendon for an in vivo model of fatigue-induced overuse tendon injury.

Successive tendon injury in an in vivo rat overload model induces early damage and acute healing responses.

Introduction: Tendinopathy is a degenerative condition resulting from tendons experiencing abnormal levels of multi-scale damage over time, impairing their ability to repair. However, the damage markers associated with the initiation of tendinopathy are poorly understood, as the disease is largely characterized by end-stage clinical phenotypes. Thus, this study aimed to evaluate the acute tendon responses to successive fatigue bouts of tendon overload using an in vivo passive ankle dorsiflexion system. Methods: Sprague Dawley female rats underwent fatigue overloading to their Achilles tendons for 1, 2, or 3 loading bouts, with two days of rest in between each bout. Mechanical, structural, and biological assays were performed on tendon samples to evaluate the innate acute healing response to overload injuries. Results: Here, we show that fatigue overloading significantly reduces in vivo functional and mechanical properties, with reductions in hysteresis, peak stress, and loading and unloading moduli. Multi-scale structural damage on cellular, fibril, and fiber levels demonstrated accumulated micro-damage that may have induced a reparative response to successive loading bouts. The acute healing response resulted in alterations in matrix turnover and early inflammatory upregulations associated with matrix remodeling and acute responses to injuries. Discussion: This work demonstrates accumulated damage and acute changes to the tendon healing response caused by successive bouts of in vivo fatigue overloads. These results provide the avenue for future investigations of long-term evaluations of tendon overload in the context of tendinopathy.

A passive ankle dorsiflexion testing system to assess mechanobiological and structural response to cyclic loading in rat Achilles tendon.

Tendinopathy is thought to be caused by repeated overload of the tendon with insufficient recovery time, leading to an inadequate healing response and incomplete recovery of preinjury material strength and function. The etiology of tendinopathy induced by mechanical load is being explored with a variety of mechanical load scenarios in small animals. This study establishes a testing system that applies passive ankle dorsiflexion to a rat hindlimb, estimates the force applied to the tendon during cyclic loading and enables the assessment of subsequent structural and biological changes. We demonstrated that the system had no drift in the applied angle, and the registered maximum angle and torque inputs and outputs were consistent between tests. We showed that cyclic loading decreased hysteresis and loading and unloading moduli with increasing cycles applied to the tendon. Histology showed gross changes to tendon structure. This work establishes a system for passively loading the rat Achilles tendon in-vivo in a physiological manner, facilitating future studies that will explore how mechanics, structure, and biology are altered by mechanical repetitive loading.

Effect of intraarticular pressure on glenohumeral kinematics during a simulated abduction motion: a cadaveric study.

BACKGROUND: The current understanding of glenohumeral joint stability is defined by active restrictions and passive stabilizers including naturally-occurring negative intraarticular pressure. Cadaveric specimens have been used to evaluate the role of intraarticular pressure on joint stability, although, while the shoulder's negative intraarticular pressure is universally acknowledged, it has been inconsistently accounted for. HYPOTHESIS: During continuous, passive humeral abduction, releasing the native intraarticular pressure increases joint translation, and restoring this pressure decreases joint translations. STUDY DESIGN: Descriptive Laboratory Study. METHODS: A validated shoulder testing system was used to passively abduct the humerus in the scapular plane and measure joint translations for seven (n = 7) cadaveric specimens. The pressure within the glenohumeral joint was measured via a 25-gauge needle during passive abduction of the arm, which was released and subsequently restored. During motion, the rotator cuff muscles were loaded using stepper motors in a force feedback loop and electromagnetic sensors were used to continuously measure the position of the humerus and scapula. Joint translation was defined according to the instant center of rotation of the glenohumeral head according to the recommendations by the International Society of Biomechanics. RESULTS: Area under the translation versus abduction angle curve suggests that releasing the pressure within the capsule results in significantly less posterior translation of the glenohumeral head as compared to intact (85-90˚, p < 0.05). Posterior and superior translations were reduced after 70˚ of abduction when the pressure within the joint was restored. CONCLUSION: With our testing system employing a smooth continuous passive motion, we were able to show that releasing intraarticular pressure does not have a major effect on the path of humeral head motion during glenohumeral abduction. However, both violating the capsule and restoring intraarticular pressure after releasing alter glenohumeral translations. Future studies should study the effect of simultaneous external rotation and abduction on the relationship between joint motion and IAP, especially in higher degrees of abduction. CLINICAL RELEVANCE: Thoroughly simulating the glenohumeral joint environment in the cadaveric setting may strengthen the conclusions that can be translated from this setting to the clinic.

Combined MPFL reconstruction and tibial tuberosity transfer avoid focal patella overload in the setting of elevated TT-TG distances.

PURPOSE: Objectives are (1) to evaluate the biomechanical effect of isolated medial patellofemoral ligament (MPFL) reconstruction in the setting of increased tibial tuberosity-trochlear groove distance (TTTG), in terms of patella contact pressures, contact area and lateral displacement; (2) to describe the threshold of TTTG up to which MPFL reconstruction should be performed alone or in combination with tibial tuberosity transfer. METHODS: A finite element model of the knee was developed and validated. The model was modified to simulate isolated MPFL reconstruction, tibial tuberosity transfer and MPFL reconstruction combined with tibial tuberosity transfer for patella malalignment. Two TT-TG distances (17 mm and 22 mm) were simulated. Patella contact pressure, contact area and lateral displacement were analysed. RESULTS: Isolated MPFL reconstruction, at early degrees of flexion, restored normal patella contact pressure when TTTG was 17 mm, but not when TTTG was 22 mm. After 60° of flexion, the TTTG distance was the main factor influencing contact pressure. Isolated MPFL reconstruction for both TTTG 17 mm and 22 mm showed higher contact area and lower lateral displacement than normal throughout knee flexion. Tibial tuberosity transfer, at early degrees of flexion, reduced the contact pressure, but did not restore the normal contact pressure. After 60° of flexion, the TTTG distance was the main factor influencing contact pressure. Tibial tuberosity transfer maintained lower contact area than normal throughout knee flexion. The lateral displacement was higher than normal between 0° and 30° of flexion (< 0.5 mm). MPFL reconstruction combined with tibial tuberosity transfer produced the same contact mechanics and kinematics of the normal condition. CONCLUSION: This study highlights the importance of considering to correct alignment in lateral tracking patella to avoid focal patella overload. Our results showed that isolated MPFL reconstruction corrects patella kinematics regardless of TTTG distance. However, isolated MPFL reconstruction would not restore normal patella contact pressure when TTTG is 22 mm. For TTTG 22 mm, the combined procedure of MPFL reconstruction and tibial tuberosity transfer provided an adequate patellofemoral contact mechanics and kinematics, restoring normal biomechanics. This data supports the use of MPFL reconstruction when the patient has normal alignment and the use of combined MPFL reconstruction and tibial tuberosity transfer in patients with elevated TT-TG distances to avoid focal overload.

A Validated Three-Dimensional, Heterogenous Finite Element Model of the Rotator Cuff and The Effects of Collagen Orientation.

Continuum mechanics-based finite element models of the shoulder aim to quantify the mechanical environment of the joint to aid in clinical decision-making for rotator cuff injury and disease. These models allow for the evaluation of the internal loading of the shoulder, which cannot be measured in-vivo. This study uses human cadaveric rotator cuff samples with surface tendon strain estimates, to validate a heterogeneous finite element model of the supraspinatus-infraspinatus complex during various load configurations. The computational model was considered validated when the absolute difference in average maximum principal strain for the articular and bursal sides for each load condition estimated by the model was no greater than 3% compared to that measured in the biomechanical study. The model can predict the strains for varying infraspinatus loads allowing for the study of load sharing between these two tightly coordinated tendons. The future goal is to use the modularity of this validated model to study the initiation and propagation of rotator cuff tear and other rotator cuff pathologies to ultimately improve care for rotator cuff tear patients.

Lateral retinacular release in concordance with medial patellofemoral ligament reconstruction in patients with recurrent patellar instability: A computational model.

BACKGROUND: The aim of this study was to develop and validate a finite element (FE) model of the patellofemoral joint to analyze the biomechanics of lateral retinacular release after medial patellofemoral ligament (MPFL) reconstruction in patellar malalignment (increased tibial tubercle-trochlear groove distance (TT-TG)). We hypothesized that lateral retinacular release is not appropriate in patellar instability addressed by MPFL reconstruction due to decreased lateral stability and inappropriate adjustment in patellofemoral contact pressures. METHODS: A FE in-silico model of the patellofemoral joint was developed and validated. The model was used analyze the effect of lateral retinacular release in association with MPFL reconstruction on patellofemoral contact pressures, contact area, and lateral patellar displacement during knee flexion. RESULTS: MPFL reconstruction alone results in restoration of patellofemoral contact pressures throughout the entire range of motion (0-90°), mimicking the results from healthy condition. The addition of the lateral retinacular release to the MPFL reconstruction resulted in significant reductions in both patellofemoral contact pressure and contact area. Lateral retinacular release resulted in more lateral patellar displacement during the mid-flexion knee range of motion. CONCLUSIONS: Combination of lateral retinacular release with MPFL reconstruction in patients with increased TT-TG is not recommended as MPFL reconstruction alone for first-line management of recurrent patellar instability offers a greater biomechanical advantage and restoration of contact forces to resemble that of the healthy knee. The presented biomechanical data outlines the effect of concomitant MPFL reconstruction and lateral retinacular release to help guide surgical planning for patients with recurrent patellar instability due to malalignment.

Minimally invasive, sustained-release relaxin-2 microparticles reverse arthrofibrosis.

Substantial advances in biotherapeutics are distinctly lacking for musculoskeletal diseases. Musculoskeletal diseases are biomechanically complex and localized, highlighting the need for novel therapies capable of addressing these issues. All frontline treatment options for arthrofibrosis, a debilitating musculoskeletal disease, fail to treat the disease etiology-the accumulation of fibrotic tissue within the joint space. For millions of patients each year, the lack of modern and effective treatment options necessitates surgery in an attempt to regain joint range of motion (ROM) and escape prolonged pain. Human relaxin-2 (RLX), an endogenous peptide hormone with antifibrotic and antifibrogenic activity, is a promising biotherapeutic candidate for musculoskeletal fibrosis. However, RLX has previously faltered through multiple clinical programs because of pharmacokinetic barriers. Here, we describe the design and in vitro characterization of a tailored drug delivery system for the sustained release of RLX. Drug-loaded, polymeric microparticles released RLX over a multiweek time frame without altering peptide structure or bioactivity. In vivo, intraarticular administration of microparticles in rats resulted in prolonged, localized concentrations of RLX with reduced systemic drug exposure. Furthermore, a single injection of RLX-loaded microparticles restored joint ROM and architecture in an atraumatic rat model of arthrofibrosis with clinically derived end points. Finally, confirmation of RLX receptor expression, RXFP1, in multiple human tissues relevant to arthrofibrosis suggests the clinical translational potential of RLX when administered in a sustained and targeted manner.

Imaging of traumatic shoulder injuries - Understanding the surgeon's perspective.

Imaging plays a key role in the assessment and management of traumatic shoulder injuries, and it is important to understand how the imaging details help guide orthopedic surgeons in determining the role for surgical treatment. Imaging is also crucial in preoperative planning, the longitudinal assessment after surgery and the identification of complications after treatment. This review discusses the mechanisms of injury, key imaging findings, therapeutic options and associated complications for the most common shoulder injuries, tailored to the orthopedic surgeon's perspective.

Lateral release associated with MPFL reconstruction in patients with acute patellar dislocation.

OBJECTIVE: Medial patellofemoral ligament (MPFL) injury occurs in the majority of the cases of acute patellar dislocation. The role of concomitant lateral retinaculum release with MPFL reconstruction is not clearly understood. Even though the lateral retinaculum plays a role in both medial and lateral patellofemoral joint stability in MPFL intact knees, studies have shown mixed clinical outcomes following its release during MPFL reconstruction surgery. Better understanding of the biomechanical effects of the release of the lateral retinaculum during MPFL reconstruction is warranted. We hypothesize that performing a lateral release concurrent with MPFL reconstruction will disrupt the patellofemoral joint biomechanics and result in lateral patellar instability. METHODS: A previously developed and validated finite element (FE) model of the patellofemoral joint was used to understand the effect of lateral retinaculum release following MPFL reconstruction. Contact pressure (CP), contact area (CA) and lateral patellar displacement were recorded. abstract. RESULTS: FE modeling and analysis demonstrated that lateral retinacular release following MPFL reconstruction with tibial tuberosity-tibial groove distance (TT-TG) of 12 mm resulted in a 39% decrease in CP, 44% decrease in CA and a 20% increase in lateral patellar displacement when compared to a knee with an intact MPFL. In addition, there was a 45% decrease in CP, 44% decrease in CA and a 21% increase in lateral displacement when compared to a knee that only had an MPFL reconstruction. CONCLUSION: This FE-based analysis exhibits that concomitant lateral retinaculum release with MPFL reconstruction results in decreased PF CA, CP and increased lateral patellar displacement with increased knee flexion, which may increase the risk of patellar instability.

Recommended Musculoskeletal and Sports Ultrasound Terminology: A Delphi-Based Consensus Statement.

OBJECTIVES: The current lack of agreement regarding standardized terminology in musculoskeletal and sports ultrasound presents challenges in education, clinical practice, and research. This consensus was developed to provide a reference to improve clarity and consistency in communication. METHODS: A multidisciplinary expert panel was convened consisting of 18 members representing multiple specialty societies identified as key stakeholders in musculoskeletal and sports ultrasound. A Delphi process was used to reach consensus which was defined as group level agreement >80%. RESULTS: Content was organized into seven general topics including: 1) General Definitions, 2) Equipment and Transducer Manipulation, 3) Anatomic and Descriptive Terminology, 4) Pathology, 5) Procedural Terminology, 6) Image Labeling, and 7) Documentation. Terms and definitions which reached consensus agreement are presented herein. CONCLUSIONS: The historic use of multiple similar terms in the absence of precise definitions has led to confusion when conveying information between colleagues, patients, and third-party payers. This multidisciplinary expert consensus addresses multiple areas of variability in diagnostic ultrasound imaging and ultrasound-guided procedures related to musculoskeletal and sports medicine.

Recommended musculoskeletal and sports ultrasound terminology: a Delphi-based consensus statement.

The current lack of agreement regarding standardised terminology in musculoskeletal and sports ultrasound presents challenges in education, clinical practice and research. This consensus was developed to provide a reference to improve clarity and consistency in communication. A multidisciplinary expert panel was convened consisting of 18 members representing multiple specialty societies identified as key stakeholders in musculoskeletal and sports ultrasound. A Delphi process was used to reach consensus, which was defined as group level agreement of >80%. Content was organised into seven general topics including: (1) general definitions, (2) equipment and transducer manipulation, (3) anatomical and descriptive terminology, (4) pathology, (5) procedural terminology, (6) image labelling and (7) documentation. Terms and definitions which reached consensus agreement are presented herein. The historic use of multiple similar terms in the absence of precise definitions has led to confusion when conveying information between colleagues, patients and third-party payers. This multidisciplinary expert consensus addresses multiple areas of variability in diagnostic ultrasound imaging and ultrasound-guided procedures related to musculoskeletal and sports medicine.

A validated algorithm using current literature to judge the appropriateness of anatomic total shoulder arthroplasty utilizing the RAND/UCLA appropriateness method.

BACKGROUND: Currently, appropriateness criteria evaluating when to perform total shoulder arthroplasty (TSA) is lacking. In the absence of society guidelines and limited quality evidence, the RAND/University California in Los Angeles (UCLA) method provides a suitable alternative to evaluate appropriateness and assist in clinical decision making. Given the rise in utilization, appropriateness criteria for TSA have the potential to be an extremely powerful tool for improving quality of care and controlling costs. Thus, the goal of this study was to test explicit criteria to assess the appropriateness of TSA decision making using the RAND/UCLA appropriateness method. METHODS: A review of recent scientific literature to gather available evidence about the use, effectiveness, efficiency, and the risks involved in surgical intervention was performed by a shoulder/elbow fellowship trained physician. Based on pertinent variables including age, rotator cuff status, previous surgical management, mobility, symptomatology, and imaging classifications, 186 clinical scenarios were created. Appropriateness criteria for TSA were developed using a modified Delphi method with a panel consisting of American Shoulder and Elbow Surgeons (ASES) members. A second panel of ASES members rated the same scenarios, with reliability testing performed to compare groups. RESULTS: Panel members reached agreement in 40 (64%) indications. TSA was appropriate in 15 (24%) of indications. For patients with severe symptomatology, TSA was often appropriate for patients aged <75 years and inconclusive or inappropriate for patients aged >75 years. Among patients aged <65 years, TSA varied between appropriate and inconclusive, often dependent on Walch classification. For patients with moderate symptomatology, TSA was inappropriate or inconclusive for patients aged <65 or >75 years. When compared to the second panel's results, moderate agreement was obtained with a weighted kappa statistic of 0.56. CONCLUSIONS: Using the RAND/UCLA method, ASES members created an appropriateness decision tree for pertinent patient variables. This presents the data in a manner that streamlines the clinical decision-making process and allows for rapid and more reliable determination of appropriateness for practitioners. The decision tree is based on a combination of clinical experience from high-volume ASES-member surgeons and a comprehensive review of current evidence. This tool can be used as part of a broader set of factors, including individual patient characteristics, prior studies, and expert opinion, to inform clinical decision making, improve quality of care, and control costs.

Lateral Release With Tibial Tuberosity Transfer Alters Patellofemoral Biomechanics Promoting Multidirectional Patellar Instability.

PURPOSE: The purpose of this study was to develop and validate a finite element (FE) model of the patellofemoral (PF) joint to characterize patellofemoral instability, and to highlight the effect of lateral retinacular release in combination with tibial tuberosity transfer with respect to contact pressures (CP), contact area (CA), and kinematics during knee flexion. METHODS: A comprehensive, dynamic FE model of the knee joint was developed and validated through parametric comparison of PF kinematics, CP, and CA between FE simulations and in vitro, cadaveric experiments. Using this FE model, we characterized the effect of patellar instability, lateral retinacular release (LR), and tibial tuberosity transfer (TTT) in the setting of medial patellofemoral ligament injury during knee flexion. RESULTS: There was a high level of agreement in CP, CA, lateral patellar displacement, anterior patellar displacement, and superior patellar displacement between the FE model and the in vitro data (P values 0.19, 0.16, 0.81, 0.10, and 0.36, respectively). Instability conditions demonstrated the greatest CP compared to all of the other conditions. During all degrees of flexion, TTT and concomitant lateral release (TTT + LR) decreased CP significantly. TTT alone shows a consistently lower CA compared to nonrelease conditions with subsequent lateral release further decreasing CA. CONCLUSIONS: The results of this study demonstrate that the FE model described reliably simulates PF kinematics and CP within 1 SD in uncomplicated cadaveric specimens. The FE model is able to show that tibial tubercle transfer in combination with lateral retinacular release markedly decreases patellofemoral CP and CA and increases lateral patellar displacement that may decrease bony stabilization of the patella within the trochlear groove and promote lateral patellar instability. CLINICAL RELEVANCE: The goal of surgical correction for patellar instability focuses on reestablishing normal PF kinematics. By developing an FE model that can demonstrate patient PF kinematics and the results of different surgical approaches, surgeons may tailor their treatment to the best possible outcome. Of the surgical approaches that have been described, the biomechanical effects of the combination of TTT with lateral retinacular release have not been studied. Thus, the FE analysis will help shed light on the effect of the combination of TTT with lateral retinacular release on PF kinematics.

Conservative versus accelerated rehabilitation after rotator cuff repair: a systematic review and meta-analysis.

BACKGROUND: The purpose of this systematic review and meta-analysis is to compare the conservative and accelerated rehabilitation protocols in patients who underwent arthroscopic rotator cuff repair in terms of clinical outcomes and range of motions at 3, 6, 12, and 24-month follow-up. METHODS: According to PRISMA guidelines, a systematic review of the literature was performed. For each included article, the following data has been extracted: authors, year, study design, level of evidence, demographic characteristics, follow-up, clinical outcomes, range of motions, and retear events. A meta-analysis was performed to compare accelerated versus conservative rehabilitation protocols after arthroscopic rotator cuff repair. The retear rate, postoperative Constant-Murley score and range of motions at 3, 6, 12, and 24 months of follow-up were the outcomes measured. RESULTS: The search strategy yielded 16 level I-II clinical studies. A total of 1424 patients, with 732 patients and 692 in the accelerated and conservative group, were included. The average age (mean ± standard deviation) was 56.1 ± 8.7 and 56.6 ± 9 in the accelerated and conservative group. The mean follow-up was 12.5 months, ranging from 2 to 24 months. The meta-analysis showed no statistically significant differences in terms of retear rate between the groups (P = 0.29). The superiority of the accelerated group was demonstrated in terms of external rotation (P < 0.05) at 3-month follow-up; in terms of forward elevation, external rotation, abduction (P < 0.05), but not in terms of Constant-Murley score at 6-month follow-up; in terms of forward elevation (P < 0.05) at 12-month follow-up. No significant differences between the two group were highlighted at 24-month follow-up. CONCLUSIONS: No statistically significant differences in the retear rate among the accelerated and conservative group have been demonstrated. On the other hand, statistically and clinically significant differences were found in terms of external rotation at 3 and 6 months of follow-up in favour of the accelerated group. However, no differences between the two groups were detected at 24 months follow-up.

Evolution of knowledge on meniscal biomechanics: a 40 year perspective.

BACKGROUND: Knowledge regarding the biomechanics of the meniscus has grown exponentially throughout the last four decades. Numerous studies have helped develop this knowledge, but these studies have varied widely in their approach to analyzing the meniscus. As one of the subcategories of mechanical phenomena Medical Subject Headings (MeSH) terms, mechanical stress was introduced in 1973. This study aims to provide an up-to-date chronological overview and highlights the evolutionary comprehension and understanding of meniscus biomechanics over the past forty years. METHODS: A literature review was conducted in April 2021 through PubMed. As a result, fifty-seven papers were chosen for this narrative review and divided into categories; Cadaveric, Finite element (FE) modeling, and Kinematic studies. RESULTS: Investigations in the 1970s and 1980s focused primarily on cadaveric biomechanics. These studies have generated the fundamental knowledge basis for the emergence of FE model studies in the 1990s. As FE model studies started to show comparable results to the gold standard cadaveric models in the 2000s, the need for understanding changes in tissue stress during various movements triggered the start of cadaveric and FE model studies on kinematics. CONCLUSION: This study focuses on a chronological examination of studies on meniscus biomechanics in order to introduce concepts, theories, methods, and developments achieved over the past 40 years and also to identify the likely direction for future research. The biomechanics of intact meniscus and various types of meniscal tears has been broadly studied. Nevertheless, the biomechanics of meniscal tears, meniscectomy, or repairs in the knee with other concurrent problems such as torn cruciate ligaments or genu-valgum or genu-varum have not been extensively studied.

Tendinopathy and tendon material response to load: What we can learn from small animal studies.

Tendinopathy is a debilitating disease that causes as much as 30% of all musculoskeletal consultations. Existing treatments for tendinopathy have variable efficacy, possibly due to incomplete characterization of the underlying pathophysiology. Mechanical load can have both beneficial and detrimental effects on tendon, as the overall tendon response depends on the degree, frequency, timing, and magnitude of the load. The clinical continuum model of tendinopathy offers insight into the late stages of tendinopathy, but it does not capture the subclinical tendinopathic changes that begin before pain or loss of function. Small animal models that use high tendon loading to mimic human tendinopathy may be able to fill this knowledge gap. The goal of this review is to summarize the insights from in-vivo animal studies of mechanically-induced tendinopathy and higher loading regimens into the mechanical, microstructural, and biological features that help characterize the continuum between normal tendon and tendinopathy. STATEMENT OF SIGNIFICANCE: This review summarizes the insights gained from in-vivo animal studies of mechanically-induced tendinopathy by evaluating the effect high loading regimens have on the mechanical, structural, and biological features of tendinopathy. A better understanding of the interplay between these realms could lead to improved patient management, especially in the presence of painful tendon.

Imaging of Acute Shoulder Trauma.

Acute injuries to the shoulder girdle are common and frequently encountered by the practicing radiologist. The type of injury is highly dependent on the age of the patient and mechanism of trauma with injuries occurring at the site of greatest mechanical weakness. In this review, we discuss the main clinical features and key imaging findings for the most common shoulder injuries. For each injury, we also provide a section on the important features that the orthopedic surgeon needs to know in order to guide surgical versus nonsurgical management.

Comparison of Patellofemoral Kinematics and Stability After Medial Patellofemoral Ligament and Medial Quadriceps Tendon-Femoral Ligament Reconstruction.

BACKGROUND: There is a lack of evidence regarding the optimum extensor-sided fixation method for medial patellofemoral ligament (MPFL) reconstruction. There is increased interest in avoiding patellar drilling via soft tissue-only fixation to the distal quadriceps, thus reconstructing the medial quadriceps tendon-femoral ligament (MQTFL). The biomechanical implications of differing extensor-sided fixation constructs remain unknown. HYPOTHESIS: The null hypothesis was there would be no differences between traditional MPFL reconstruction and MQTFL reconstruction with respect to resistance to lateral translation, patellar position, or patellofemoral contact pressures. STUDY DESIGN: Controlled laboratory study. METHODS: Nine adult knee specimens were mounted on a jig that applied static, physiologic loads to the quadriceps tendons. Patellar position and orientation, knee flexion angle, and patellofemoral pressure were recorded at 8 different flexion angles between 0° and 110°. Additionally, a lateral patellar excursion test was conducted wherein a load was applied directly to the patella in the lateral direction with the knee at 30° of flexion and subjected to 2-N quadriceps loads. Testing was conducted under 4 conditions: intact, transected MPFL, MQTFL reconstruction, and MPFL reconstruction. For MQTFL reconstruction, the surgical technique established by Fulkerson was employed. For MPFL reconstruction, a traditional technique was utilized. RESULTS: The patellar excursion test showed no significant difference between the MQTFL and intact states with respect to lateral translation. MPFL reconstruction led to significantly less lateral translation (P < .05) than all other states. There were no significant differences between MPFL and MQTFL reconstructions with respect to peak patellofemoral contact pressure. MPFL and MQTFL reconstructions both resulted in increased internal rotation of the patella with the knee in full extension. CONCLUSION: Soft tissue-only extensor-sided fixation to the distal quadriceps (MQTFL) during patella stabilization appears to re-create native stability in this time 0 cadaver model. Fixation to the patella (MPFL) was associated with increased resistance to lateral translation. CLINICAL RELEVANCE: Evolving anatomic knowledge and concern for patellar fracture has led to increased interest in MQTFL reconstruction. Both MQTFL and MPFL reconstructions restored patellofemoral stability to lateral translation without increasing contact pressures under appropriate graft tensioning, with MQTFL more closely restoring native resistance to lateral translation at the time of surgery.

Effect of rotator cuff muscle activation on glenohumeral kinematics: A cadaveric study.

Healthy shoulder function requires the coordination of the rotator cuff muscles to maintain the humeral head's position in the glenoid. While glenohumeral stability has been studied in various settings, few studies have characterized the effect of dynamic rotator cuff muscle loading on glenohumeral translation during shoulder motion. We hypothesize that dynamic rotator cuff muscle activation decreases joint translation during continuous passive abduction of the humerus in a cadaveric model of scapular plane glenohumeral abduction. The effect of different rotator cuff muscle activity on glenohumeral translation was assessed using a validated shoulder testing system. The Dynamic Load profile is a novel approach, based on musculoskeletal modeling of human subject motion. Passive humeral elevation in the scapular plane was applied via the testing system arm, while the rotator cuff muscles were activated according to the specified force profiles using stepper motors and a proportional control feedback loop. Glenohumeral translation was defined according to the International Society of Biomechanics. The Dynamic load profile minimized superior translation of the humeral head relative to the conventional loading profiles. The total magnitude of translation was not significantly different (0.805) among the loading profiles suggesting that the compressive forces from the rotator cuff primarily alter the direction of humeral head translation, not the magnitude. Rotator cuff muscle loading is an important element of cadaveric shoulder studies that must be considered to accurately simulate glenohumeral motion. A rotator cuff muscle activity profile based on human subject muscle activity reduces superior glenohumeral translation when compared to previous RC loading profiles.