Structural, Viscoelastic, and Electrochemical Characteristics of Self-Assembled Amphiphilic Comblike Copolymers in Aqueous Solutions.

Self-assembly in aqueous solutions of an amphiphilic comblike polyelectrolyte (80C12) that consists of a polystyrene (PS) backbone onto which quaternary ammonium pendant moieties have been grafted has been investigated by light scattering and cryo-transmission electron microscopy measurements in the presence of KCl and methylviologen dication (MV2+) under conditions mimicking those for electrochemical measurements. Polymer chains self-assemble within branched cylindrical micelles that display viscoelastic properties, characterized by a relaxation time of 4 s. To tune this time, 80C12 was mixed with a polyoxyethylene nonionic surfactant (Brij C12E10). Relatively increasing the amount of the latter leads to a decrease in the relaxation time of the 80C12 solution. Correlatively, electrochemical experiments with a rotating disk electrode show a transition of the mass transport rate, which deviates from the classical Newtonian behavior in the same velocity domain. This result generalizes what has been already observed with solutions of linear polymers of high molecular weight and wormlike micelles based on surfactants subjected to elongational deformations. Moreover, the critical times derived from rheological and electrochemical experiments display the same trend.

Assessments of the Effect of Increasingly Severe Cathodic Pretreatments on the Electrochemical Activity of Polycrystalline Boron-Doped Diamond Electrodes.

The electrochemical response of many redox species on boron-doped diamond (BDD) electrodes can be strongly dependent on the type of chemical termination on their surface, hydrogen (HT-BDD) or oxygen (OT-BDD). For instance, on an HT-BDD electrode the [Fe(CN)6](3-/4-) redox system presents a reversible voltammetric behavior, whereas the oxidation overpotential of ascorbic acid (AA) is significantly decreased. Moreover, the electrochemical activity of BDD electrodes can be significantly affected by electrochemical pretreatments, with cathodic pretreatments (CPTs) leading to redox behaviors associated with HT-BDD. Here we report on the effect of increasingly severe CPTs on the electrochemical activity of a highly doped BDD electrode, assessed with the [Fe(CN)6](3-/4-) and AA redox probes, and on the atomic bonding structure on the BDD surface, assessed by XPS. The hydrogenation level of the BDD surface was increased by CPTs, leading to decreases of the total relative level of oxidation of the BDD surface of up to 36%. Contrary to what is commonly assumed, we show that BDD surfaces do not need to be highly hydrogenated to ensure that a reversible voltammetric behavior is obtained for Fe(CN)6](3-/4-); after a CPT, this was attained even when the total relative level of oxidation on the BDD surface was about 15%. At the same time, the overpotential for AA oxidation was confirmed as being very sensitive to the level of oxidation of the BDD surface, a behavior that might allow the use of AA as a secondary indicator of the relative atomic bonding structure on the BDD surface.

Determination of the isomeric forms proportion of fluorogenic naphthalene-2,3-dicarboxaldehyde in a binary mixture of water:methanol using electrochemical methods.

The electrochemical response of the fluorogenic label naphthalene-2,3-dicarboxyaldehyde (NDA) in a binary mixture of water/methanol was characterized with cyclic voltammetry (CV) and differential pulse voltammetry (DPV) electrochemical techniques. Naphthalene-2,3-dicarboxyaldehyde does exist in three isomeric forms in aqueous solution: the unhydrated dialdehyde (DA), the acyclic monohydrated (MA) and the cyclic hemiacetal (HAC). The study underlines that the proportion of each of them varies according to the working pH. At low and high pH, the dialdehyde form is in larger proportion than the acyclic monohydrated form. Conversely at intermediate pH, the concentration of the acyclic form is in greater proportion than the dialdehyde form. These results allowed us to determine the optimal pH of 9 for which the labeling of biomolecules could be more efficient due to the base catalyzed regeneration of the unhydrated form. At this pH, the data processing from the analysis of measured currents and estimation of diffusion coefficients of each form according to the semi-empirical models of Wilke-Chang, Scheibel, Reddy-Doraiswamy and Lusis-Ratcliff allowed us to obtain the concentration of dialdehyde (0.28 mM), acyclic monohydrated (0.57 mM) and cyclic hemiacetal monohydrated (0.15 mM) forms starting from 1mM naphthalene-2,3-dicarboxyaldehyde.

Improved electrochemical detection of a transthyretin synthetic peptide in the nanomolar range with a two-electrode system integrated in a glass/PDMS microchip.

An alternative to a three-electrode set-up for electrochemical detection and analysis in microfluidic chips is described here. The design of the electrochemical sensor consists of the surface of the glass substrate covered with a PDMS block which bears the microfluidic channels. A band microelectrode which acts as a working electrode surrounded by a large counter electrode is obtained at the micrometric level to propose a simple and efficient sensing area for on-a-chip analysis. The counter-electrode with a surface area about 22-fold greater than the working-microelectrode can also be considered as a pseudo reference since its current density is low and thus limits the potential variations around the rest potential. To this purpose, the [Fe(III)(CN)6]³â»/[Fe(II)(CN)6]4⁻ redox couple was used in order to set a reference potential at 0 V since both electrodes were platinum. The electrochemical microchip performance was characterized using differential pulse voltammetric (DPV) detection and quantification of the optically multi-labelled transthyretin synthetic peptide mimicking a tryptic fragment of interest for the diagnosis of familial transthyretin amyloidosis (ATTR). The limit of detection of the peptide by the working microelectrode was 25 nM, a value 100-fold lower than the one reported with conventional capillary electrophoresis coupled with laser-induced fluorescence under the same analytical conditions.

Investigating of labelling and detection of transthyretin synthetic peptide derivatized with naphthalene-2,3-dicarboxaldehyde.

Labelling and detection of a synthetic peptide (PN) mimicking a tryptic fragment of interest for the diagnosis of familial amyloidal polyneuropathy have been investigated optically and electrochemically. We decided to covalently label naphtalene-2,3-dicarboxyaldehyde (NDA), a fluorogenic and electroactive molecule on PN. First, the optimization of the labelling chemical reaction was performed by capillary electrophoresis coupled with laser induced fluorescence detection (CE-LIF). The analytical parameters such as separation efficiency and peak area were considered to propose this optimized derivatization reaction. The results obtained allowed us to establish the pH and ionic strength of the derivatization buffer, the molar ratio between NDA and PN and the reaction time of the labelling. Optimal conditions are obtained when [NDA]/[PN]=40, buffer pH of 9, buffer ionic strength of 70 mM and reaction time of 15 min. Second, differential pulse voltammetry (DPV) and cyclic voltammetry (CV) were also used to characterize NDA-labelled PN and different electroinactive amino acids (histidine, lysine, serine, threonine) which are in the PN sequence. The electrochemical detection experiments demonstrated that the labelled biomolecules could be also easily detected at low concentration. Moreover, the derivatization reaction could be followed to describe more precisely the labelling process of these biomolecules. Optimal conditions for labelling are obtained when [NDA]total/[CN(-)] ratio =1 and [NDA]total/[amino acid or peptide]=100 with a buffer having a pH=9 on a glassy carbon electrode. In all cases, an obvious oxidation peak for the N-2-substituted-1-cyanobenz-[f]-isoindole derivative (CBI) has been observed at 0.5-0.7 V/SCE. The multi-labelling of PN and lysine were shown with DPV. We presumed this result to occur because of the shouldered shape of the DPV peak shape. These experiments confirm that NDA can be used as a derivative agent for PN, allowing for electrochemical and fluorescence detections with a limit of detection of labelled PN estimated at 0.2 µM and 5 µM, respectively.

Amorphous carbon nitride as an alternative electrode material in electroanalysis: simultaneous determination of dopamine and ascorbic acid.

Boron-doped diamond (BDD) films are excellent electrode materials, whose electrochemical activity for some analytes can be tuned by controlling their surface termination, most commonly either to predominantly hydrogen or oxygen. This tuning can be accomplished by e.g. suitable cathodic or anodic electrochemical pretreatments. Recently, it has been shown that amorphous carbon nitride (a-CNx) films may present electrochemical characteristics similar to those of BDD, including the influence of surface termination on their electrochemical activity toward some analytes. In this work, we report for the first time a complete electroanalytical method using an a-CNx electrode. Thus, an a-CNx film deposited on a stainless steel foil by DC magnetron sputtering is proposed as an alternative electrode for the simultaneous determination of dopamine (DA) and ascorbic acid (AA) in synthetic biological samples by square-wave voltammetry. The obtained results are compared with those attained using a BDD electrode. For both electrodes, a same anodic pretreatment in 0.1 mol L(-1) KOH was necessary to attain an adequate and equivalent separation of the DA and AA oxidation potential peaks of about 330 mV. The detection limits obtained for the simultaneous determination of these analytes using the a-CNx electrode were 0.0656 µmol L(-1) for DA and 1.05 µmol L(-1) for AA, whereas with the BDD electrode these values were 0.283 µmol L(-1) and 0.968 µmol L(-1), respectively. Furthermore, the results obtained in the analysis of the analytes in synthetic biological samples were satisfactory, attesting the potential application of the a-CNx electrode in electroanalysis.

Computational study of velocity profile obtained in microfluidic channel bearing a fluidic transistor: toward highly resolved electrophoretic separation.

The present work is a computational study of velocity profiles in microfluidic channels bearing field flow effect transistors (FFET). In particular, this work investigates perturbations and distortions of the sample band during electrophoretic transport in a rectangular separation channel. The EOF heterogeneity and its induced pressure render the predictions of the analytical performances rather complex. In this context, we propose a systematic numerical inquiry that focuses on the distribution of the velocities for several geometries and EOF modulations. We compare the calculated parabolic velocity profiles to the bare glass microchips. Here, the reported parabolic velocity profiles are coherent with recent experimental results that have been published elsewhere. From the presented equations, in such active hybrid microfluidic chip that integrates a FFET gate layer, separation can be optimized by playing on the gate coverage ratio. The flow fields obtained from analytical models allow further investigations about the efficiency and resolution during electrophoresis. The resulting induced pressure gradient and the associated band broadening underline the need to optimize the resolution in the detriment of the efficiency in such active microfluidic chips.

Photocurrent generation in carbon nitride and carbon nitride/conjugated polymer composites.

The semiconductor and photovoltaic properties of carbon nitride (CNx) thin films prepared using a reactive magnetron cathodic sputtering technique were investigated both individually and as composites with an organic conjugated polymer, poly(2,2'-bithiophene) (PBT). The CNx films showed an increasing thickness as the deposition power and/or nitrogen content in the gas mixture increase. At low nitrogen content and low deposition power (25-50 W), the film structure was dominated by the abundance of the graphitic sp(2) regions, whereas at higher nitrogen contents and magnetron power CNx films started to demonstrate semiconductor properties, as evidenced by the occurrence of photoconductivity and the development of a space charge region. However, CNx films alone did not show any reproducible photovoltaic properties. The situation changed, however, when CNx was deposited onto conjugated PBT substrates. In this configuration, CNx was found to function as an acceptor material improving the photocurrent generation both in solution and in solid state photovoltaic devices, with the external quantum efficiencies reaching 1% at high nitrogen contents. The occurrence of the donor-acceptor charge transfer was further evidenced by suppression of the n-doping of the PBT polymer by CNx. Nanoscale atomic force microscopy (AFM) and current-sensing AFM data suggested that CNx may form a bulk heterojunction with PBT.

Polycarbonate microchannel network with carpet of gold nanowires as SERS-active device.

A polycarbonate (PC) microchannel network supporting gold nanowires was developed to be a SERS-active microchip. Observations of large increases in a Raman cross-section, allowed us to collect vibrational signatures which are not easily detectable by Raman techniques due to the high fluorescence level of bare PC. Compared to other SERS experiments, this study relies on the use of dielectric polymer/metal surfaces which are well defined at microscale and nanoscale levels. This device seems a promising tool for sensing the adsorption of biomolecules.

Electroacoustic polymer microchip as an alternative to quartz crystal microbalance for biosensor development.

Laser photoablation of poly(ethylene terephthalate) (PET), a flexible dielectric organic polymer, was used to design an acoustic miniaturized DNA biosensor. The microchip device includes a 100-microm-thick PET layer, with two microband electrodes patterned in photoablated microchannels on one side and a depressed photoablated disk decorated by gold sputtered layer on the other side. Upon application of an electric signal between the two electrodes, an electroacoustic resonance phenomenon at approximately 30 MHz was established through the microelectrodes/PET/ gold layer interface. The electroacoustic resonance response was fitted with a series RLC motional arm in parallel with a static Co arm of a Buttlerworth-Van Dyke equivalent circuit: admittance spectra recorded after successive cycles of DNA hybridization on the gold surface showed reproducible changes on R, L, and C parameters. The same hybridizations runs were performed concomitantly on a 27-MHz (9 MHz, third overtone) quartz crystal microbalance in order to validate the PET device developed for bioanalysis applications. The electroacoustic PET device, approximately 100 times smaller than a microbalance quartz crystal, is interesting for the large-scale integration of acoustic sensors in biochips.

Characterization of counterion and surface influence on micelle formation using tapping mode atomic force microscopy in air.

Cylindrical micelles prepared in aqueous solutions from cationic surfactants octadecyl trimethylammonium (OTA+) or cetyltrimethylammonium (CTA+) and parachlorobenzoate (PCB) counterion were successfully imaged after evaporation of water using tapping mode atomic force microscopy (TM-AFM) onto very smooth gold and glass substrates. With the help of the obtained topography AFM images, it was shown that the micellar structures are preserved on gold substrates after evaporation of the solvent despite the new set of stresses due mainly to capillary forces and dehydration. The influence of the substrate on the resulting micellar morphology observed in air was investigated for these two materials: cylindrical micelles were evidenced as loosely adherent on gold surface in the presence of parachlorobenzoate (PCB) and identical, geometrically speaking, to those known to exist in aqueous solutions. In this situation, topographic AFM images allowed us to determine accurately their geometrical characteristics such as diameter and length in the nanometer range. On the other hand, AFM images obtained in air on glass surfaces revealed micellar structures that are different from those existing in the bulk of the solution. Indeed, bilayer-type micelles with a thickness close to twice the surfactant monomer expected length were observed, indicating that the well-established and strong influence of glass on micelle geometry at the glass/solution interface is maintained after evaporation of water. These results have been analyzed on the basis of positive charge of gold deduced from electrochemical impedance spectroscopy (EIS) and Raman spectroscopy measurements on one hand and of the negative charge of glass on the other hand. Although these results appeal to new theoretical considerations dealing with dynamics of evaporation of micellar solution drops and/or with counterion contributions to macromolecular interactions in aqueous solutions and in air, this new AFM imaging method appears to be the more adequate one to image and measure the micelles formed in the presence of water.