Microbial bio-production of a recombinant stimuli-responsive biosurfactant.

Biosurfactants have been the subject of recent interest as sustainable alternatives to petroleum-derived compounds in areas ranging from soil remediation to personal and health care. The production of naturally occurring biosurfactants depends on the presence of complex feed sources during microbial growth and requires multicomponent enzymes for synthesis within the cells. Conversely, designed peptide surfactants can be produced recombinantly in microbial systems, enabling the generation of improved variants by simple genetic manipulation. However, inefficient downstream processing is still an obstacle for the biological production of small peptides. We present the production of the peptide biosurfactant GAM1 in recombinant E. coli. Expression was performed in fusion to maltose binding protein using chemically defined minimal medium, followed by a single-step affinity capture and enzymatic cleavage using tobacco etch virus protease. Different approaches to the isolation of peptide after cleavage were investigated, with special emphasis on rapid and simple procedures. Solvent-, acid-, and heat-mediated precipitation of impurities were successfully applied as alternatives to post-cleavage chromatographic peptide purification, and gave peptide purities exceeding 90%. Acid precipitation was the method of choice, due to its simplicity and the high purification factor and recovery rate achieved here. The functionality of the bio-produced peptide was tested to ensure that the resulting peptide biosurfactant was both surface active and able to be triggered to switch between foam-stabilizing and foam-destabilizing states.

The interfacial structure and Young's modulus of peptide films having switchable mechanical properties.

We report the structure and Young's modulus of switchable films formed by peptide self-assembly at the air-water interface. Peptide surfactant AM1 forms an interfacial film that can be switched, reversibly, from a high- to low-elasticity state, with rapid loss of emulsion and foam stability. Using neutron reflectometry, we find that the AM1 film comprises a thin (approx. 15A) layer of ordered peptide in both states, confirming that it is possible to drastically alter the mechanical properties of an interfacial ensemble without significantly altering its concentration or macromolecular organization. We also report the first experimentally determined Young's modulus of a peptide film self-assembled at the air-water interface (E=80MPa for AM1, switching to E<20MPa). These findings suggest a fundamental link between E and the macroscopic stability of peptide-containing foam. Finally, we report studies of a designed peptide surfactant, Lac21E, which we find forms a stronger switchable film than AM1 (E=335MPa switching to E<4MPa). In contrast to AM1, Lac21E switching is caused by peptide dissociation from the interface (i.e. by self-disassembly). This research confirms that small changes in molecular design can lead to similar macroscopic behaviour via surprisingly different mechanisms.

Application of radiolabeled tracers to biocatalytic flux analysis.

Radiolabeled tracers can provide valuable information about the structure of and flux distributions in biocatalytic reaction networks. This method derives from prior studies of glucose metabolism in mammalian systems and is implemented by pulsing a culture with a radiolabeled metabolite that can be transported into the cells and subsequently measuring the radioactivity of all network metabolites following separation by liquid chromatography. Intracellular fluxes can be directly determined from the transient radioactivity count data by tracking the depletion of the radiolabeled metabolite and/or the accompanying accumulation of any products formed. This technique differs from previous methods in that it is applied within a systems approach to the problem of flux determination. It has been used for the investigation of the indene bioconversion network expressed in Rhodococcus sp. KY1. Flux estimates obtained by radioactive tracers were confirmed by macroscopic metabolite balancing and showed that indene oxidation in steady state chemostat cultures proceeds primarily through a monooxygenase activity forming (1S,2R)-indan oxide, with no dehydrogenation of trans-(1R,2R)-indandiol. These results confirmed the significance of indan oxide formation and identified the hydrolysis of indan oxide as a key step in maximizing the production of (2R)-indandiol, a chiral precursor of the HIV protease inhibitor, Crixivan.

Mössbauer and electron paramagnetic resonance studies of chloroperoxidase following mechanism-based inactivation with allylbenzene.

We have used Mössbauer and electron paramagnetic resonance (EPR) spectroscopy to study a heme-N-alkylated derivative of chloroperoxidase (CPO) prepared by mechanism-based inactivation with allylbenzene and hydrogen peroxide. The freshly prepared inactivated enzyme ("green CPO") displayed a nearly pure low-spin ferric EPR signal with g = 1.94, 2.15, 2.31. The Mössbauer spectrum of the same species recorded at 4.2 K showed magnetic hyperfine splittings, which could be simulated in terms of a spin Hamiltonian with a complete set of hyperfine parameters in the slow spin fluctuation limit. The EPR spectrum of green CPO was simulated using a three-term crystal field model including g-strain. The best-fit parameters implied a very strong octahedral field in which the three 2T2 levels of the (3d)5 configuration in green CPO were lowest in energy, followed by a quartet. In native CPO, the 6A1 states follow the 2T2 ground state doublet. The alkene-mediated inactivation of CPO is spontaneously reversible. Warming of a sample of green CPO to 22 degrees C for increasing times before freezing revealed slow conversion of the novel EPR species to two further spin S = 1/2 ferric species. One of these species displayed g = 1.82, 2.25, 2.60 indistinguishable from native CPO. By subtracting spectral components due to native and green CPO, a third species with g = 1.86, 2.24, 2.50 could be generated. The EPR spectrum of this "quasi-native CPO," which appears at intermediate times during the reactivation, was simulated using best-fit parameters similar to those used for native CPO.