Nanocomposite Catalyst for High-Performance and Durable Intermediate-Temperature Methane-Fueled Metal-Supported Solid Oxide Fuel Cells.

CH4-fueled metal-supported solid oxide fuel cells (CH4-MS-SOFCs) are propitious as CH4 is low-priced and readily available, and its renewable production is possible, such as biomethane. However, the current CH4-MS-SOFCs suffer from either poor power density or short durable operation, which is ascribed to the low catalytic activity and poor coking tolerance of the metallic anode support. Herein, we have deliberately designed and synthesized a highly active nanocomposite catalyst, Sm-doped CeO2-supported Ni, as the internal steam methane reforming catalyst, to optimize CH4-MS-SOFCs. Both power densities and durability of optimized CH4-MS-SOFCs have been dramatically enhanced compared to the pristine CH4-MS-SOFCs. The optimized CH4-MS-SOFCs deliver the highest performances among all zirconia-based CH4-MS-SOFCs. Furthermore, the operating temperature has been reduced to 600 °C. At 600 °C, a viable peak power density of >350 mW/cm2 is achieved, which is more than three times as high as the pristine CH4-MS-SOFCs. Furthermore, the optimized CH4-MS-SOFC achieves >1000 h of stable operation.

Enhanced CO2 Methanation Activity of Sm0.25Ce0.75O2-δ-Ni by Modulating the Chelating Agents-to-Metal Cation Ratio and Tuning Metal-Support Interactions.

Highly active and selective CO2 methanation catalysts are critical to CO2 upgrading, synthetic natural gas production, and CO2 emission reduction. Wet impregnation is widely used to synthesize oxide-supported metallic nanoparticles as the catalyst for CO2 methanation. However, as the reagents cannot be homogeneously mixed at an atomic level, it is challenging to modulate the microstructure, crystal structure, chemical composition, and electronic structure of catalysts via wet impregnation. Herein, a scalable and straightforward catalyst fabrication approach has been designed and validated to produce Sm0.25Ce0.75O2-δ-supported Ni (SDC-Ni) as the CO2 methanation catalyst. By varying the chelating agents-to-total metal cations ratio (C/I ratio) during the catalyst synthesis, we can readily and simultaneously modulate the microstructure, metallic surface area, crystal structure, chemical composition, and electronic structure of SDC-Ni, consequently fine-tuning the oxide-support interactions and CO2 methanation activity. The optimal C/I ratio (0.1) leads to an SDC-Ni catalyst that facilitates C-O bond cleavage and significantly improves CO2 conversion at 250 °C. A CO2-to-CH4 yield of >73% has been achieved at 250 °C. Furthermore, a stable operation of >1500 hours has been demonstrated, and no degradation is observed. Extensive characterizations were performed to fundamentally understand how to tune and enhance CO2 methanation activity of SDC-Ni by modulating the C/I ratio. The correlation of physical, chemical, and catalytic properties of SDC-Ni with the C/I ratio is established and thoroughly elaborated in this work. This study could be applied to tune the oxide-support interactions of various catalysts for enhancing the catalytic activity.

Synthesis of LaWN3 nitride perovskite with polar symmetry.

Oxide materials with the perovskite structure have been used in sensors and actuators for half a century, and halide perovskites transformed photovoltaics research in the past decade. Nitride perovskites have been computationally predicted to be stable, but few have been synthesized, and their properties remain largely unknown. We synthesized and characterized a nitride perovskite lanthanum tungsten nitride (LaWN3) in the form of oxygen-free sputtered thin films, according to spectroscopy, scattering, and microscopy techniques. We report a large piezoelectric response measured with scanning probe microscopy that together with synchrotron diffraction confirm polar symmetry of the perovskite LaWN3. Our LaWN3 synthesis should inspire growth of other predicted nitride perovskites, and measurements of their properties could lead to functional integration with nitride semiconductors for microelectromechanical devices.

Direct Measurement of Oxygen Mass Transport at the Nanoscale.

Tuning oxygen mass transport properties at the nanoscale offers a promising approach for developing high performing energy materials. A number of strategies for engineering interfaces with enhanced oxygen diffusivity and surface exchange have been proposed. However, the origin and the magnitude of such local effects remain largely undisclosed to date due to the lack of direct measurement tools with sufficient resolution. In this work, atom probe tomography with sub-nanometer resolution is used to study oxygen mass transport on oxygen-isotope exchanged thin films of lanthanum chromite. A direct 3D visualization of nanoscaled highly conducting oxygen incorporation pathways along grain boundaries, with reliable quantification of the oxygen kinetic parameters and correlative link to local chemistries, is presented. Combined with finite element simulations of the exact nanostructure, isotope exchange-atom probe tomography allowed quantifying an enhancement in the grain boundary oxygen diffusivity and in the surface exchange coefficient of lanthanum chromite of about 4 and 3 orders of magnitude, respectively, compared to the bulk. This remarkable increase of the oxygen kinetics in an interface-dominated material is unambiguously attributed to grain boundary conduction highways thanks to the use of a powerful technique that can be straightforwardly extended to the study of currently inaccessible multiple nanoscale mass transport phenomena.

An algorithm for correcting systematic energy deficits in the atom probe mass spectra of insulating samples.

Improvements in the mass resolution of a mass spectrometer directly correlate to improvements in peak identification and quantification. Here, we describe a post-processing technique developed to increase the quality of mass spectra of strongly insulating samples in laser-pulsed atom probe microscopy. The technique leverages the self-similarity of atom probe mass spectra collected at different times during an experimental run to correct for electrostatic artifacts that present as systematic energy deficits. We demonstrate the method on fused silica (SiO2) and neodymium-doped ceria (CeO2) samples which highlight the improvements that can be made to the mass spectrum of strongly insulating samples.

Field Ion Emission in an Atom Probe Microscope Triggered by Femtosecond-Pulsed Coherent Extreme Ultraviolet Light.

This paper describes initial experimental results from an extreme ultraviolet (EUV) radiation-pulsed atom probe microscope. Femtosecond-pulsed coherent EUV radiation of 29.6 nm wavelength (41.85 eV photon energy), obtained through high harmonic generation in an Ar-filled hollow capillary waveguide, successfully triggered controlled field ion emission from the apex of amorphous SiO2 specimens. The calculated composition is stoichiometric within the error of the measurement and effectively invariant of the specimen base temperature in the range of 25 K to 150 K. Photon energies available in the EUV band are significantly higher than those currently used in the state-of-the-art near-ultraviolet laser-pulsed atom probe, which enables the possibility of additional ionization and desorption pathways. Pulsed coherent EUV light is a new and potential alternative to near-ultraviolet radiation for atom probe tomography.

Orientation mapping with Kikuchi patterns generated from a focused STEM probe and indexing with commercially available EDAX software.

Relating a crystal's microscopic structure-such as orientation and size-to a material's macroscopic properties is of great importance in materials science. Although most crystal orientation microscopy is performed in the scanning electron microscope (SEM), transmission electron microscopy (TEM)-based methods have a number of benefits, including higher spatial resolution. Current TEM orientation methods have either specific hardware requirements or use software that has limited scope, utility, or availability. In this article, a technique is described for orientation mapping using Kikuchi diffraction patterns generated from a focused STEM probe. One key advantage is that indexing and analysis of the patterns and maps occurs in the robust OIM Analysis software, currently widely used for electron backscatter diffraction (EBSD) and transmission Kikuchi diffraction (TKD) analysis. It was found that with minimal to no image processing and by changing only a few software parameters, reliable indexing of Kikuchi patterns is possible. Three samples, a deformed ß-Titanium (Ti), a medium carbon heat-treated steel, and BaCe0.8Y0.2O3-δ were tested to determine the effectiveness of the approach. In all three measurements the algorithms effectively and reliably determined the phases and the crystal orientations of the features measured. For the two orientation maps produced, less than 5% of the patterns were misindexed including boundary areas where overlapping patterns existed. An angular resolution of 0.15° was achieved while features <25 nm were able to be spatially resolved.

A Three-Dimensional Atom Probe Microscope Incorporating a Wavelength-Tuneable Femtosecond-Pulsed Coherent Extreme Ultraviolet Light Source.

Pulsed coherent extreme ultraviolet (EUV) radiation is a potential alternative to pulsed near-ultraviolet (NUV) wavelengths for atom probe tomography. EUV radiation has the benefit of high absorption within the first few nm of the sample surface for elements across the entire periodic table. In addition, EUV radiation may also offer athermal field ion emission pathways through direct photoionization or core-hole Auger decay processes, which are not possible with the (much lower) photon energies used in conventional NUV laser-pulsed atom probe. We report preliminary results from what we believe to be the world's first EUV radiation-pulsed atom probe microscope. The instrument consists of a femtosecond-pulsed, coherent EUV radiation source interfaced to a local electrode atom probe tomograph by means of a vacuum manifold beamline. EUV photon-assisted field ion emission (of substrate atoms) has been demonstrated on various insulating, semiconducting, and metallic specimens. Select examples are shown.

Photo-Magnetic Irradiation-Mediated Multimodal Therapy of Neuroblastoma Cells Using a Cluster of Multifunctional Nanostructures.

The use of high intensity chemo-radiotherapies has demonstrated only modest improvement in the treatment of high-risk neuroblastomas. Moreover, undesirable drug specific and radiation therapy-incurred side effects enhance the risk of developing into a second cancer at a later stage. In this study, a safer and alternative multimodal therapeutic strategy involving simultaneous optical and oscillating (AC) magnetic field stimulation of a multifunctional nanocarrier system has successfully been implemented to guide neuroblastoma cell destruction. This novel technique permitted the use of low-intensity photo-magnetic irradiation and reduced the required nanoparticle dose level. The combination of released cisplatin from the nanodrug reservoirs and photo-magnetic coupled hyperthermia mediated cytotoxicity led to the complete ablation of the B35 neuroblastoma cells in culture. Our study suggests that smart nanostructure-based photo-magnetic hybrid irradiation is a viable approach to remotely guide neuroblastoma cell destruction, which may be adopted in clinical management post modification to treat aggressive cancers.

Self-consistent atom probe tomography reconstructions utilizing electron microscopy.

Atom probe tomography reconstructions provide valuable information on nanometer-scale compositional variations within materials. As such, the spatial accuracy of the reconstructions is of primary importance for the resulting conclusions to be valid. Here, the use of transmission electron microscopy images before and after atom probe analysis to provide additional information and constraints is examined for a number of different materials. In particular, the consistency between the input reconstruction parameters and the output reconstruction is explored. It is demonstrated that it is possible to generate reconstructions in which the input and known values are completely consistent with the output reconstructions. Yet, it is also found that for all of the datasets examined, a particular power law relationship exists such that, if the image compression factor or detection efficiency is not constrained, a series of similarly spatially accurate reconstructions results. However, if one of these values can be independently assessed, then the other is known as well. Means of incorporating these findings and this general methodology into reconstruction protocols are also discussed.

Electron diffraction and imaging for atom probe tomography.

Previous work has shown that pre- and post-experiment quantification of atom probe tomography (APT) specimen geometry using electron microscopy can constrain otherwise unknown parameters, leading to an improvement in data fidelity. To that end, an electron microscopy and diffraction system has been developed for in situ compatibility with modern APT hardware. The system is capable of secondary and backscattered scanning electron imaging, bright field and dark field scanning transmission electron imaging, and scanning transmission electron diffraction. Additionally, the system is also capable of in situ dynamic electron diffraction experiments using laser pulsed heating of the APT specimen.

p-type doping efficiency in CdTe: Influence of second phase formation.

Cadmium telluride (CdTe) high purity, bulk, crystal ingots doped with phosphorus were grown by the vertical Bridgman melt growth technique to understand and improve dopant solubility and activation. Large net carrier densities have been reproducibly obtained from as-grown ingots, indicating successful incorporation of dopants into the lattice. However, net carrier density values are orders of magnitude lower than the solubility of P in CdTe as reported in literature, 1018/cm3 to 1019/cm3 [J. H. Greenberg, J. Cryst. Growth 161, 1-11 (1996) and R. B. Hall and H. H. Woodbury, J. Appl. Phys. 39(12), 5361-5365 (1968)], despite comparable starting charge dopant densities. Growth conditions, such as melt stoichiometry and post growth cooling, are shown to have significant impacts on dopant solubility. This study demonstrates that a significant portion of the dopant becomes incorporated into second phase defects as compounds of cadmium and phosphorous, such as cadmium phosphide, which inhibits dopant incorporation into the lattice and limits maximum attainable net carrier density in bulk crystals. Here, we present an extensive study on the characteristics of these second phase defects in relation to their composition and formation kinetics while providing a pathway to minimize their formation and enhance solubility.

Impact of Wide-Ranging Nanoscale Chemistry on Band Structure at Cu(In, Ga)Se2 Grain Boundaries.

The relative chemistry from grain interiors to grain boundaries help explain why grain boundaries may be beneficial, detrimental or benign towards device performance. 3D Nanoscale chemical analysis extracted from atom probe tomography (APT) (10's of parts-per-million chemical sensitivity and sub-nanometer spatial resolution) of twenty grain boundaries in a high-efficiency Cu(In, Ga)Se2 solar cell shows the matrix and alkali concentrations are wide-ranging. The concentration profiles are then related to band structure which provide a unique insight into grain boundary electrical performance. Fluctuating Cu, In and Ga concentrations result in a wide distribution of potential barriers at the valence band maximum (VBM) (-10 to -160 meV) and the conduction band minimum (CBM) (-20 to -70 meV). Furthermore, Na and K segregation is not correlated to hampering donors, (In, Ga)Cu and VSe, contrary to what has been previously reported. In addition, Na and K are predicted to be n-type dopants at grain boundaries. An overall band structure at grain boundaries is presented.

Electron Beam-Induced Deposition for Atom Probe Tomography Specimen Capping Layers.

Six precursors were evaluated for use as in situ electron beam-induced deposition capping layers in the preparation of atom probe tomography specimens with a focus on near-surface features where some of the deposition is retained at the specimen apex. Specimens were prepared by deposition of each precursor onto silicon posts and shaped into sub-70-nm radii needles using a focused ion beam. The utility of the depositions was assessed using several criteria including composition and uniformity, evaporation behavior and evaporation fields, and depth of Ga+ ion penetration. Atom probe analyses through depositions of methyl cyclopentadienyl platinum trimethyl, palladium hexafluoroacetylacetonate, and dimethyl-gold-acetylacetonate [Me2Au(acac)] were all found to result in tip fracture at voltages exceeding 3 kV. Examination of the deposition using Me2Au(acac) plus flowing O2 was inconclusive due to evaporation of surface silicon from below the deposition under all analysis conditions. Dicobalt octacarbonyl [Co2(CO)8] and diiron nonacarbonyl [Fe2(CO)9] depositions were found to be effective as in situ capping materials for the silicon specimens. Their very different evaporation fields [36 V/nm for Co2(CO)8 and 21 V/nm for Fe2(CO)9] provide options for achieving reasonably close matching of the evaporation field between the capping material and many materials of interest.

Probing Grain-Boundary Chemistry and Electronic Structure in Proton-Conducting Oxides by Atom Probe Tomography.

A laser-assisted atom-probe-tomographic (LAAPT) method has been developed and applied to measure and characterize the three-dimensional atomic and electronic nanostructure at an yttrium-doped barium zirconate (BaZr0.9Y0.1O3-δ, BZY10) grain boundary. Proton-conducting perovskites, such as BZY10, are attracting intense interest for a variety of energy conversion applications. However, their implementation has been hindered, in part, because of high grain-boundary (GB) resistance that is attributed to a positive GB space-charge layer (SCL). In this study, LAAPT is used to analyze BZY10 GB chemistry in three dimensions with subnanometer resolution. From this analysis, maps of the charge density and electrostatic potential arising at the GBs are derived, revealing for the first time direct chemical evidence that a positive SCL indeed exists at these GBs. These maps reveal new insights on the inhomogeneity of the SCL region and produce an average GB potential barrier of approximately 580 mV, agreeing with previous indirect electrochemical measurements.

Effect of Diels-Alder Reaction in C60-Tetracene Photovoltaic Devices.

Developing organic photovoltaic materials systems requires a detailed understanding of the heterojunction interface, as it is the foundation for photovoltaic device performance. The bilayer fullerene/acene system is one of the most studied models for testing our understanding of this interface. We demonstrate that the fullerene and acene molecules chemically react at the heterojunction interface, creating a partial monolayer of a Diels-Alder cycloadduct species. Furthermore, we show that the reaction occurs during standard deposition conditions and that thermal annealing increases the concentration of the cycloadduct. The cycloaddition reaction reduces the number of sites available at the interface for charge transfer exciton recombination and decreases the charge transfer state reorganization energy, increasing the open circuit voltage. The submonolayer quantity of the cycloadduct renders it difficult to identify with conventional characterization techniques; we use atom probe tomography to overcome this limitation while also measuring the spatial distribution of each chemical species.

Synthesis of a mixed-valent tin nitride and considerations of its possible crystal structures.

Recent advances in theoretical structure prediction methods and high-throughput computational techniques are revolutionizing experimental discovery of the thermodynamically stable inorganic materials. Metastable materials represent a new frontier for these studies, since even simple binary non-ground state compounds of common elements may be awaiting discovery. However, there are significant research challenges related to non-equilibrium thin film synthesis and crystal structure predictions, such as small strained crystals in the experimental samples and energy minimization based theoretical algorithms. Here, we report on experimental synthesis and characterization, as well as theoretical first-principles calculations of a previously unreported mixed-valent binary tin nitride. Thin film experiments indicate that this novel material is N-deficient SnN with tin in the mixed ii/iv valence state and a small low-symmetry unit cell. Theoretical calculations suggest that the most likely crystal structure has the space group 2 (SG2) related to the distorted delafossite (SG166), which is nearly 0.1 eV/atom above the ground state SnN polymorph. This observation is rationalized by the structural similarity of the SnN distorted delafossite to the chemically related Sn3N4 spinel compound, which provides a fresh scientific insight into the reasons for growth of polymorphs of metastable materials. In addition to reporting on the discovery of the simple binary SnN compound, this paper illustrates a possible way of combining a wide range of advanced characterization techniques with the first-principle property calculation methods, to elucidate the most likely crystal structure of the previously unreported metastable materials.

Moderate level exposure to magnetic nanodots encased in tunable poly(ethylene glycol) analouge biopolymer shell do not deleteriously affect neurite outgrowth.

Recently, huge interest has been generated in investigating the possible therapeutic use of tunable magnetic nanostructures to overcome the existing challenges to treat central nervous system damage related conditions. However, several issues (e.g., biocompatibility or remote controlled actuation for multi-modal therapeutics) limit the use of conventional magnetic nanoparticles for biomedical applications. To address many of these shortcomings, we have synthesized a monodisperse nanoscale system consisting highly water dispersible magnetic nanodots encased in a remotely tunable polyethylene glycol analouge biopolymer shell. The monodisperse nature of the nanospheres, their response to external magnetic field and volumetric transition near physiological temperatures are very attractive, especially for drug delivery systems where triggered release is necessary. To further analyze the potential for combinatorial therapeutics for central nervous system damage related conditions, we have explored the efficiency of the uptake of nanospheres into pheochromocytoma cell line 12 (PC12) cells and assessed several additional measures of neurite outgrowth. We find that nanospheres were readily incorporated into the cytosolic compartment within 3 hours and did not alter the morphology of cellular processes compared to cells not exposed to nanospheres. Quantification of neurite outgrowth did not reveal any significant differences in neurite initiation or elongation between cells treated with moderate level nanomagnet exposure compared to control cultures under similar conditions. Thus, this study reports an attractive nano-scale system with great potential to deliver therapeutics to precise locations within the nervous system for axonal outgrowth and guidance.

Role of engineered nanocarriers for axon regeneration and guidance: current status and future trends.

There are approximately 1.5 million people who experience traumatic injuries to the brain and 265,000 who experience traumatic injuries to the spinal cord each year in the United States. Currently, there are few effective treatments for central nervous system (CNS) injuries because the CNS is refractory to axonal regeneration and relatively inaccessible to many pharmacological treatments. Smart, remotely tunable, multifunctional micro- and nanocarriers hold promise for delivering treatments to the CNS and targeting specific neurons to enhance axon regeneration and synaptogenesis. Furthermore, assessing the efficacy of treatments could be enhanced by biocompatible nanovectors designed for imaging in vivo. Recent developments in nanoengineering offer promising alternatives for designing biocompatible micro- and nanovectors, including magnetic nanostructures, carbon nanotubes, and quantum dot-based systems for controlled release of therapeutic and diagnostic agents to targeted CNS cells. This review highlights recent achievements in the development of smart nanostructures to overcome the existing challenges for treating CNS injuries.