Direct Ink Writing of Carbon-Doped Polymeric Composite Ink: A Review on Its Requirements and Applications.

Direct Ink Writing (DIW) opens new possibilities in three-dimensional (3D) printing of carbon-based polymeric ink. This is due to its ability in design flexibility, structural complexity, and environmental sustainability. This area requires exhaustive study because of its wide application in different manufacturing sectors. The present article is related to the variant emerging 3D printing techniques and DIW of carbonaceous materials. Carbon-based materials, extensively used for various applications in 3D printing, possess impressive chemical stability, strength, and flexible nanostructure. Fine printable inks consist predominantly of uniform solutions of carbon materials, such as graphene, graphene oxide (GO), carbon fibers (CFs), carbon nanotubes (CNTs), and solvents. It also contains compatible polymers and suitable additives. This review article elaborately discusses the fundamental requirements of DIW in structuring carbon-doped polymeric inks viz. ink formulation, required ink rheology, extrusion parameters, print fidelity prediction, layer bonding examination, substrate selection, and curing method to achieve fine functional composites. A detailed description of its application in the fields of electronics, medical, and mechanical segments have also been focused in this study.

Numerical and Experimental Mechanical Analysis of Additively Manufactured Ankle-Foot Orthoses.

Growing age and different conditions often require the replacement of orthoses, and FDM-based 3D printing can produce them quickly with less investment. In today's market for orthotics, these characteristics are highly desired. Therefore, this study is fully focused on the optimization and strength analysis of FDM 3D-printed ankle-foot orthoses (AFO) fabricated using PLA and PLA reinforced with carbon fiber (PLA-C). An increase in ankle plantar-flexor force can be achieved by reinforcing thermoplastic AFOs with CFs. Specially designed mechanical strength tests were conducted at the UTM to generate force-displacement curves for stored elastic energy and fracture studies. The mechanical behavior of both AFOs was predicted with the help of an FEA. The model predictions were validated by comparing them with mechanical strength testing conducted under the same loading and boundary conditions as the FEA. In both the prediction and experimental analysis, the PLA-C-based AFOs were stiffer and could withstand greater loads than the PLA-based AFOs. An area of high stress in the simulation and a fracture point in experimentation were both found at the same location. Furthermore, these highly accurate models will allow the fabrication of AFOs to be improved without investing time and resources on trials.

Surface Topography Analysis of Mg-Based Composites with Different Nanoparticle Contents Disintegrated Using Abrasive Water Jet.

This study investigated the effect of abrasive water jet kinematic parameters, such as jet traverse speed and water pressure, on the surface of magnesium-based metal matrix nanocomposites (Mg-MMNCs) reinforced with 50 nm (average particle size) Al2O3 particles at concentrations of 0.66 and 1.11 wt.%. The extent of grooving caused by abrasive particles and irregularities in the abrasive waterjet machined surface with respect to traverse speed (20, 40, 250 and 500 mm/min), abrasive flow rate (200 and 300 g/min) and water pressure (100 and 400 MPa) was investigated using surface topography measurements. The results helped to identify the mode of material disintegration during the process. The nanoindentation results show that material softening was decreased in nanocomposites with higher reinforcement content due to the presence of a sufficient amount of nanoparticles (1.11 wt.%), which protected the surface from damage. The values of selected surface roughness profile parameters-average roughness (Ra), maximum height of peak (Rp) and maximum depth of valleys (Rv)-reveal a comparatively smooth surface finish in composites reinforced with 1.11 wt.% at a traverse speed of 500 mm/min. Moreover, abrasive waterjet machining at high water pressure (400 MPa) produced better surface quality due to sufficient material removal and effective cleaning of debris from the machining zone as compared to a low water pressure (100 MPa), low traverse speed (5 mm/min) and low abrasive mass flow rate (200 g/min).

Role of graphene in biosensor and protective textile against viruses.

Coronavirus disease (COVID-19) is a recently discovered infectious disease caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). Graphene is an emerging material due to its extraordinary performance in the field of electronics and antimicrobial textiles. Special attention devoted to graphene oxide-based materials due to its surface to volume ratio is very high which make it easy to attach biomolecules by simple adsorption or by crosslinking between reactive groups and the graphene surface. In response to the COVID-19 pandemic, we have summarized the recent developments of graphene and its derivatives with possible virus detection and textile applications. Moreover, graphene strain sensors can be executed on high-performance textiles and high-throughput drug efficacy screening.