Constrained Transmit Beampattern Design Using a Correlated LFM-PC Waveform Set in MIMO Radar.

This paper considers the design of a desired transmit beampattern under the good ambiguity function constraint using a correlated linear frequency modulation-phase coded (LFM-PC) waveform set in multiple-input-multiple-output (MIMO) radar. Different from most existing beampattern design approaches, we propose using the LFM-PC waveform set to conquer the challenging problem of synthesizing waveforms with constant-envelope and easy-generation properties, and, meanwhile, solve the hard constraint of a good ambiguity behaviour. First, the ambiguity function of the LFM-PC waveform set is derived, and the superiority of LFM-PC waveforms over LFM and PC waveforms is verified. The temporal and spatial characteristic analysis of the LFM-PC waveform set demonstrates that both the transmit beampattern and sidelobe level are mainly affected by the frequency intervals, bandwidths, and phase-coded sequences of the LFM-PC waveform set. Finally, the constrained beampattern design problem is formulated by optimizing these parameters for desired beampatterns and low sidelobes at different doppler frequencies, which is a bi-objective optimization problem. To solve this, we propose a joint optimization strategy followed by a mandatory optimization, where the sequence quadratic programming (SQP) algorithm and adaptive clonal selection (ACS) algorithm are exploited iteratively. The simulation results demonstrate the efficiency of our proposed method.

An experimental study of deep brain stimulation lead fracture: possible fatigue mechanisms and prevention approach.

OBJECTIVES: Lead fracture is a common and troublesome hardware-related complication in deep brain stimulation therapy. Frequent cervical movements are suspected as the main cause, but the underlying mechanisms are still unclear. We propose the integrity of the helical structure of the lead wires is important and conduct systematic experiments to demonstrate this. We aim to provide a new view on how lead fracture takes place. MATERIALS AND METHODS: Flexural fatigue tests were conducted on intact and stretched lead wires with a custom-made testing machine. Number of cycles until failure was recorded as the fatigue life, and the fracture morphology was observed under optical and scanning electron microscopes. RESULTS: The fatigue life of the lead wires showed dramatic decline with the severity of deformation, from 434,112 ± 10,277 cycles for an intact specimen down to 19,435 ± 2,622 cycles for a specimen elongated by approximately 20%. The morphology of the fractures revealed characteristic beach marks and striations indicating a fatigue failure. CONCLUSION: We demonstrate that integrity of the helical structure of the wires is crucial to the fatigue performance of the lead. Although the results cannot be directly extrapolated to human subjects, they suggest a possible lead fracture mechanism. The implanted lead may undergo deformation due to large-amplitude motions (e.g., falls) and develop fracture due to the deterioration in fatigue resistance, especially when it is placed at or migrates to the neck. It may be possible to effectively protect the lead by using certain surgical techniques during implantation, such as placing the connector on the calvaria or in a drilled trough at the retroauricular region with reliable fixation.

Influences of spherical aberration on resonator's stable zones and fundamental mode output power scaling of solid state laser oscillators.

A parameter x is introduced to characterize the strength of thermal lens spherical aberration, whose influences on resonator's stable zones are analyzed theoretically. Some new and helpful results are obtained. For symmetrical plane-plane cavity, spherical aberration has just influence on the back edge of stable zone. For asymmetrical plane-plane cavity, spherical aberration has influence on the back edges of the two stable zones and the front edge of the second stable zone. Effects of transverse mode collapsing to TEM00 mode and stable zones separation of different order's transverse modes are pointed out, which is the foundation of TEM00 mode output power scaling for solid state laser oscillator. Influences of parameters such as resonator's long arm length, short arm length, and pump beam radius on the extent to which of stable zones separation of different order transverse modes are discussed. An experimental setup of a high power diodes dual-end pumped Nd:YVO4 TEM00 mode laser oscillator is built up and investigated experimentally. 51.2 W TEM00 mode output power in CW operation is achieved with an optical-to-optical efficiency of about 50% and beam quality factor M2 being 1.2.

Performance of large aperture tapered fiber phase conjugate mirror with high pulse energy and 1-kHz repetition rate.

A large aperture fused silica tapered fiber phase conjugate mirror is presented with a maximum 70% stimulated Brillouin scattering (SBS) reflectivity, which is obtained with 1 kHz repetition rate, 15 ns pulse width and 38 mJ input pulse energy. To the best of our knowledge, this is the highest SBS reflectivity ever reported by using optical fiber as a phase conjugate mirror for such high pulse repetition rate (1 kHz) and several tens of millijoule (mJ) input pulse energy. The influences of fiber end surface quality and pump pulse widths on SBS reflectivity are investigated experimentally. The results show that finer fiber end surface quality and longer input pulse widths are preferred for obtaining higher SBS reflectivity with higher input pulse energy. Double passing amplification experiments are also performed. 52 mJ pulse energy is achieved at 1 kHz repetition rate, with a reflected SBS pulse width of 1.5 ns and a M(2) factor of 2.3. The corresponding peak power reaches 34.6 MW. Obvious beam quality improvement is observed.

Beam quality improvement by gain guiding effect in end-pumped Nd:YVO4 laser amplifiers.

In end-pumped Nd:YVO4 amplifiers, beam quality improvement is obtained both in theory and in experiments. A theoretical model of gain-guided laser amplifier is developed by comprehensively considering thermal effect, gain guiding and gain saturation effect. Several key parameters of the amplifier are discussed such as the input beam quality, the beam filling factor between input beam and pump beam, the ratio between input power and pump power, and the length of laser crystal. The theoretical results are confirmed by the experiments.