Distance-dependent accuracy in Le Fort I maxillary repositioning procedures.

It has been hypothesised that, in maxillary repositioning procedures, longer distances correlate with less accurate transfers and particularly the repositioning forces of facial skin and muscles that increase exponentially. However, this has not to our knowledge been confirmed. The purpose of this study was to search for differences in the accuracy of transfer from maxillary repositioning procedures parallel to the three orthogonal planes and with respect to three different anatomical landmarks of the first molar left and right (M1L and M1R) and the first incisor (I). Cone-beam computed tomography (CT) datasets taken before and after operation for 92 patients who had Le Fort I maxillary repositioning procedures were aligned to measure the changes in the maxillary position in the axial, sagittal, and transverse directions. Differences between planned distances and those achieved were calculated and analysed with Pearsons correlation coefficient. The strongest significant correlations between the extent of planned repositioning distances and achieved differences (error) were detected in the sagittal plane for the anatomical landmarks of the right (M1R) and left first molar (M1L). Correlations became weaker if a limited planned distance ranging from 0-4mm was compared with a complete observed range that reached up to 12mm. Our results show for the first time to our knowledge that the accuracy of transfer of wafer-based maxillary positioning procedures depends on the distance being moved. Longer distances correlate with less accuracy, particularly in the sagittal plane and in the first molar region.

Three-dimensional fracture pattern analysis of the Obwegeser and Dal Pont bilateral sagittal split osteotomy.

The Obwegeser and Dal Pont modification of the bilateral sagittal split osteotomy (BSSO) is a well-established procedure in orthognathic surgery. The purpose of this retrospective study was to analyze the actual fracture patterns achieved with BSSO by Obwegeser and Dal Pont modification using postoperative cone beam computed tomography (CBCT) datasets from 100 patients. A total of 200 split osteotomies were assessed, which could be categorized into nine different split patterns. Only one of the observed split fractures (0.5%) followed exactly the fracture line described by Obwegeser and Dal Pont, whereas 40% followed the fracture line according to the Hunsuck and Epker modification and 13.5% were seen as unfavourable splits mainly running over the buccal plate. A significant correlation was found between unfavourable buccal splits and both horizontal osteotomies reaching the buccal surface at the dorsal ramus (P=0.001) and a vertical caudal bone cut end at the corpus with a buccal position (P<0.001). These results show that a complete antero-posterior horizontal osteotomy at the mandibular ramus does not lead to the intended fracture pattern, which rebuts the argument of a greater amount of bony overlap using the Obwegeser and Dal Pont modification.

Registration accuracy of three-dimensional surface and cone beam computed tomography data for virtual implant planning.

OBJECTIVE: Virtual wax-ups based on three-dimensional (3D) surface models can be matched (i.e. registered) to cone beam computed tomography (CBCT) data of the same patient for dental implant planning. Thereby, implant planning software can visualize anatomical and prosthetic information simultaneously. The aim of this study is to assess the accuracy of a newly developed registration process. MATERIAL AND METHODS: Data pairs of CBCT and 3D surface data of 16 patients for dental implant planning were registered and the discrepancy between the visualized 3D surface data and the corresponding CBCT data were measured on 64 teeth at seven points by two investigators in two iterations with a total of 1792 measurements. RESULTS: All data pairs were matched successfully and mean distances between CBCT and 3D surface data were between 0.03(±0.33) and 0.14(±0.18) mm. At two of seven measuring points, statistically significant correlations were determined between the measured error and the presence and type of restorations. Registration errors in maxilla and mandible were not statistically significantly different. CONCLUSION: According to the results of this study, registration of 3D surface data and CBCT data works reliably and is sufficiently accurate for dental implant planning. Thereby, barium-sulfate scanning templates can be avoided and dental implant planning can be accomplished fully virtual.

CAD/CAM-produced surgical guides: Optimizing the treatment workflow.

The increased availability of devices for 3D radiological diagnosis allows the more frequent use of CAD/CAM-produced surgical guides for implant placement. The conventional workflow requires a complex logistic chain which is time-consuming and costly. In a pilot study, the workflow of directly milled surgical guides was evaluated. These surgical guides were designed based on the fusion of an optical impression and the radiological data. The clinical use showed that the surgical guides could be accurately placed on the residual dentition without tipping movements. The conventional surgical guides were used as a control for the manual check of the deviation of the implant axis. The direct transfer of the digital planning data allows the fabrication of surgical guides in an external center without the need of physical transport, which reduces the logistic effort and expense of the central fabrication of surgical guides.