Harnessing Wharton's jelly stem cell differentiation into bone-like nodule on calcium phosphate substrate without osteoinductive factors.

An important aim of bone regenerative medicine is to design biomaterials with controlled chemical and topographical features to guide stem cell fate towards osteoblasts without addition of specific osteogenic factors. Herein, we find that sprayed bioactive and biocompatible calcium phosphate substrates (CaP) with controlled topography induce, in a well-orchestrated manner, Wharton's jelly stem cells (WJ-SCs) differentiation into osteoblastic lineage without any osteogenic supplements. The resulting WJ-SCs commitment exhibits features of native bone, through the formation of three-dimensional bone-like nodule with osteocyte-like cells embedded into a mineralized type I collagen. To our knowledge, these results present the first observation of a whole differentiation process from stem cell to osteocytes-like on a synthetic material. This suggests a great potential of sprayed CaP and WJ-SCs in bone tissue engineering. These unique features may facilitate the transition from bench to bedside and the development of successful engineered bone. STATEMENT OF SIGNIFICANCE: Designing materials to direct stem cell fate has a relevant impact on stem cell biology and provides insights facilitating their clinical application in regenerative medicine. Inspired by natural bone compositions, a friendly automated spray-assisted system was used to build calcium phosphate substrate (CaP). Sprayed biomimetic solutions using mild conditions led to the formation of CaP with controlled physical properties, good bioactivity and biocompatibility. Herein, we show that via optimization of physical properties, CaP substrate induce osteogenic differentiation of Wharton's jelly stem cells (WJ-SCs) without adding osteogenic supplement factors. These results suggest a great potential of sprayed CaP and WJ-SCs in bone tissue engineering and may facilitate the transition from bench to beside and the development of clinically successful engineered bone.

A new sol-gel synthesis of 45S5 bioactive glass using an organic acid as catalyst.

In this paper a new sol-gel approach was explored for the synthesis of the 45S5 bioactive glass. We demonstrate that citric acid can be used instead of the usual nitric acid to catalyze the sol-gel reactions. The substitution of nitric acid by citric acid allows to reduce strongly the concentration of the acid solution necessary to catalyze the hydrolysis of silicon and phosphorus alkoxides. Two sol-gel powders with chemical compositions very close to that of the 45S5 were obtained by using either a 2M nitric acid solution or either a 5mM citric acid solution. These powders were characterized and compared to the commercial Bioglass®. The surface properties of the two bioglass powders were assessed by scanning electron microscopy (SEM) and by Brunauer-Emmett-Teller method (BET). The Fourier transformed infrared spectroscopy (FTIR) and the X-ray diffraction (XRD) revealed a partial crystallization associated to the formation of crystalline phases on the two sol-gel powders. The in vitro bioactivity was then studied at the key times during the first hours of immersion into acellular Simulated Body Fluid (SBF). After 4h immersion into SBF we clearly demonstrate that the bioactivity level of the two sol-gel powders is similar and much higher than that of the commercial Bioglass®. This bioactivity improvement is associated to the increase of the porosity and the specific surface area of the powders synthesized by the sol-gel process. Moreover, the nitric acid is efficiently substituted by the citric acid to catalyze the sol-gel reactions without alteration of the bioactivity of the 45S5 bioactive glass.

Nanoscale surface modification of a prosthetic material: case of Ti6Al4V into Ringer's solution.

Nanoscale surface modification of Ti6Al4V prosthetic material was investigated at 37 degrees C into a physiological liquid named Ringer's solution. The root-mean-square surface roughness evolution of the material as a function of immersion time was evaluated by atomic force microscopy (AFM) and 3D reconstruction of scanning electron microscope images (SEM). The results obtained from both techniques clearly showed a decrease of the root-mean-square surface roughness during the first 6 hours of immersion in the physiological liquid that is followed by a stability of the roughness value at longer durations. Moreover, the study of the roughness parameters extracted from AFM measurements is used to explain the smoothing process occurring at the interface between the prosthetic material and the physiological liquid.

In vitro dissolution and corrosion study of calcium phosphate coatings elaborated by pulsed electrodeposition current on Ti6Al4V substrate.

Calcium-deficient hydroxyapatite (Ca-def-HAP) coatings on titanium alloy (Ti6Al4V) substrates are elaborated by pulsed electrodeposition. In vitro dissolution/precipitation process is investigated by immersion of the coated substrate into Dulbecco's Modified Eagle Medium (DMEM) from 1 h to 28 days. Calcium and phosphorus concentrations evolution in the biological liquid are determined by Induced Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES) for each immersion time. Physical and chemical characterizations of the coating are performed by scanning electron microscopy (SEM) associated to Energy Dispersive X-ray Spectroscopy (EDXS) for X-ray microanalysis. Surface modifications are investigated by an original method based on the three-dimensional reconstruction of SEM images (3D-SEM). Moreover, corrosion measurements are carried out by potentiodynamic polarization experiments. The results show that the precipitation rate of the Ca-def HAP coating is more pronounced in comparison with that of stoichiometric hydroxyapatite (HAP) used as reference. The precipitated bone-like apatite coating is thick, homogenous and exhibits an improved link to the substrate. Consequently, the corrosion behaviour of the elaborated prosthetic material is improved.