RESUMO
This paper conducted an experimental study of reduced models of a main gas pipeline for avalanche damage considering operational conditions. Two options were considered as a method of avalanche damage prevention: single steel rings at the crack edges and steel winding with a winding pitch of 0.25 m. For the tension force, 5% of the steel wire breaking force was taken, which was equal to 1 mm. The ambient environment was simulated by a climatic chamber, where two options of temperature loads were considered: +20 °C and -10 °C. It was found that reinforcement with single rings of pipeline models under conditions of positive (+20 °C) and negative (-10 °C) temperatures showed that the crack opening width in the ring direction decreased 1.63 times and 1.9 times, accordingly. The crack length (longitudinal direction) decreased 2.18 times and 2.45 times, accordingly. The reinforcement of the pipeline models with prestressed wire winding on the crack propagation under conditions of positive (+20 °C) and negative (-10 °C) temperatures showed that the width of the crack opening in the ring direction decreased 1.5 times and 1.46 times, accordingly. The crack length (longitudinal direction) decreased 1.4 times and 1.44 times accordingly, which is a positive moment in addressing the issue of the localisation and stoppage of a crack fracture in main gas pipelines. Simultaneously, the analysis of the prestressed pipelines model test results on crack fracture propagation showed that single rings are more effective, which decreased the crack opening width by 1.1 times and the crack length up to 1.5. Therefore, the experimental results obtained positively complement the available methods of crack localisation in main gas pipelines, which can be used by engineers and research communities when designing or reinforcing existing operating main steel gas pipelines.
RESUMO
In the study, experimental and theoretical studies were carried out to assess the influence of the shapes of dents in the tank wall on the stress-strain state of the defect zone. By testing fragments of a cylindrical tank, it was found that the most appropriate expression is (5), which could take into account the leaching of the tank wall, resulting in a decrease in the stress concentration index. At the same time, during theoretical studies in this paper, it was found that polynomials determined the stress concentration coefficient, where the obtained analytical expression data were compared with the data determined numerically in the ANSYS program, and it was found that the spread was from 2% to 10%. According to the results of a numerical study of the stress-strain state of the dent zone in the tank wall, graphical dependences of the stress concentration coefficient on the dimensionless depth of the dent for various values of the dimensionless radius of the dents and do not exceed 2% of the indicators that are obtained. At the conclusion of the experimental and numerical studies, a conclusion was made about the degree of influence of the geometric dimensions of the dents on the stress concentration index.
RESUMO
The paper presents the results of experimental studies of the features of the operation of prestressed shells, taking into account the various structural parameters of the prestress. It is established that when the winding angle changes from perpendicular to the shell axis to 75° and 65°, the circumferential stresses decrease 1.4 times and 1.2 times, respectively, and the axial stresses increase five and three times, which are two and four times lower than the circumferential, from which it can be concluded that the reduction in the winding angle to the longitudinal the axis of the shell has a positive effect on the stress state of the structure. The study also found that with an increase in the diameter of the winding wire from 1 to 2 mm and a change in the winding angle, the same nature of the stress distribution is observed, but the values of the stress state parameter change, so the efficiency increases up to 25% due to an increase in the winding thickness, depending on the pitch, angle and thickness of the winding, which favorably affects the strength and the bearing capacity of the structure as a whole by increasing the value of the stress state parameter. Thus, the results of the analysis will allow us to use in more detail the possibility of controlling the stress-strain state of the prestressed shell by changing the design parameters, and the results obtained can be used in design or construction, as well as when increasing the strength characteristics of the structure, which allows us to create a high-tech design optimal for these operating conditions, which can positively complement the studies conducted earlier in this direction.
