RESUMO
Almost 60% of oil and 40% of gas reserves worldwide are contained in carbonate reservoirs where acidizing stimulation is more challenging compared to sandstone reservoirs. Utilization of emulsified acids in matrix acidizing operations has been the most effective technique for more than half a century. This is due to the colloidal system's ability to generate deep, narrow conduits toward production zones under controlled retarded reactivity with the rock surface, along with the excellent sweep efficiency and corrosion inhibition of the well equipment. This Review attempts to review the various kinds of emulsified acids that are used for matrix acidizing of carbonate formations. The Review is trying to trace the innovations that have, gradually, been applied for enhancing the performance of emulsified acids for a variety of conditions, their limitations, and the developmental solutions such hybrid emulsifiers and pickering emulsions. In addition, the Review also discusses the parameters, characteristics, and measuring techniques required for the successful synthesis of a stable and quality emulsion while considering the environmental concerns raised toward the application of an emulsified acid system. From the reviewed publications, it can be summarized that macroemulsions are best suited for matrix acidizing applications over microemulsions due to low emulsifier concentrations and high acid volume retention; similarly, water in oil emulsions provide better retardation in a comparison to oil in water emulsions. The small droplet size of the emulsion yields high viscosity and stability. The compositional balance between each component present in the acidizing system is a crucial factor for optimum performance. Moreover, for future practice, much focus is required to design emulsified acids as ecofriendly systems that can leave the least amount of toxicity during and after implementation.
RESUMO
The use of nanomaterials as a means of recovering heavy and light oil from petroleum reservoirs has increased over the preceding twenty years. Most researchers have found that injecting a nanoparticle dispersion (nanofluids) has led to good results and increased the amount of oil that can be recovered. In this research, we aim to imitate the three-dimensional hexagonal prism in the existence of SiO2 and Al2O3 nanoparticles for better oil recovery. Porosity (0.1≤φ≤0.4), mass flow rate (0.05mL/min≤Q≤0.05ml/min), nanoparticle concentration (0.01≤ψ≤0.04), and the effect of relative permeability (kr) on oil and water saturation in the presence of gravity under different time durations are all investigated. The result obtained for the model is verified with existing experimental data. The results indicated that the infulence of nanoparticle volume fraction (VF) is significant in enhancing the oil recovery rate. It is also observed that at low porosity values the oil recovery is maximum. The maximum oil recovery is attained at low values of mass flow rate in the 3D hexagonal prism in the presence of silicon and aluminium nanoparticles It is also observed that the use of SiO2 gives a better oil recovery rate than Al2O3. It is also observed that maximum oil recovery is obtained at 99% at a flow rate of 0.05 mL/min in the presence of silicon injection.
RESUMO
Enhanced oil recovery (EOR) has been offered as an alternative to declining crude oil production. EOR using nanotechnology is one of the most innovative trends in the petroleum industry. In order to determine the maximum oil recovery, the effect of a 3D rectangular prism shape is numerically investigated in this study. Using ANSYS Fluent software(2022R1), we develop a two-phase mathematical model based on 3D geometry. This research examines the following parameters: flow rate Q = 0.01-0.05 mL/min, volume fractions = 0.01-0.04%, and the effect of nanomaterials on relative permeability. The result of the model is verified with published studies. In this study, the finite volume method is used to simulate the problem, and we run simulations at different flow rates while keeping other variables constant. The findings show that the nanomaterials have an important effect on water and oil permeability, increasing oil mobility and lowering IFT, which increases the recovery process. Additionally, it has been noted that a reduction in the flow rate improves oil recovery. Maximum oil recovery was attained at a 0.05 mL/min flow rate. Based on the findings, it is also demonstrated that SiO2 provides better oil recovery compared to Al2O3. When the volume fraction concentration increases, oil recovery ultimately increases.
RESUMO
Nanofluids and nanotechnology are very important in enhancing heat transfer due to the thermal conductivity of their nanoparticles, which play a vital role in heat transfer applications. Researchers have used cavities filled with nanofluids for two decades to increase the heat-transfer rate. This review also highlights a variety of theoretical and experimentally measured cavities by exploring the following parameters: the significance of cavities in nanofluids, the effects of nanoparticle concentration and nanoparticle material, the influence of the inclination angle of cavities, heater and cooler effects, and magnetic field effects in cavities. The different shapes of the cavities have several advantages in multiple applications, e.g., L-shaped cavities used in the cooling systems of nuclear and chemical reactors and electronic components. Open cavities such as ellipsoidal, triangular, trapezoidal, and hexagonal are applied in electronic equipment cooling, building heating and cooling, and automotive applications. Appropriate cavity design conserves energy and produces attractive heat-transfer rates. Circular microchannel heat exchangers perform best. Despite the high performance of circular cavities in micro heat exchangers, square cavities have more applications. The use of nanofluids has been found to improve thermal performance in all the cavities studied. According to the experimental data, nanofluid use has been proven to be a dependable solution for enhancing thermal efficiency. To improve performance, it is suggested that research focus on different shapes of nanoparticles less than 10 nm with the same design of the cavities in microchannel heat exchangers and solar collectors.
