Attaching artificial Achilles and tibialis cranialis tendons to bone using suture anchors in a rabbit model: assessment of outcomes.

Objective: The purpose of this study was to investigate the factors associated with outcomes of attaching artificial tendons to bone using suture anchors for replacement of biological tendons in rabbits. Study Design: Metal suture anchors with braided composite sutures of varying sizes (USP #1, #2, or #5) were used to secure artificial tendons replacing both the Achilles and tibialis cranialis tendons in 12 New Zealand White rabbits. Artificial tendons were implanted either at the time of (immediate replacement, n=8), or four weeks after (delayed replacement, n=4) resection of the biological tendon. Hindlimb radiographs of the rabbits were obtained immediately after surgery and approximately every other week until the study endpoint (16 weeks post-surgery). Results: All suture anchors used for the tibialis cranialis artificial tendons remained secure and did not fail during the study. The suture linkage between the Achilles artificial tendon and anchor failed in 9 of 12 rabbits. In all cases, the mode of failure was suture breakage distant from the knot. Based on radiographic analysis, the mean estimated failure timepoint was 5.3±2.3 weeks post-surgery, with a range of 2-10 weeks. Analysis of variance (ANOVA) tests revealed no significant effect of tendon implantation timing or suture size on either the timing or frequency of suture anchor failure. Conclusion: Based on the mode of failure, suture mechanical properties, and suture anchor design, we suspect that the cause of failure was wear of the suture against the edges of the eyelet in the suture anchor post, which reduced the suture strength below in vivo loads. Suture anchor designs differed for the tibialis cranialis and did not fail during the period of study. Future studies are needed to optimize suture anchor mechanical performance under different loading conditions and suture anchor design features.

Replacement of tibialis cranialis tendon with polyester, silicone-coated artificial tendon preserves biomechanical function in rabbits compared to tendon excision only.

BACKGROUND: Artificial tendons may be an effective alternative to autologous and allogenic tendon grafts for repairing critically sized tendon defects. The goal of this study was to quantify the in vivo hindlimb biomechanics (ground contact pressure and sagittal-plane motion) during hopping gait of rabbits having a critically sized tendon defect of the tibialis cranialis and either with or without repair using an artificial tendon. METHODS: In five rabbits, the tibialis cranialis tendon of the left hindlimb was surgically replaced with a polyester, silicone-coated artificial tendon (PET-SI); five operated control rabbits underwent complete surgical excision of the biological tibialis cranialis tendon in the left hindlimb with no replacement (TE). RESULTS: At 8 weeks post-surgery, peak vertical ground contact force in the left hindlimb was statistically significantly less compared to baseline for the TE group (p = 0.0215). Statistical parametric mapping (SPM) analysis showed that, compared to baseline, the knee was significantly more extended during stance at 2 weeks post-surgery and during the swing phase of stride at 2 and 8 weeks post-surgery for the TE group (p < 0.05). Also, the ankle was significantly more plantarflexed during swing at 2 and 8 weeks postoperative for the TE group (p < 0.05). In contrast, there were no significant differences in the SPM analysis among timepoints in the PET-SI group for the knee or ankle. CONCLUSIONS: Our findings suggest that the artificial tibialis cranialis tendon effectively replaced the biomechanical function of the native tendon. Future studies should investigate (1) effects of artificial tendons on other (e.g., neuromuscular) tissues and systems and (2) biomechanical outcomes when there is a delay between tendon injury and artificial tendon implantation.

A review of methods to measure tendon dimensions.

Tendons are soft tissues of the musculoskeletal system that are designed to facilitate joint movement. Tendons exhibit a wide range of mechanical properties matched to their functions and, as a result, have been of interest to researchers for many decades. Dimensions are an important aspect of tendon properties.Change in the dimensions of tissues is often seen as a sign of injury and degeneration, as it may suggest inflammation or general disorder of the tissue. Dimensions are also important for determining the mechanical properties and behaviours of materials, particularly the stress, strain, and elastic modulus. This makes the dimensions significant in the context of a mechanical study of degenerated tendons. Additionally, tendon dimensions are useful in planning harvesting for tendon transfer and joint reconstruction purposes.Historically, many methods have been used in an attempt to accurately measure the dimensions of soft tissue, since improper measurement can lead to large errors in the calculated properties. These methods can be categorised as destructive (by approximation), contact, and non-contact and can be considered in terms of in vivo and ex vivo.

Structured white light scanning of rabbit Achilles tendon.

BACKGROUND: The cross-sectional area (CSA) of a material is used to calculate stress under load. The mechanical behaviour of soft tissue is of clinical interest in the management of injury; however, measuring CSA of soft tissue is challenging as samples are geometrically irregular and may deform during measurement. This study presents a simple method, using structured light scanning (SLS), to acquire a 3D model of rabbit Achilles tendon in vitro for measuring CSA of a tendon. METHOD: The Artec Spider™ 3D scanner uses structured light and stereophotogrammetry technologies to acquire shape data and reconstruct a 3D model of an object. In this study, the 3D scanner was integrated with a custom mechanical rig, permitting 360-degree acquisition of the morphology of six New Zealand White rabbit Achilles tendons. The reconstructed 3D model was then used to measure CSA of the tendon. SLS, together with callipers and micro-CT, was used to measure CSA of objects with a regular or complex shape, such as a drill flute and human cervical vertebra, for validating the accuracy and repeatability of the technique. RESULTS: CSA of six tendons was measured with a coefficient of variation of less than 2%. The mean CSA was 9.9±1.0mm2, comparable with those reported by other researchers. Scanning of phantoms demonstrated similar results to µCT. CONCLUSION: The technique developed in this study offers a simple and accurate method for effectively measuring CSA of soft tissue such as tendons. This allows for localised calculation of stress along the length, assisting in the understanding of the function, injury mechanisms and rehabilitation of tissue.

Correlation of mechanical properties within the equine third metacarpal with trabecular bending and multi-density micro-computed tomography data.

Computed tomography (CT) data can be employed with respect to determining mechanical properties and has been used to predict parameters such as elastic modulus, yield strength, and ultimate strength of intact bone. Micro-computed tomography (muCT) possesses the resolution capable of detecting apparent bone density in extremely local regions and can characterize the trabecular structure. It has been asserted that this micro-structure is susceptible to micro-buckling and bending, which has a controversial role in predicting the global mechanical properties of bone. The current study measured the mechanical properties of relatively high apparent density bone from the equine distal third metacarpal. The mechanical properties were correlated with trabecular morphology parameters and apparent densities of localized regions obtained with muCT. These data were used to test two hypotheses: (1) accounting for trabecular bending using trabecular morphology parameters would provide better global mechanical property predictions than using only apparent density, and (2) regions of low apparent density dominate the overall mechanical behavior and provide greater correlation to the measured mechanical properties than regions of high apparent density. The data indicated that accounting for trabecular bending with morphological parameters resulted in stronger correlations to mechanical properties than correlations that relied only on apparent density (r2= 0.91 versus r2= 0.81). Low apparent density regions were more strongly correlated with mechanical properties than high apparent density regions (r2= 0.85 versus r2= 0.77), demonstrating the importance of selecting appropriate regions when attempting to predict mechanical properties from CT data.

Evaluation of increased subchondral bone density in areas of contact in the metacarpophalangeal joint during joint loading in horses.

OBJECTIVE: To quantitatively evaluate contact area under 2 loads and subjectively compare contact areas with subchondral bone (SCB) density patterns in intact metacarpophalangeal joints of horses. SAMPLE POPULATION: 6 forelimbs from horses without musculoskeletal disease. PROCEDURES: Computed tomographic scans of intact metacarpophalangeal joints were analyzed to obtain SCB density measurements. Each limb was loaded on a materials testing system to 150 degrees and 120 degrees extension in the metacarpophalangeal joint, and the joint was stained via intra-articular injection with safranin-O or toluidine blue, respectively. Each joint was disarticulated, and the surface area was digitized. Total articular surface area, contact area, and percentage contact area at each angle were calculated for the distal third metacarpal condyles, the proximal phalanx, and the proximal sesamoid bones. RESULTS: Contact area on the third metacarpal condyles, proximal sesamoid bones, and the proximal phalanx significantly increased with increased load. Areas of contact subjectively appeared to have a higher density on computed tomographic scans. CONCLUSIONS AND CLINICAL RELEVANCE: Areas consistently in contact under higher load were associated with increased SCB density. This supports the idea that the SCB adapts to the load applied to it. As load increased, contact area also increased, suggesting that areas not normally loaded may have a high degree of stress during impact loading. Quantifying how contact in the joint changes under different loading conditions and the adaptation of the bone to this change in normal and abnormal joints may provide insight into the pathogenesis of osteochondral disease.

PharmGKB: the Pharmacogenetics Knowledge Base.

The Pharmacogenetics Knowledge Base (PharmGKB; http://www.pharmgkb.org/) contains genomic, phenotype and clinical information collected from ongoing pharmacogenetic studies. Tools to browse, query, download, submit, edit and process the information are available to registered research network members. A subset of the tools is publicly available. PharmGKB currently contains over 150 genes under study, 14 Coriell populations and a large ontology of pharmacogenetics concepts. The pharmacogenetic concepts and the experimental data are interconnected by a set of relations to form a knowledge base of information for pharmacogenetic researchers. The information in PharmGKB, and its associated tools for processing that information, are tailored for leading-edge pharmacogenetics research. The PharmGKB project was initiated in April 2000 and the first version of the knowledge base went online in February 2001.