Molecular relays in nanometer-scale alumina: effective encapsulation for water-submersed halide perovskite photocathodes.

Halide perovskite (HaP) solar cells have an excellent voltage efficiency (>70%) and a low electron-affinity conduction band minimum, making them prospective candidates to be used as photocathodes in integrated low-cost solar fuel generators. However, halide perovskites are notoriously unstable in aqueous solutions and immediately dissolve upon exposure to water. Ultrathin layers (<10 nm) of Al2O3 deposited by atomic layer deposition are suitable encapsulants to prevent water ingression but are also electronically insulating. Embedding linear conjugated organic molecules ('molecular relays') that transverse the insulating layer enables selective electron transport across the insulating encapsulating layer. The electronic functionality of the embedded molecular relays is verified by conductive probe atomic force microscopy and photoelectrodeposition of metal particles (Pt and Ag) from ethanolic solutions. Lastly, the encapsulated HaP photoelectrodes were submersed in a CO2-saturated aqueous electrolyte and a photocurrent of ∼100 µA cm-2 (at ∼-0.32 V vs. Ag/AgCl) was measured, the highest reported for CsPbBr3 based aqueous photoelectrodes. This work demonstrates a way for stabilizing perovskite semiconductors in polar and protonic electrolytes as photoelectrodes for the generation of solar fuels.

Core-Shell Fe2O3@La1-xSrxFeO3-δ Material for Catalytic Oxidations: Coverage of Iron Oxide Core, Oxygen Storage Capacity and Reactivity of Surface Oxygens.

A series of Fe2O3@LSF (La0.8Sr0.2FeO3-δ perovskite) core-shell materials (CSM) was prepared by infiltration of LSF precursors gel containing various complexants and their mixtures to nanocrystalline aggregates of hematite followed by thermal treatment. The content of LSF phase and amount of carboxyl groups in complexant determine the percent coverage of iron oxide core with the LSF shell. The most conformal coating core-shell material was prepared with citric acid as the complexant, contained 60 wt% LSF with 98% core coverage. The morphology of the CSM was studied by HRTEM-EELS combined with SEM-FIB for particles cross-sections. The reactivity of surface oxygen species and their amounts were determined by H2-TPR, TGA-DTG, the oxidation state of surface oxygen ions by XPS. It was found that at complete core coverage with perovskite shell, the distribution of surface oxygen species according to redox reactivity in CSM resemble pure LSF, but its lattice oxygen storage capacity is 2-2.5 times higher. At partial coverage, the distribution of surface oxygen species according to redox reactivity resembles that in iron oxide.

Low-resistance monovalent-selective cation exchange membranes prepared using molecular layer deposition for energy-efficient ion separations.

The desalination of brackish water provides water to tens of millions of people around the world, but current technologies deplete much needed nutrients from the water, which is determinantal to both public health and agriculture. A selective method for brackish water desalination, which retains the needed nutrients, is electrodialysis (ED) using monovalent-selective cation exchange membranes (MVS-CEMs). However, due to the trade-off between membrane selectivity and resistance, most MVS-CEMs demonstrate either high transport resistance or low selectivity, which increase energy consumption and hinder the use of such membranes for brackish water desalination by ED. Here, we introduce a new method for fabrication of MVS-CEMs, using molecular layer deposition (MLD) to coat CEMs with ultrathin, hybrid organic-inorganic, positively charged layers of alucone. Using MLD enabled us to precisely control and minimize the selective layer thickness, while the flexibility and nanoporosity of the alucone prevent cracking and delamination. Under conditions simulating brackish water desalination, the modified CEMs provides monovalent selectivity with negligible added resistance-thereby alleviating the selectivity-resistance trade-off. Addressing the water-energy nexus, MLD-coating enables selective brackish water desalination with minimal increase in energy consumption and opens a new path for tailoring membranes' surface properties.

Tuning the Ion-Selectivity of Thin-Film Composite Nanofiltration Membranes by Molecular Layer Deposition of Alucone.

This work addresses a key challenge of tailoring the ion selectivity of a thin-film composite nanofiltration membrane to a specific application, such as water softening, without altering the water permeability. We modified the active surface of a commercial NF270 membrane by molecular layer deposition (MLD) of ethylene glycol-Al (EG-alucone). With increasing deposition cycles, we found that the MLD precursors first infiltrated and deposited in the active layer of NF270, then inflated the active layer, and finally deposited on the surface as a distinct EG-alucone layer. The deposition process changed the morphology of the membrane active layer and decreased the overall density of its fixed negative charge by embedding the positively charged EG-alucone. Filtration experiments revealed that these modifications affected the ion separation properties of the membrane without significantly hindering the water permeability. Specifically, the permeation of Na+ increased relative to that of Mg2+, as indicated by the permselectivity of Na+ salts over Mg2+ salts. The changes in permselectivities with an increasing number of MLD cycles were rationalized using the dielectric, steric, and electrostatic ion exclusion mechanisms, which are related to the membrane material, pore size, and fixed charge, respectively. These relations open a path for the rational design of nanofiltration membranes with tailored selectivity by tuning the properties of the MLD layer. Filtration results of natural brackish groundwater using the MLD modified membranes agreed with the single salt experiments. As a result, water hardness was 26% lower for the permeate obtained using the MLD-modified membranes, which were found stable even during a 24 h filtration run. These results highlight the practical potential of this approach in enhancing water softening efficiency.

Nanoscale membranes that chemically isolate and electronically wire up the abiotic/biotic interface.

By electrochemically coupling microbial and abiotic catalysts, bioelectrochemical systems such as microbial electrolysis cells and microbial electrosynthesis systems synthesize energy-rich chemicals from energy-poor precursors with unmatched efficiency. However, to circumvent chemical incompatibilities between the microbial cells and inorganic materials that result in toxicity, corrosion, fouling, and efficiency-degrading cross-reactions between oxidation and reduction environments, bioelectrochemical systems physically separate the microbial and inorganic catalysts by macroscopic distances, thus introducing ohmic losses, rendering these systems impractical at scale. Here we electrochemically couple an inorganic catalyst, a SnO2 anode, with a microbial catalyst, Shewanella oneidensis, via a 2-nm-thick silica membrane containing -CN and -NO2 functionalized p-oligo(phenylene vinylene) molecular wires. This membrane enables electron flow at 0.51 µA cm-2 from microbial catalysts to the inorganic anode, while blocking small molecule transport. Thus the modular architecture avoids chemical incompatibilities without ohmic losses and introduces an immense design space for scale up of bioelectrochemical systems.

Fabrication of Core-Shell Nanotube Array for Artificial Photosynthesis Featuring an Ultrathin Composite Separation Membrane.

Macroscale arrays of cobalt oxide-silica core-shell nanotubes with high aspect ratio and ultrathin walls of less than 20 nm have been fabricated. The silica shells feature embedded oligo-para(phenylenevinylene) molecules for charge transport across the insulating silica layer, which is tightly controlled by their electronic properties. The assembly is based on the use of a sacrificial Si nanorod array template combined with atomic layer deposition, covalent anchoring of organic wire molecules, and dry cryo-etching. High-resolution TEM imaging of samples prepared by microtome affords structural details of single core-shell nanotubes. The integrity of silica-embedded organic wire molecules exposed to atomic layer deposition, thermal treatment, and harsh etching procedures is demonstrated by grazing angle ATR FT-IR, FT-Raman, and XPS spectroscopy. The inorganic oxide-based core-shell nanotubes with ultrathin gas-impermeable, proton-conducting silica shells functionalized by molecular wires enable complete nanoscale photosynthetic units for CO2 reduction by H2O under membrane separation. Arrays of massive numbers of such core-shell nanotube units afford a design that extends the separation of the incompatible H2O oxidation and CO2 reduction catalysis environments across the continuum of length scales from nanometers to centimeters.

Ultrafast Charge Transfer between Light Absorber and Co3O4 Water Oxidation Catalyst across Molecular Wires Embedded in Silica Membrane.

The mechanism of visible light-induced hole transfer from a molecular light absorber, in the form of a free-base porphyrin, coupled to a Co3O4 nanoparticle catalyst for water oxidation by a molecular wire (p-oligo(phenylenevinylene) featuring three aryl units) is investigated by transient absorption spectroscopy. The wires are covalently anchored on the Co3O4 surface and embedded in a dense, yet ultrathin (2 nm), silica layer that separates light absorber and catalyst. The porphyrin is electrostatically adsorbed on the silica surface, and aqueous colloidal solutions of the core-shell particles are used for transient optical measurements. Pulsed optical excitation of the porphyrin results in rapid injection of the photogenerated hole onto the molecular wire and concurrent formation of reduced light absorber in less than 1 picosecond (ps). Ultrafast charge separation was monitored by transient absorption of the wire radical cation, which is given by bands in the 500 to 600 nm region and at 1130 nm, while formation of reduced porphyrin was characterized by absorption at 700 nm. Forward transfer of the hole to Co3O4 catalyst proceeds in 255 ± 23 ps. Ultrafast transfer of positive charge from the molecular assembly to a metal oxide nanoparticle catalyst for water oxidation is unprecedented. Holes on Co3O4 recombined with electrons of the reduced sensitizer with biphasic kinetics on a much longer time scale of ten to several hundred nanoseconds. The unusually efficient hole transfer coupling of a molecular light absorber with an Earth-abundant metal oxide catalyst by silica-embedded p-oligo(phenylenevinylene) offers an approach for integrated artificial photosystems featuring product separation on the nanoscale.

High-Work-Function Molybdenum Oxide Hole Extraction Contacts in Hybrid Organic-Inorganic Perovskite Solar Cells.

We investigate the effect of high work function contacts in halide perovskite absorber-based photovoltaic devices. Photoemission spectroscopy measurements reveal that band bending is induced in the absorber by the deposition of the high work function molybdenum trioxide (MoO3). We find that direct contact between MoO3 and the perovskite leads to a chemical reaction, which diminishes device functionality. Introducing an ultrathin spiro-MeOTAD buffer layer prevents the reaction, yet the altered evolution of the energy levels in the methylammonium lead iodide (MAPbI3) layer at the interface still negatively impacts device performance.

Hierarchical Inorganic Assemblies for Artificial Photosynthesis.

Artificial photosynthesis is an attractive approach for renewable fuel generation because it offers the prospect of a technology suitable for deployment on highly abundant, non-arable land. Recent leaps forward in the development of efficient and durable light absorbers and catalysts for oxygen evolution and the growing attention to catalysts for carbon dioxide activation brings into focus the tasks of hierarchically integrating the components into assemblies for closing of the photosynthetic cycle. A particular challenge is the efficient coupling of the multi-electron processes of CO2 reduction and H2O oxidation. Among the most important requirements for a complete integrated system are catalytic rates that match the solar flux, efficient charge transport between the various components, and scalability of the photosynthetic assembly on the unprecedented scale of terawatts in order to have impact on fuel consumption. To address these challenges, we have developed a heterogeneous inorganic materials approach with molecularly precise control of light absorption and charge transport pathways. Oxo-bridged heterobinuclear units with metal-to-metal charge-transfer transitions absorbing deep in the visible act as single photon, single charge transfer pumps for driving multi-electron catalysts. A photodeposition method has been introduced for the spatially directed assembly of nanoparticle catalysts for selective coupling to the donor or acceptor metal of the light absorber. For CO2 reduction, a Cu oxide cluster is coupled to the Zr center of a ZrOCo light absorber, while coupling of an Ir nanoparticle catalyst for water oxidation to the Co donor affords closing of the photosynthetic cycle of CO2 conversion by H2O to CO and O2. Optical, vibrational, and X-ray spectroscopy provide detailed structural knowledge of the polynuclear assemblies. Time resolved visible and rapid-scan FT-IR studies reveal charge transfer mechanisms and transient surface intermediates under photocatalytic conditions for guiding performance improvements. Separation of the water oxidation and carbon dioxide reduction half reactions by a membrane is essential for efficient photoreduction of CO2 by H2O to liquid fuel products. A concept of a macroscale artificial photosystem consisting of arrays of Co oxide-silica core-shell nanotubes is introduced in which each tube operates as a complete, independent photosynthetic unit with built-in membrane separation. The ultrathin amorphous silica shell with embedded molecular wires functions as a proton conducting, molecule impermeable membrane. Photoelectrochemical and transient optical measurements confirm tight control of charge transport through the membrane by the orbital energetics of the wire molecules. Hierarchical arrangement of the components is accomplished by a combination of photodeposition, controlled anchoring, and atomic layer deposition methods.

Coupling carbon dioxide reduction with water oxidation in nanoscale photocatalytic assemblies.

The reduction of carbon dioxide by water with sunlight in an artificial system offers an opportunity for utilizing non-arable land for generating renewable transportation fuels to replace fossil resources. Because of the very large scale required for the impact on fuel consumption, the scalability of artificial photosystems is of key importance. Closing the photosynthetic cycle of carbon dioxide reduction and water oxidation on the nanoscale addresses major barriers for scalability as well as high efficiency, such as resistance losses inherent to ion transport over macroscale distances, loss of charge and other efficiency degrading processes, or excessive need for the balance of system components, to mention a few. For the conversion of carbon dioxide to six-electron or even more highly reduced liquid fuel products, introduction of a proton conducting, gas impermeable separation membrane is critical. This article reviews recent progress in the development of light absorber-catalyst assemblies for the reduction and oxidation half reactions with focus on well defined polynuclear structures, and on novel approaches for optimizing electron transfer among the molecular or nanoparticulate components. Studies by time-resolved optical and infrared spectroscopy for the understanding of charge transfer processes between the chromophore and the catalyst, and of the mechanism of water oxidation at metal oxide nanocatalysts through direct observation of surface reaction intermediates are discussed. All-inorganic polynuclear units for reducing carbon dioxide by water at the nanoscale are introduced, and progress towards core-shell nanotube assemblies for completing the photosynthetic cycle under membrane separation is described.

Rain on Methylammonium Lead Iodide Based Perovskites: Possible Environmental Effects of Perovskite Solar Cells.

The great promise of hybrid organic-inorganic lead halide perovskite (HOIP)-based solar cells is being challenged by its Pb content and its sensitivity to water. Here, the impact of rain on methylammonium lead iodide perovskite films was investigated by exposing such films to water of varying pH values, simulating exposure of the films to rain. The amount of Pb loss was determined using both gravimetric and inductively coupled plasma mass spectrometry measurements. Using our results, the extent of Pb loss to the environment, in the case of catastrophic module failure, was evaluated. Although very dependent on module siting, even total destruction of a large solar electrical power generating plant, based on HOIPs, while obviously highly undesirable, is estimated to be far from catastrophic for the environment.

Crystallization of methyl ammonium lead halide perovskites: implications for photovoltaic applications.

Hybrid organic/lead halide perovskites are promising materials for solar cell fabrication, resulting in efficiencies up to 18%. The most commonly studied perovskites are CH3NH3PbI3 and CH3NH3PbI3-xClx where x is small. Importantly, in the latter system, the presence of chloride ion source in the starting solutions used for the perovskite deposition results in a strong increase in the overall charge diffusion length. In this work we investigate the crystallization parameters relevant to fabrication of perovskite materials based on CH3NH3PbI3 and CH3NH3PbBr3. We find that the addition of PbCl2 to the solutions used in the perovskite synthesis has a remarkable effect on the end product, because PbCl2 nanocrystals are present during the fabrication process, acting as heterogeneous nucleation sites for the formation of perovskite crystals in solution. We base this conclusion on SEM studies, synthesis of perovskite single crystals, and on cryo-TEM imaging of the frozen mother liquid. Our studies also included the effect of different substrates and substrate temperatures on the perovskite nucleation efficiency. In view of our findings, we optimized the procedures for solar cells based on lead bromide perovskite, resulting in 5.4% efficiency and Voc of 1.24 V, improving the performance in this class of devices. Insights gained from understanding the hybrid perovskite crystallization process can aid in rational design of the polycrystalline absorber films, leading to their enhanced performance.

Elucidating the charge carrier separation and working mechanism of CH3NH3PbI(3-x)Cl(x) perovskite solar cells.

Developments in organic-inorganic lead halide-based perovskite solar cells have been meteoric over the last 2 years, with small-area efficiencies surpassing 15%. We address the fundamental issue of how these cells work by applying a scanning electron microscopy-based technique to cell cross-sections. By mapping the variation in efficiency of charge separation and collection in the cross-sections, we show the presence of two prime high efficiency locations, one at/near the absorber/hole-blocking-layer, and the second at/near the absorber/electron-blocking-layer interfaces, with the former more pronounced. This 'twin-peaks' profile is characteristic of a p-i-n solar cell, with a layer of low-doped, high electronic quality semiconductor, between a p- and an n-layer. If the electron blocker is replaced by a gold contact, only a heterojunction at the absorber/hole-blocking interface remains.

Why lead methylammonium tri-iodide perovskite-based solar cells require a mesoporous electron transporting scaffold (but not necessarily a hole conductor).

CH3NH3PbI3-based solar cells were characterized with electron beam-induced current (EBIC) and compared to CH3NH3PbI(3-x)Clx ones. A spatial map of charge separation efficiency in working cells shows p-i-n structures for both thin film cells. Effective diffusion lengths, LD, (from EBIC profile) show that holes are extracted significantly more efficiently than electrons in CH3NH3PbI3, explaining why CH3NH3PbI3-based cells require mesoporous electron conductors, while CH3NH3PbI(3-Clx ones, where LD values are comparable for both charge types, do not.

Chloride Inclusion and Hole Transport Material Doping to Improve Methyl Ammonium Lead Bromide Perovskite-Based High Open-Circuit Voltage Solar Cells.

Low-cost solar cells with high VOC, relatively small (EG - qVOC), and high qVOC/EG ratio, where EG is the absorber band gap, are long sought after, especially for use in tandem cells or other systems with spectral splitting. We report a significant improvement in CH3NH3PbBr3-based cells, using CH3NH3PbBr3-xClx, with EG = 2.3 eV, as the absorber in a mesoporous p-i-n device configuration. By p-doping an organic hole transport material with a deep HOMO level and wide band gap to reduce recombination, the cell's VOC increased to 1.5 V, a 0.2 V increase from our earlier results with the pristine Br analogue with an identical band gap. At the same time, in the most efficient devices, the current density increased from ∼1 to ∼4 mA/cm(2).

Surface Photovoltage Spectroscopy Study of Organo-Lead Perovskite Solar Cells.

The field of organo-lead perovskite absorbers for solar cells is developing rapidly, with open-circuit voltage of reported devices already approaching the maximal theoretical voltage. Obtaining such high voltages on spun-cast or evaporated thin films is intriguing and calls for detailed investigation of the source of photovoltage in those devices. We present here a study of the roles of the selective contacts to methylammonium lead iodide chloride (MAPbI3-xClx) using surface photovoltage spectroscopy. By depositing and characterizing each layer at a time, we show that the electron-extracting interface is more than twice as effective as the hole-extracting interface in generating photovoltage, for several combinations of electrode materials. We further observe the existence of an electron-injection related spectral feature at 1.1 eV, which might bear significance for the cell's operation. Our results illustrate the usefulness of SPV spectroscopy in highlighting gaps in cells efficiency and for deepening the understanding of charge injection processes in perovskite-based photovoltaics.

Band alignment in partial and complete ZnO/ZnS/CdS/CuSCN extremely thin absorber cells: an X-ray photoelectron spectroscopy study.

In all solar cells, and especially in extremely thin absorber (ETA) solar cells, proper energy band alignment is crucial for efficient photovoltaic conversion. However, available tabulated data usually do not agree with actual results, and in most cases, Voc values lower than expected are achieved. In fact, ETA cells suffer from a very low Voc/Egap ratio, such as in ZnO/CdS/CuSCN cells. Here, we investigate limiting factors of ZnO/CdS/CuSCN ETA cells, applying X-ray photoelectron spectroscopy (XPS), chemically resolved electrical measurement (CREM), Kelvin probe, and I-V characterization. We show that electric fields are gradually developed in the cell upon increased absorber thickness. Moreover, an accumulation layer, unfavorable for the solar cell function, has been revealed at the oxide-absorber interface An effective chemical treatment to prevent formation of this accumulation layer is demonstrated.

High Open-Circuit Voltage Solar Cells Based on Organic-Inorganic Lead Bromide Perovskite.

Mesoscopic solar cells, based on solution-processed organic-inorganic perovskite absorbers, are a promising avenue for converting solar to electrical energy. We used solution-processed organic-inorganic lead halide perovskite absorbers, in conjunction with organic hole conductors, to form high voltage solar cells. There is a dire need for low-cost cells of this type, to drive electrochemical reactions or as the high photon energy cell in a system with spectral splitting. These perovskite materials, although spin-coated from solution, form highly crystalline materials. Their simple synthesis, along with high chemical versatility, allows tuning their electronic and optical properties. By judicious selection of the perovskite lead halide-based absorber, matching organic hole conductor, and contacts, a cell with a ∼ 1.3 V open circuit voltage was made. While further study is needed, this achievement provides a general guideline for additional improvement of cell performance.

Cryo-staining techniques in cryo-TEM studies of dispersed nanotubes.

The combination of cryo-TEM and staining is employed for studying protein-enabled dispersion of carbon nanotubes in aqueous solution. The same staining agent is used for both positive- and negative-staining. We are able to image the adsorbed layer of protein or polysaccharide on the nanotube but not the individual molecule. The process is not artifact-free due to change in ionic strength of the solution. However, our results are in line with other, not related, experimental techniques. The obtained information could be used to update models suggested based on, e.g., scattering data.