The effects of microstructure, Nb content and secondary Ruddlesden-Popper phase on thermoelectric properties in perovskite CaMn1-x Nb x O3 (x = 0-0.10) thin films.

CaMn1-x Nb x O3 (x = 0, 0.5, 0.6, 0.7 and 0.10) thin films have been grown by a two-step sputtering/annealing method. First, rock-salt-structured (Ca,Mn1-x ,Nb x )O thin films were deposited on 11̄00 sapphire using reactive RF magnetron co-sputtering from elemental targets of Ca, Mn and Nb. The CaMn1-x Nb x O3 films were then obtained by thermally induced phase transformation from rock-salt-structured (Ca,Mn1-x Nb x )O to orthorhombic during post-deposition annealing at 700 °C for 3 h in oxygen flow. The X-ray diffraction patterns of pure CaMnO3 showed mixed orientation, while Nb-containing films were epitaxially grown in [101] out of-plane-direction. Scanning transmission electron microscopy showed a Ruddlesden-Popper (R-P) secondary phase in the films, which results in reduction of the electrical and thermal conductivity of CaMn1-x Nb x O3. The electrical resistivity and Seebeck coefficient of the pure CaMnO3 film were measured to 2.7 Ω cm and -270 µV K-1 at room temperature, respectively. The electrical resistivity and Seebeck coefficient were reduced by alloying with Nb and was measured to 0.09 Ω cm and -145 µV K-1 for x = 0.05. Yielding a power factor of 21.5 µW K-2 m-1 near room temperature, nearly eight times higher than for pure CaMnO3 (2.8 µW K-2 m-1). The power factors for alloyed samples are low compared to other studies on phase-pure material. This is due to high electrical resistivity originating from the secondary R-P phase. The thermal conductivity of the CaMn1-x Nb x O3 films is low for all samples and is the lowest for x = 0.07 and 0.10, determined to 1.6 W m-1 K-1. The low thermal conductivity is attributed to grain boundary scattering and the secondary R-P phase.

Synthesis and characterization of single-phase epitaxial Cr2N thin films by reactive magnetron sputtering.

Cr2N is commonly found as a minority phase or inclusion in stainless steel, CrN-based hard coatings, etc. However, studies on phase-pure material for characterization of fundamental properties are limited. Here, Cr2N thin films were deposited by reactive magnetron sputtering onto (0001) sapphire substrates. X-ray diffraction and pole figure texture analysis show Cr2N (0001) epitaxial growth. Scanning electron microscopy imaging shows a smooth surface, while transmission electron microscopy and X-ray reflectivity show a uniform and dense film with a density of 6.6 g cm-3, which is comparable to theoretical bulk values. Annealing the films in air at 400 °C for 96 h shows little signs of oxidation. Nano-indentation shows an elastic-plastic behavior with H = 18.9 GPa and E r = 265 GPa. The moderate thermal conductivity is 12 W m-1 K-1, and the electrical resistivity is 70 µΩ cm. This combination of properties means that Cr2N may be of interest in applications such as protective coatings, diffusion barriers, capping layers and contact materials.

EuGMS Task and Finish group on Fall-Risk-Increasing Drugs (FRIDs): Position on Knowledge Dissemination, Management, and Future Research.

Falls are a major public health concern in the older population, and certain medication classes are a significant risk factor for falls. However, knowledge is lacking among both physicians and older people, including caregivers, concerning the role of medication as a risk factor. In the present statement, the European Geriatric Medicine Society (EuGMS) Task and Finish group on fall-risk-increasing drugs (FRIDs), in collaboration with the EuGMS Special Interest group on Pharmacology and the European Union of Medical Specialists (UEMS) Geriatric Medicine Section, outlines its position regarding knowledge dissemination on medication-related falls in older people across Europe. The EuGMS Task and Finish group is developing educational materials to facilitate knowledge dissemination for healthcare professionals and older people. In addition, steps in primary prevention through judicious prescribing, deprescribing of FRIDs (withdrawal and dose reduction), and gaps in current research are outlined in this position paper.

EuGMS Task and Finish group on Fall-Risk-Increasing Drugs (FRIDs): Position on Knowledge Dissemination, Management, and Future Research.

Falls are a major public health concern in the older population, and certain medication classes are a significant risk factor for falls. However, knowledge is lacking among both physicians and older people, including caregivers, concerning the role of medication as a risk factor. In the present statement, the European Geriatric Medicine Society (EuGMS) Task and Finish group on fall-risk-increasing drugs (FRIDs), in collaboration with the EuGMS Special Interest group on Pharmacology and the European Union of Medical Specialists (UEMS) Geriatric Medicine Section, outlines its position regarding knowledge dissemination on medication-related falls in older people across Europe. The EuGMS Task and Finish group is developing educational materials to facilitate knowledge dissemination for healthcare professionals and older people. In addition, steps in primary prevention through judicious prescribing, deprescribing of FRIDs (withdrawal and dose reduction), and gaps in current research are outlined in this position paper.

Ti n+1C n MXenes with fully saturated and thermally stable Cl terminations.

MXenes are a rapidly growing family of 2D materials that exhibit a highly versatile structure and composition, allowing for significant tuning of the materials properties. These properties are, however, ultimately limited by the surface terminations, which are typically a mixture of species, including F and O that are inherent to the MXene processing. Other and robust terminations are lacking. Here, we apply high-resolution scanning transmission electron microscopy (STEM), corresponding image simulations and first-principles calculations to investigate the surface terminations on MXenes synthesized from MAX phases through Lewis acidic melts. The results show that atomic Cl terminates the synthesized MXenes, with mere residual presence of other termination species. Furthermore, in situ STEM-electron energy loss spectroscopy (EELS) heating experiments show that the Cl terminations are stable up to 750 °C. Thus, we present an attractive new termination that widely expands the MXenes' functionalization space and enables new applications.

Theoretical study of phase stability, crystal and electronic structure of MeMgN2 (Me = Ti, Zr, Hf) compounds.

Scandium nitride has recently gained interest as a prospective compound for thermoelectric applications due to its high Seebeck coefficient. However, ScN also has a relatively high thermal conductivity, which limits its thermoelectric efficiency and figure of merit (zT). These properties motivate a search for other semiconductor materials that share the electronic structure features of ScN, but which have a lower thermal conductivity. Thus, the focus of our study is to predict the existence and stability of such materials among inherently layered equivalent ternaries that incorporate heavier atoms for enhanced phonon scattering and to calculate their thermoelectric properties. Using density functional theory calculations, the phase stability of TiMgN2, ZrMgN2 and HfMgN2 compounds has been calculated. From the computationally predicted phase diagrams for these materials, we conclude that all three compounds are stable in these stoichiometries. The stable compounds may have one of two competing crystal structures: a monoclinic structure (LiUN2 prototype) or a trigonal superstructure (NaCrS2 prototype; R 3 ¯ mH). The band structure for the two competing structures for each ternary is also calculated and predicts semiconducting behavior for all three compounds in the NaCrS2 crystal structure with an indirect band gap and semiconducting behavior for ZrMgN2 and HfMgN2 in the monoclinic crystal structure with a direct band gap. Seebeck coefficient and power factors are also predicted, showing that all three compounds in both the NaCrS2 and the LiUN2 structures have large Seebeck coefficients. The predicted stability of these compounds suggests that they can be synthesized by, e.g., physical vapor deposition.

Ti2Au2C and Ti3Au2C2 formed by solid state reaction of gold with Ti2AlC and Ti3AlC2.

Incorporation of layers of noble metals in non-van der Waals layered materials may be used to form novel layered compounds. Recently, we demonstrated a high-temperature-induced exchange process of Au with Si in the layered phase Ti3SiC2, resulting in the formation of Ti3AuC2 and Ti3Au2C2. Here, we generalize this technique showing that Au/Ti2AlC and Au/Ti3AlC2 undergo an exchange reaction at 650 °C to form Ti2Au2C and Ti3Au2C2 and determine their structures by electron microscopy, X-ray diffraction, and ab initio calculations. These results imply that noble-metal-containing layered phases should be possible to synthesize in many systems. The metal to be introduced should be inert to the transition-metal carbide layers, and exhibit negative heat of mixing with the initial A element in a liquid phase or two-phase liquid/solid region at the annealing temperature.

Building Bridges for Innovation in Ageing: Synergies between Action Groups of the EIP on AHA.

The Strategic Implementation Plan of the European Innovation Partnership on Active and Healthy Ageing (EIP on AHA) proposed six Action Groups. After almost three years of activity, many achievements have been obtained through commitments or collaborative work of the Action Groups. However, they have often worked in silos and, consequently, synergies between Action Groups have been proposed to strengthen the triple win of the EIP on AHA. The paper presents the methodology and current status of the Task Force on EIP on AHA synergies. Synergies are in line with the Action Groups' new Renovated Action Plan (2016-2018) to ensure that their future objectives are coherent and fully connected. The outcomes and impact of synergies are using the Monitoring and Assessment Framework for the EIP on AHA (MAFEIP). Eight proposals for synergies have been approved by the Task Force: Five cross-cutting synergies which can be used for all current and future synergies as they consider overarching domains (appropriate polypharmacy, citizen empowerment, teaching and coaching on AHA, deployment of synergies to EU regions, Responsible Research and Innovation), and three cross-cutting synergies focussing on current Action Group activities (falls, frailty, integrated care and chronic respiratory diseases).

Mo2Ga2C: a new ternary nanolaminated carbide.

We report the discovery of a new hexagonal Mo2Ga2C phase, wherein two Ga layers ­ instead of one ­ are stacked in a simple hexagonal arrangement in between Mo2C layers. It is reasonable to assume this compound is the first of a larger family.

Charge transfer and weak chemisorption of oxygen molecules in nanoporous carbon consisting of a disordered network of nanographene sheets.

The adsorption/desorption processes of oxygen are investigated in nanoporous carbon (activated carbon fiber (ACF)) consisting of a disordered network of nanographene sheets. The heat-induced desorption at 200 °C shows the decomposition of oxygen-including functional groups weakly bonded to nanographene edges. The removal of these oxygen-including negatively charged functional groups brings about a change in the type of majority carriers, from holes to electrons, through charge transfer from the functional groups to the interior of nanographene sheets. The oxygen adsorption brings ACF back to the electronic state with holes being majority carriers. In this process, a large concentration of negatively charged O(2)(δ-) molecules with δ ∼ 0.1 are created through charge transfer from nanographene sheets to the adsorbed oxygen molecules. The changes in the thermoelectric power and the electrical resistance in the oxygen desorption process is steeper than that in the oxygen adsorption process. This suggests the irreversibility between the two processes.

Electrical properties and far infrared optical conductivity of boron-doped single-walled carbon nanotube films.

Here we report a new approach for producing clean and homogeneous boron-doped single-walled carbon nanotubes. This approach combines the homogeneous dispersion of B(n)O(m)(+) ionic molecules over the nanotube surfaces in a liquid solution, with a high temperature chemical reaction that incorporates the boron atoms into the sp(2) carbon network of the nanotube wall. A comparative study of sheet resistance versus optical transmission in nanotube network films with and without boron-doping is also presented. Although electron energy loss spectroscopy revealed very low B-doping levels (<1 at.%), the dc conductivity of doped samples was raised by a factor of 3.4. Changes in the free carrier contribution to the optical conductivity of single-walled carbon nanotube (SWCNT) films induced by boron-doping was also studied via optical transmission in the far-infrared (IR) (50-7000 cm(-1)). A Drude model was fitted to the changes in the far-IR conductivity to quantify the additional free carrier concentration induced by the B-doping.

Measuring the fluorescent quantum efficiency of indocyanine green encapsulated in nanocomposite particulates.

We present results of a fluorescent quantum efficiency (Φ(F)) study on the encapsulation of the near-infrared dye indocyanine green (ICG) in bioresorbable calcium phosphate nanoparticles (CPNPs). The Φ(F) (described as the ratio of photons emitted to photons absorbed) provides a quantitative means of describing the fluorescence of an arbitrary molecule. However, standard quantum efficiency measurement techniques provide only the Φ(F) of the smallest fluorescing unit-in the case of a nanoparticle suspension, the nanoparticle itself. This presents a problem in accurately describing the Φ(F) of fluorophores embedded in an inorganic nanoparticle. Combining the incidence of scattering with an evaluation of the differences in local electric field and photochemical environment, we have developed a method to determine the Φ(F) of the constituent fluorescent molecules embedded in such a nanoparticle, which provides a more meaningful comparison with the unencapsulated fluorophore. While applicable to generic systems, we present results obtained by our method for the ICG-CPNP in a phosphate buffered 0.15 M saline solution (PBS, pH 7.4)--specifically, Φ(F, free dye) = 0.027 ± 0.001, Φ(F, particle) = 0.053 ± 0.003, and for the individual encapsulated molecules, Φ(F, molecule) = 0.066 ± 0.004. The method developed also provides insight into the influences of encapsulation and key parameters to engineer resonant enhancement effects from the emission of the encapsulated fluorophores corresponding to an eigenmode of the embedding particle for tailored optical properties.

Inhibition of Akt signaling by the lignan matairesinol sensitizes prostate cancer cells to TRAIL-induced apoptosis.

Tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) has been shown to be selectively pro-apoptotic in cancer cells, with minimal toxicity to normal tissues. Although this feature makes TRAIL a promising anticancer agent, not all cancer cell types are sensitive to TRAIL-induced apoptosis despite abundant expression of TRAIL receptors. Thus, combinatorial treatments to sensitize tumor cells to TRAIL-induced apoptosis have been in the focus of extensive research. Dietary lignans have shown cancer preventive and antitumorigenic activity, but the mechanisms behind these effects are poorly known. Here we observed that of the three tested lignan molecules, matairesinol (MAT) was the most effective as a death receptor-sensitizing agent. MAT sensitized the androgen-dependent LNCaP cells to TRAIL-induced apoptosis both in the presence and absence of androgens. Treatment with MAT markedly decreased Akt activity, which has been implicated as a key signaling mechanism in the TRAIL resistance of LNCaP prostate cancer cells. The involvement of the pathway in the MAT-mediated sensitization was shown in rescue experiments using ectopic expression of constitutively active Akt. Owing to the high activity of phosphatidylinositol 3-kinase/Akt signaling in cancer, targeting this survival pathway with MAT could markedly benefit TRAIL-based tumor therapies, including those aimed at prostate cancer.

Transparent boron-doped carbon nanotube films.

We report results of studies on the sheet resistance and optical transmission of thin films of boron-doped single-walled carbon nanotubes (SWNTs). Boron doping was carried out by exposure of SWNTs to B 2O 3 and NH 3 at 900 degrees C and 1-3 atom % boron was found in the SWNT bundles via electron energy loss spectroscopy (EELS). Boron doping was found to downshift the positions of the optical absorption bands associated with the van Hove singularities (E 11 (s) E 22 (s) and E 11 (m)) by approximately 30 meV relative to their positions in acid-treated and annealed SWNTs. Raman spectroscopy, EELS, and optical data are consistent with the picture that a few atom % boron has been substituted for carbon in the sp (2) framework of SWNTs. Finally, our results show that boron doping does not significantly affect the optical transmittance in the visible region. However, boron doping lowers the sheet resistance by approximately 30% relative to pristine SWNT films from the same batch. Boron-doped SWNT may provide a better approach to touch-screen technology.

Electronic properties of semiconductor nanowires.

This paper provides a review of the state-of-the-art electronic-structure calculations of semiconductor nanowires. Results obtained using empirical k.p, empirical tight-binding, semi-empirical pseudopotential, and with ab initio methods are compared. For conciseness, we will restrict our detailed discussions to free-standing plain and modulated nanowires. Connections to relevant experimental data, particularly band gaps and polarization anisotropy, will be made since these results depend crucially on the electronic properties. For completeness, a brief review on the synthesis of nanowires is included.

Synthesis and raman scattering from Zn(1-x)Mn(x)S diluted magnetic semiconductor nanowires.

The growth of Diluted Magnetic Semiconducting (DMS) Zn(1-x)Mn(x)S (0 < or = x < 0.6) nanowires (NWs) using a three-zone furnace and two solid sources is reported. The approach is generally applicable to many binary and ternary NW systems that grow by the Vapor-Liquid-Solid growth mechanism. Mn concentration was controlled by the temperature of the Mn source. The Zn/Mn ratio was found to determine the crystalline structure, i.e., wurtzite or zinc blende. High-resolution transmission electron microscopy measurements revealed highly crystalline single phase NWs. The vibrational properties of the DMS NWs with different Zn/Mn ratios were studied by correlating their Raman scattering spectra with the composition measured by Energy Dispersive X-Ray Spectroscopy (EDS). We find that the transverse optical (TO) phonon band disappears at the lowest Mn concentrations, while the longitudinal optical (LO) phonon band position was found insensitive to x. Three additional Raman bands were observed between the ZnS q = 0 TO and LO phonons when Mn atoms were present in the NWs. These bands are similar to those reported previously for bulk Zn(1-x)Mn(x)S and their origin is still controversial.

Optical antenna effect in semiconducting nanowires.

We report on investigations of the interaction of light with nanoscale antennae made from crystalline GaP nanowires (NWs). Using Raman scattering, we have observed strong optical antenna effects which we identify with internal standing wave photon modes of the wire. The antenna effects were probed in individual NWs whose diameters are in the range 40 < d < 300 nm. The data and our calculations show that the nature of the backscattered light is critically dependent on the interplay between a photon confinement effect and bulk Raman scattering. At small diameter, d < 65 nm, the NWs are found to act like a nearly perfect dipole antenna and the bulk Raman selection rules are masked leading to a polarized scattering intensity function I R approximately cos4 theta. Underscoring the importance of this work is the realization that a fundamental understanding of the "optical antenna effect" in semiconducting NWs is essential to the analysis of all electro-optic effects in small diameter filaments.

Raman scattering from high-frequency phonons in supported n-graphene layer films.

Results of room-temperature Raman scattering studies of ultrathin graphitic films supported on Si (100)/SiO2 substrates are reported. The results are significantly different from those known for graphite. Spectra were collected using 514.5 nm radiation on films containing from n = 1 to 20 graphene layers, as determined by atomic force microscopy. Both the first- and second-order Raman spectra show unique signatures of the number of layers in the film. The nGL film analogue of the Raman G-band in graphite exhibits a Lorentzian line shape whose center frequency shifts linearly relative to graphite as approximately 1/n (for n = 1 omegaG approximately 1587 cm-1). Three weak bands, identified with disorder-induced first-order scattering, are observed at approximately 1350, 1450, and 1500 cm-1. The approximately 1500 cm-1 band is weak but relatively sharp and exhibits an interesting n-dependence. In general, the intensity of these D-bands decreases dramatically with increasing n. Three second-order bands are also observed (approximately 2450, approximately 2700, and 3248 cm-1). They are analogues to those observed in graphite. However, the approximately 2700 cm-1 band exhibits an interesting and dramatic change of shape with n. Interestingly, for n < 5 this second-order band is more intense than the G-band.

Coherent twinning phenomena: towards twinning superlattices in III-V semiconducting nanowires.

We report evidence in GaP and InP nanowires for a coherent modulation of the structure along the wire axis. By using electron diffraction, we have observed an additional series of diffraction peaks consistent with a quasiperiodic placement of twinning boundaries along the wire. This observation is indeed unexpected, as the vapor-liquid-solid growth conditions used to produce the nanowires were not modulated. The averaged repeat distance of the structure, i.e., the distance between twin boundaries, has been found to depend on the temperature gradient imposed in the growth zone. Future control of the twinning superlattice period should allow significant design possibilities for electronic, thermoelectric, thermal and electro-optic applications of semiconducting nanowires.

Force-deflection spectroscopy: a new method to determine the Young's modulus of nanofilaments.

We demonstrate the determination of Young's modulus of nanowires or nanotubes via a new approach, that is, force-deflection spectroscopy (FDS). An atomic force microscope is used to measure force versus deflection (F-D) curves of nanofilaments that bridge a trench patterned in a Si substrate. The FD data are then fit to the Euler-Bernoulli equation to determine Young's modulus. Our approach provides a generic platform from which to study the mechanical and piezoelectric properties of a variety of materials at the nanoscale level. Young's modulus measurements on ZnS (wurtzite) nanowires are presented to demonstrate this technique. We find that the Young's modulus for rectangular cross section ZnS nanobelts is 52 +/- 7.0 GPa, about 30% smaller than that reported for the bulk.