Parametric study for optimizing double-layer microchannel heat sink for solar panel thermal management.

The most significant issue affecting the electric efficiency of solar panels is overheating. Concentration photovoltaic (CPV) modules work by converting approximately 80% of sunlight to heat; this may exceed the cell operating temperature limits. Therefore, thermal management is the best choice for keeping such panels working under specified conditions. Prior to producing an actual solar indoor unit, the current research primarily focuses on optimizing the heat sink dimensions that affect the cooling performance of the solar panel. Two parametric studies were employed to optimize the microchannel heat sink design. First, a two-dimensional numerical study was implemented to optimize the best channel height for more uniform flow inside a double-layer microchannel heat sink (DL-MCHS); the width of channels was kept as a constant value. Second, a three-dimensional conjugate heat transfer model for fluid flow in the optimized heat sink was used to optimize the inlet/outlet header length. To evaluate the overall CPV performance, a further numerical case study was carried out for the optimized designs at a wide range of inlet mass flow rates and steady-state heat flux. The findings indicated that a channel height of 0.5 mm and a header length of 20 mm were the best design points for the suggested heat sink. To assess the effectiveness of a solar/thermal module, the selected design points were applied to a 3D model. The maximum electricity efficiency measured was 17.45%, nearly 40% greater than the typical CPV/T system.

Invention of Hollow Zirconium Tungesto-Vanadate at Nanotube Morphological Structure for Radionuclides and Heavy Metal Pollutants Decontamination from Aqueous Solutions.

Zirconium tungesto-vanadate cation exchange material was successfully architectured at open ended nanotubes morphological structure in the presence of polyvinyl alcohol as a stabilizing agent using microwave route. The ion exchange capacity (IEC) of the material was recorded as 4.8 meq/g of about 640 m(2)/g for a specific surface area. The x-ray diffraction pattern of the material implies its crystallinity. Both scanning and transmission electron microscopes identified the average aspect ratio of the architectured nanotubes as 6.5 and its hollow structure. The material posed 96.4 % cadmium ion decontamination within 90 min compared with 84 % strontium decontamination at the same time.

Construction of Zinc Oxide into Different Morphological Structures to Be Utilized as Antimicrobial Agent against Multidrug Resistant Bacteria.

Nano-ZnO has been successfully implemented in particles, rods, and tubes nanostructures via sol-gel and hydrothermal techniques. The variation of the different preparation parameters such as reaction temperature, time, and stabilizer agents was optimized to attain different morphological structures. The influence of the microwave annealing process on ZnO crystallinity, surface area, and morphological structure was monitored using XRD, BET, and SEM techniques, respectively. The antimicrobial activity of zinc oxide produced in nanotubes structure was examined against four different multidrug resistant bacteria: Gram-positive (Staphylococcus aureus and Bacillus subtilis) and Gram-negative (Escherichia coli and Pseudomonas aeruginosa) strains. The activity of produced nano-ZnO was determined by disc diffusion technique and the results revealed that ZnO nanotubes recorded high activity against the studied strains due to their high surface area equivalent to 17.8 m(2)/g. The minimum inhibitory concentration (MIC) of ZnO nanotubes showed that the low concentrations of ZnO nanotubes could be a substitution for the commercial antibiotics when approached in suitable formula. Although the annealing process of ZnO improves the degree of material crystallinity, however, it declines its surface area and consequently its antimicrobial activity.

Bacillus mojavensis strain 32A, a bioflocculant-producing bacterium isolated from an Egyptian salt production pond.

Bacillus mojavensis strain 32A that exhibited 96.11% flocculation efficiency for clay suspensions was selected from other 15 comparative strains. Under growth condition, strain 32A was able to produce 5.2g/L of purified biopolymer. Its constituent was mainly polysaccharide and protein with proportional of 98.4-1.6% respectively. FTIR spectrum was confirming its chemical analysis. This biopolymer attain very fast sedimentation rate. The cost-effective biopolymer and CaCl(2) dosages were 3mg/L and 5 ml/L respectively that posed 89.7% flocculation efficiency. These dosages were suitable only for clay concentrations ≤5g/L. The maximum flocculation efficiency of the biopolymer recorded at pH 1.0 of clay suspension. The too high (>75°C) or too low (<25°C) clay suspension temperature was unfavorable for the biopolymer flocculation performance. The biopolymer solution utilized high thermal stability over the temperature range of 5-60°C. Furthermore, its pH stability recorded at pH range of 5-9.