The effect of the hydrophilic spacer length on the functionality of a mercury-supported tethered bilayer lipid membrane.

A biomimetic membrane consisting of a thiolipid monolayer tethered to a mercury electrode, with a dioleoylphosphatidylcholine (DOPC) monolayer on top of it, was fabricated. The thiolipid, referred to as DPOL, consisted of an octaethyleneoxy (OEO) chain terminated at one end with a lipoic acid residue and covalently linked at the other end to two phytanyl chains. The functionality of this biomimetic membrane, referred to as a tethered bilayer lipid membrane (tBLM), was tested by incorporating gramicidin and alamethicin and verifying their ion channel activity. Advantages and drawbacks with respect to a tBLM using a thiolipid, referred to as DPTL, with a tetraethyleneoxy (TEO) chain were examined by using electrochemical impedance spectroscopy, potential-step chronocoulometry and cyclic voltammetry. The maximum charge surface density of potassium ions stored in the OEO spacer amounts to 70µCcm(-2), as compared to a charge surface density of 45µCcm(-2) in the TEO spacer. The lipid bilayer moiety of the DPOL/DOPC tBLM is somewhat leakier than that of the DPTL/DOPC tBLM at potentials negative of about -0.65V vs. the saturated calomel electrode. The estimated value of the surface dipole potential of the OEO spacer amounts to -0.180V and is, therefore, smaller than that, -0.230V, of the TEO spacer.

In situ PM-IRRAS studies of an archaea analogue thiolipid assembled on a au(111) electrode surface.

Polarization modulation infrared reflection absorption spectroscopy (PM-IRRAS) has been applied to determine the conformation, orientation, and hydration of a monolayer of 2,3-di-O-phytanyl-sn-glycerol-1-tetraethylene glycol-dl-alpha-lipoic acid ester (DPTL) self-assembled at a gold electrode surface. This Archaea analogue thiolipid has been recently employed to build tethered lipid bilayers. By synthesizing DPT(d16)L, a DPTL molecule with a deuterium substituted tetraethylene glycol spacer, it was possible to differentiate the C-H stretch vibrations of the phytanyl chains from the tetraethylene glycol spacer and acquire the characteristic IR spectra for the chains, spacer, and lipoic acid headgroup separately. Our results show that the structure of the monolayer displays remarkable stability in a broad range of electrode potentials and that the phytanyl chains remain in a liquid crystalline state. The tetraethylene glycol chains are coiled, and the IR spectrum for this region shows that it is in the disordered state. The most significant result of this study is the information that in contrast to expectations the spacer region is poorly hydrated. Our results have implications for the design of a tethered lipid membrane based on this thiolipid.

New deuterated oligo(ethylene glycol) building blocks and their use in the preparation of surface active lipids possessing labeled hydrophilic tethers.

For the introduction of additional analysis protocols of tethered molecules, a method is presented to prepare functionalized, deuterated oligo(ethylene glycols) from ethylene glycol-d4. Partial oligomerization of ethylene glycol-d4 and conversion to ditosylates is accompanied by coupling reactions to prepare doubly benzyl protected oligo(ethylene glycols) with two to five repeating units. The tetramer bearing 16 deuteria was elaborated at both ends to eventually prepare 2,3-di-O-phytanyl-sn-glycerol-1-tetraethylene glycol-d,l-alpha-lipoic acid ester (DPTL), which bears a fully deuterated tetra(ethylene glycol) spacer group. Through linking of functionalized components, an analogue of DPTL possessing an octa(ethylene glycol) spacer group was prepared, both in deuterated and unlabeled form.

New method to measure packing densities of self-assembled thiolipid monolayers.

For a monolayer of 2,3-di-phytanyl-sn-glycerol-1-tetraethylene glycol-D,L-a-lipoic acid ester lipid (DPTL) self-assembled (SAM) at a gold electrode surface we propose a new method to determine the charge number per adsorbed molecule and the packing density (area per molecule) in the monolayer. The method relies on chronocoulometry to measure the charge density at the SAM covered gold electrode surface. Two series of measurements have to be performed. In the first series, charge densities are measured for a monolayer transferred from the air-solution to the metal-solution interface using the Langmuir-Blodgett (LB) technique. This series of measurements allows one to determine charge numbers per adsorbed DPTL molecule. The second series is performed using a gold electrode covered with a self-assembled monolayer. The charge densities obtained in this series are then used to calculate the packing density with the help of charge numbers per adsorbed DPTL determined in the first series. The area per adsorbed molecule determined by the new method was compared to the area per molecule determined by the popular reductive desorption method. The molecular area determined with the new method is about 20% larger than the area calculated from the van der Waals model, which is a physically reasonable result. In contrast, the popular reductive desorption method gives an area per molecule 20% lower than the minimum estimated based on a van der Waals model. This is a physically unreasonable result. It is also shown that the charge numbers per adsorbed molecule depend on the electrode potential and may assume values smaller than the number of electrons participating in the reductive desorption step. An explanation of the origin of the "partial charge numbers" is provided. We recommend the new method be used in future studies of thiol adsorption at metal surfaces.