Comparative Study of the Effect of Defects on Selective Adsorption of Butanol from Butanol/Water Binary Vapor Mixtures in Silicalite-1 Films.

A promising route for sustainable 1-butanol (butanol) production is ABE (acetone, butanol, ethanol) fermentation. However, recovery of the products is challenging because of the low concentrations obtained in the aqueous solution, thus hampering large-scale production of biobutanol. Membrane and adsorbent-based technologies using hydrophobic zeolites are interesting alternatives to traditional separation techniques (e.g., distillation) for energy-efficient separation of butanol from aqueous mixtures. To maximize the butanol over water selectivity of the material, it is important to reduce the number of hydrophilic adsorption sites. This can, for instance, be achieved by reducing the density of lattice defect sites where polar silanol groups are found. The density of silanol defects can be reduced by preparing the zeolite at neutral pH instead of using traditional synthesis solutions with high pH. In this work, binary adsorption of butanol and water in two silicalite-1 films was studied using in situ attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy under equal experimental conditions. One of the films was prepared in fluoride medium, whereas the other one was prepared at high pH using traditional synthesis conditions. The amounts of water and butanol adsorbed from binary vapor mixtures of varying composition were determined at 35 and 50 °C, and the corresponding adsorption selectivities were also obtained. Both samples showed very high selectivities (100-23 000) toward butanol under the conditions studied. The sample having low density of defects, in general, showed ca. a factor 10 times higher butanol selectivity than the sample having a higher density of defects at the same experimental conditions. This difference was due to a much lower adsorption of water in the sample with low density of internal defects. Analysis of molecular simulation trajectories provides insights on the local selectivities in the zeolite channel network and at the film surface.

Adsorption of Butanol and Water Vapors in Silicalite-1 Films with a Low Defect Density.

Pure silica zeolites are potentially hydrophobic and have therefore been considered to be interesting candidates for separating alcohols, e.g., 1-butanol, from water. Zeolites are traditionally synthesized at high pH, leading to the formation of intracrystalline defects in the form of silanol defects in the framework. These silanol groups introduce polar adsorption sites into the framework, potentially reducing the adsorption selectivity toward alcohols in alcohol/water mixtures. In contrast, zeolites prepared at neutral pH using the fluoride route contain significantly fewer defects. Such crystals should show a much higher butanol/water selectivity than crystals prepared in traditional hydroxide (OH-) media. Moreover, silanol groups are present at the external surface of the zeolite crystals; therefore, minimizing the external surface of the studied adsorbent is important. In this work, we determine adsorption isotherms of 1-butanol and water in silicalite-1 films prepared in a fluoride (F-) medium using in situ attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy. This film was composed of well intergrown, plate-shaped b-oriented crystals, resulting in a low external area. Single-component adsorption isotherms of 1-butanol and water were determined in the temperature range of 35-80 °C. The 1-butanol isotherms were typical for an adsorbate showing a high affinity for a microporous material and a large increase in the amount adsorbed at low partial pressures of 1-butanol. The Langmuir-Freundlich model was successfully fitted to the 1-butanol isotherms, and the heat of adsorption was determined. Water showed a very low affinity for the adsorbent, and the amounts adsorbed were very similar to previous reports for large silicalite-1 crystals prepared in a fluoride medium. The sample also adsorbed much less water than did a reference silicalite-1(OH-) film containing a high density of internal defects.The results show that silicalite-1 films prepared in a F- medium with a low density of defects and external area are very promising for the selective recovery of 1-butanol from aqueous solutions.

Colloidal Defect-Free Silicalite-1 Single Crystals: Preparation, Structure Characterization, Adsorption, and Separation Properties for Alcohol/Water Mixtures.

In this work, colloidal silicalite-1 single crystals are for the first time synthesized using fluoride as mineralizing agent at near neutral pH. SEM, TEM, DLS, XRD, solid-state (29)Si MAS NMR, and adsorption/desorption experiments using nitrogen, water, n-butanol, and ethanol as adsorbates were used to characterize the crystals. The single crystals have a platelike habit with a length of less than 170 nm and an aspect ratio (length/width) of about 1.2, and the thickness of the crystals is less than 40 nm. Compared with silicalite-1 crystals grown using hydroxide as mineralizing agent, the amount of structural defects in the lattice is significantly reduced and the hydrophobicity is increased. Membrane separation and adsorption results show that the synthesized defect-free crystals present high selectivity to alcohols from alcohol/water mixtures. The n-butanol/water adsorption selectivities were ca. 165 and 14 for the defect-free crystals and a reference sample containing defects, respectively, illustrating the improvement in n-butanol/water selectivity by eliminating the polar silanol defects.

Adsorption of water and butanol in silicalite-1 film studied with in situ attenuated total reflectance-Fourier transform infrared spectroscopy.

Biobutanol produced by, e.g., acetone-butanol-ethanol (ABE) fermentation is a promising alternative to petroleum-based chemicals as, e.g., solvent and fuel. Recovery of butanol from dilute fermentation broths by hydrophobic membranes and adsorbents has been identified as a promising route. In this work, the adsorption of water and butanol vapor in a silicalite-1 film was studied using in situ attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy to better understand the adsorption properties of silicalite-1 membranes and adsorbents. Single-component adsorption isotherms were determined in the temperature range of 35-120 °C, and the Langmuir model was successfully fitted to the experimental data. The adsorption of butanol is very favorable compared to that of water. When the silicalite-1 film was exposed to a butanol/water vapor mixture with 15 mol % butanol (which is the vapor composition of an aqueous solution containing 2 wt % butanol, a typical concentration in an ABE fermentation broth, i.e., the composition of the gas obtained from gas stripping of an ABE broth) at 35 °C, the adsorption selectivity toward butanol was as high as 107. These results confirm that silicalite-1 quite selectively adsorbs hydrocarbons from vapor mixtures. To the best of our knowledge, this is the first comprehensive study on the adsorption of water and butanol in silicalite-1 from vapor phase.