Laser all-ceramic crown removal and pulpal temperature--a laboratory proof-of-principle study.

The objective of this proof-of-principle laboratory pilot study was to evaluate the temperature increase in the pulp chamber in a worst case scenario during Er:YAG laser debonding of all-ceramic crowns. Twenty extracted molars were prepared to receive all-ceramic IPS E.max CAD full contour crowns. The crowns were bonded to the teeth with Ivoclar Multilink Automix. Times for laser debonding and temperature rise in the pulp chamber using micro-thermocouples were measured. The Er:YAG was used with 560 mJ/pulse. The irradiation was applied at a distance of 5 mm from the crown surface. Additional air-water spray for cooling was utilized. Each all-ceramic crown was successfully laser debonded with an average debonding time of 135 ± 35 s. No crown fractured, and no damage to the underlying dentin was detected. The bonding cement deteriorated, but no carbonization at the dentin/cement interface occurred. The temperature rise in the pulp chamber averaged 5.4° ± 2.2 °C. During 8 out of the 20 crown removals, the temperature rise exceeded 5.5 °C, lasting 5 to 43 s (average 18.8 ± 11.6 s). A temperature rise of 11.5 °C occurred only once, while seven times the temperature rise was limited to 6.8 ± 0.5 °C. Temperature rises above 5.5 °C occurred only when the laser was applied from one side and additional cooling from the side opposite the irradiation. Er:YAG laser energy can successfully be used to efficiently debond all-ceramic crowns from natural teeth. Temperature rises exceeding 5.5 °C only occur when an additional air/water cooling from a dental syringe is inaccurately directed. To avoid possible thermal damage and to allow further heat diffusion, clinically temperature-reduced water might be applied.

Occlusal considerations for implant restorations in the partially edentulous patient.

The type and frequency of complications associated with dental implants has changed during the past decade. As more-successful rates of osseointegration have resulted from improved surgical protocols and materials, the major complications have become restorative-related rather than surgery-related. Recent studies indicate that restorative complications with implant-retained restorations occur at rates of 10 percent to 77 percent over a three-year period. Many of the restorative complications can be minimized with careful treatment planning and coordination of care. However, because implants lack the stress release associated with a periodontal ligament, impact loading to restorative materials and the crestal bone remains potentially more damaging with implant-supported restorations. This article discusses the biomechanical implications of implant restorations and outlines occlusal considerations designed to decrease restorative complications.

The less than 7-mm edentulous mandible: the implant/overdenture reconstructive option.

The edentulous patient with a severely atrophic mandible (less than 7 mm in height) can be successfully restored with two endosseous implants and a clip-bar overdenture, with minimal morbidity. Two of the three cases reported illustrate the long-term potential of this treatment modality.

Failure load of acrylic resin denture teeth bonded to high impact acrylic resins.

STATEMENT OF PROBLEM: Techniques for bonding denture teeth to an acrylic resin denture base remain empirical, with little consensus from the literature, among clinicians, or among dental laboratories. PURPOSE: This study evaluated the failure load of acrylic resin teeth bonded to 2 high impact acrylic resins. METHODS AND MATERIAL: The ridge lap portion on 120 identical denture teeth were modified with 3 variables: (1) placing a diatoric, (2) using monomer to prewet the denture tooth, and (3) breaking the glaze. Variables were combined to form 6 groups of 10 teeth each, and processed with Lucitone 199 (Lucitone) or SR-Ivocap (Ivocap) acrylic resin. Data analysis included the use of a heterogeneous variance linear regression model. RESULTS: Mean (+/- SD) failure load ranged between 10.25 +/- 1.48 Kg to 28.43 +/- 11.05 Kg for the 6 Ivocap groups and 16.63 +/- 5.87 Kg to 28.05 +/- 5.35 Kg for the Lucitone groups. For Lucitone 199 acrylic resin, the highest failure loads resulted when the ridge lap was left with an intact glaze and did not have a diatoric, with no significant influence from the use of monomer. For Ivocap resin, the highest failure loads resulted when the ridge lap had a diatoric but did not have monomer placed, with no significant influence from glaze. CONCLUSION: Failure load of bonding highly cross-linked denture teeth to SR-Ivocap or Lucitone 199 acrylic resin was significantly influenced by modifications to the ridge lap before processing.

Crevicular fluid analysis around two failing dental implants: a clinical report.

The criteria for monitoring tissue health around endosseous implants remain subjective. Disagreement about which clinical measures of peri-implant health are of diagnostic value continues because of the complexity of the disease process and lack of validated measures of peri-implant health. Crevicular fluid analysis of various inflammatory mediators has been investigated as a means of providing objective criteria of tissue health. In this clinical report, the crevicular fluid levels of interleukin-1 beta (IL-1 beta), an inflammatory cytokine, were used to provide an objective measure of the peri-implant health and the effectiveness of treatment for a patient with two failing implants. The measurement of IL-1 beta may be an important supplement to clinical findings in establishing a diagnosis of peri-implantitis.

Incidence of various classes of removable partial dentures.

The purpose of a classification for removable partial dentures (RPDs) is to simplify identification and enhance its teaching. A classification also allows a longitudinal comparison of various classes of RPDs to determine whether the teaching of RPD design is consistent with the relative frequencies of RPD use. This study surveyed the types of removable partial dentures being fabricated in a regional dental laboratory and compared these findings with data from previous studies. Results indicate that mandibular RPDs are more common than maxillary RPDs and the class I mandibular RPD is the most common type of RPD for either dental arch. A palatal strap was the most frequently used maxillary major connector and a lingual bar was used three times more often than a lingual plate in the mandibular arch. Cast circumferential clasps were used twice as often as RPI clasp designs. The percentage of Kennedy class I RPDs was 40%, class II 33%, class III 18%, and class IV 9%. Comparisons with a previous study indicate the percentage of Kennedy class II has increased, whereas class I, class III and class IV RPDs have not changed significantly. Findings of the study indicate that the frequency of use of the various types of RPDs have changed in the past 30 years.

The effect of clinical remount procedures on the comfort and success of complete dentures.

Fifteen patients were treated with complete dentures in a routine manner that included a clinical remount. A second group of 15 was treated in the identical manner except that the clinical remount was not performed. The occlusal patterns of all dentures were recorded in the patient's mouths at delivery and again 1 week later by using a photoelastic membrane to provide a permanent record. The presence or absence of soreness was also noted for each patient during the week after delivery. Results indicate that clinical remounts significantly reduced the incidence of soreness, preserved the occlusal force, and reduced the changes in occlusal patterns of the dentures. Although both cusped and flat teeth were used in both treatment groups, no significant differences were noted in relation to either form on the basis of the indices studied.