The Effect of Changing the Angle of the Passenger Car Seat Backrest on the Head Trajectories of the 50th Percentile Male Dummy.

The aim of the study is to compare the head displacement of the KPSIT C50 dummy during a frontal collision at a speed of 20 km/h, along with the change in the angle of the car seat backrest. Passenger car manufacturers recommend setting the backrest angle of the car seat between 100 and 125 degrees. It should be noted that the driver's position is of great importance in the event of a collision injury. In the event of a rear-end collision, the position of the headrest of the car seat is an element that affects the degree of the driver's injuries. In extreme cases, incorrect positioning of the headrest, even at low speed, can lead to serious injuries to the cervical spine and even death. The article is part of a large-scale study on low-speed crash testing. The research problem concerned the influence of the seat backrest angle on the head displacement during a low-speed collision. The article compares the displacement of the head of the KPSIT C50 dummy during a series of crash tests, where the angle of the car seat backrest was changed. On the basis of the research, it was found that the optimal angle of the car seat backrest is 110 degrees. In addition, a preliminary analysis of the displacements of the dummy's head showed a high risk of whiplash injury in people sitting in a fully reclined seat.

Experimental Study on Longitudinal Acceleration of Urban Buses and Coaches in Different Road Maneuvers.

A vehicle's longitudinal acceleration is a parameter often used for determining vehicle motion dynamics. This parameter can also be used to evaluate driver behavior and passenger comfort analysis. The paper presents the results of longitudinal acceleration tests of city buses and coaches recorded during rapid acceleration and braking maneuvers. The presented test results demonstrate that longitudinal acceleration is significantly affected by road conditions and surface type. In addition, the paper presents the values of longitudinal accelerations of city buses and coaches during their regular operation. These results were obtained on the basis of registration of vehicle traffic parameters in a continuous and long-term manner. The test results showed that the maximum deceleration values recorded during the tests of city buses and coaches in real traffic conditions were much lower than the maximum deceleration values found during sudden braking maneuvers. This proves that the tested drivers in real conditions did not have to use sudden braking. The maximum positive acceleration values recorded in acceleration maneuvers were slightly higher than the acceleration values logged during the rapid acceleration tests on the track.

Comparison of Volunteers' Head Displacement with Computer Simulation-Crash Test with Low Speed of 20 km/h.

Recently, the automotive industry has used simulation programs much more often than experimental research. Computer simulations are more and more often used due to the repeatability of simulation conditions and the possibility of making modifications in simulation objects. Experimental and simulation studies carried out are aimed at developing a model of a simulation dummy adapted to both frontal and rear crash tests, taking into account changes in the moment of resistance in individual joints. The main purpose of the article is to reproduce a real crash test at a low speed of 20 km/h in a simulation program. For this purpose, a series of experimental crash tests with the participation of volunteers was carried out, and then a crash test with a dummy was simulated in the MSC ADAMS program. The experimental studies involved 100 volunteers who were divided into three percentile groups (C5, C50, C95). With the help of force sensors and a high-speed camera, crash tests of volunteers were recorded. The collected data from the force sensors made it possible to map the force in the seat belts. For low-speed crash tests, the displacement and acceleration of individual body parts of the dummy and volunteers can be measured using vision systems. The article identified head displacements of volunteers in the TEMA program based on a video analysis of a crash test film with a frequency of up to 2500 frames per second. The displacement of the simulation dummy's head in the MSC ADAMS program in the considered crash time interval from 0.0 to 0.4 s for all three percentile groups coincided with the head displacement of the volunteers during the experimental crash test.

Research and Analysis of the Propagation of Vertical Vibrations in the Arrangement of a Vehicle Seat-A Child's Seat.

This paper deals with the issues of the impact of vertical vibrations on a child seated in a child seat during a journey. Its purpose was to assess the impact of fastening the child seats and road conditions on the level of vibrations recorded on child seats. The paper describes the tested child seats, the methodology of the tests and the test apparatus included in the measuring track. The tests were carried out in real road conditions where the child seats were located on the rear seat of a passenger vehicle. One was attached with standard seat belts, and the other with the ISOFIX base. When driving on roads with three types of surface, the following vertical accelerations were measured: seat of the child seats, the rear seat of the vehicle and the ISOfix base. The recorded accelerations were first analyzed in the time domain and then in the frequency domain. Three indexes (r.m.s, rmq and VDV) were used to assess the vibration comfort. Research has shown that the classic method of fastening a child seat with standard seat belts is more advantageous in terms of vibration comfort. Calculated indicators confirmed the negative impact of separating the child seat from the rear seat of the vehicle using the IQ ISOFIX base.

Upper Limb Design of an Anthropometric Crash Test Dummy for Low Impact Rates.

The article presents the design of the upper limb joints of an anthropometric dummy intended for rear crash tests for low impact speeds. These joints represent the connection of the hand to the forearm, the forearm to the arm, and the arm to the shoulder. The designed joint is adapted to the construction of a dummy representing the 50th percentile male. The joints currently used on Hybrid III dummies require calibration after each crash test. The construction of the new joint ensures the appropriate strength of individual joint elements and the repeatable value of the joint characteristics without the need for frequent calibrations. The designed joints have the ability to set a variable stiffness characteristic, thanks to which it is possible to use this joint universally in dummies representing populations of other percentile sizes. The range of movement of the joints has been selected to reflect the range of mobility of the upper limb of an adult. The characteristics of the joints were compared with those used in the joints of the Hybrid III 50 percentile male dummy. Moreover, it should be noted that the constructed joints of the upper limb are made by hand; therefore, their comparison with the Hybrid III dummy shows some deviations in the moments of resistance. Making the joints with a 3D printer, taking into account the appropriate material, will ensure greater accuracy and will also result in joining the individual elements of the joint into a whole. The obtained results show slight differences between the moment of resistance in the joints of the constructed anthropometric dummy compared to the hybrid III dummy.