Failure Mechanisms at the Interfaces between Lithium Metal Electrodes and a Single-Ion Conducting Polymer Gel Electrolyte.

Polymer electrolytes have the potential to enable rechargeable lithium (Li) metal batteries. However, growth of nonuniform high surface area Li still occurs frequently and eventually leads to a short-circuit. In this study, a single-ion conducting polymer gel electrolyte is operated at room temperature in symmetric Li||Li cells. We use X-ray microtomography and electrochemical impedance spectroscopy (EIS) to study the cells. In separate experiments, cells were cycled at current densities of 0.1 and 0.3 mA cm-2 and short-circuits were obtained eventually after an average of approximately 240 cycles and 30 cycles, respectively. EIS reveals an initially decreasing interfacial resistance associated with electrodeposition of nonuniform Li protrusions and the concomitant increase in electrode surface area. X-ray microtomography images show that many of the nonuniform Li deposits at 0.1 mA cm-2 are related to the presence of impurities in both electrolyte and electrode phases. Protrusions are globular when they are close to electrolyte impurities but are moss-like when they appear near the impurities in the lithium metal. At long times, the interfacial resistance increases, perhaps due to additional impedance due to the formation of additional solid electrolyte interface (SEI) at the growing protrusions until the cells short. At 0.3 mA cm-2, large regions of the electrode-electrolyte interface are covered with mossy deposits. EIS reveals a decreasing interfacial resistance due to the increase in interfacial area up to short-circuit; the increase in interfacial impedance observed at the low current density is not observed. The results emphasize the importance of pure surfaces and materials on the microscopic scale and suggest that modification of interfaces and electrolyte may be necessary to enable uniform Li electrodeposition at high current densities.

Evolution of Protrusions on Lithium Metal Anodes Stabilized by a Solid Block Copolymer Electrolyte Studied Using Time-Resolved X-ray Tomography.

Growing demand for rechargeable batteries with higher energy densities has motivated research focused on enabling the lithium metal anode. A prominent failure mechanism in such batteries is short circuiting due to the uncontrolled propagation of lithium protrusions that often have a dendritic morphology. In this paper, the electrodeposition of metallic lithium through a rigid polystyrene-b-poly(ethylene oxide) (PS-b-PEO or SEO) block copolymer electrolyte was studied using hard X-ray microtomography. In this system, protrusions were approximately ellipsoidal globules: we take advantage of this simple geometry to quantify their growth as a function of polarization time and electrolyte salt concentration. The growth of 47 different globules was tracked with time to obtain average velocities of globule growth into the electrolyte. The globule diameter was a linear function of globule height in the electrolyte with a slope of about 6, independent of time and electrolyte salt concentration.

Impact of Salt Concentration on Nonuniform Lithium Electrodeposition through Rigid Block Copolymer Electrolytes.

There is a growing demand for higher energy density lithium batteries. One approach for addressing this demand is enabling lithium metal anodes. However, nucleation and growth of electronically conductive protrusions, which cause short circuits, prevent the use of this technology with liquid electrolytes. The use of rigid solid electrolytes such as polystyrene-b-poly(ethylene oxide) electrolytes is one solution. An additional requirement for practical cells is needed to use electrolytes with high salt concentration to maximize the flux of lithium ions in the cell. The first systematic study of the effect of salt concentration on the morphology of electrodeposited lithium through a rigid block copolymer electrolyte is presented. The nature, areal density, and morphologies of defective lithium deposits created during galvanostatic cycling of lithium-lithium symmetric cells were determined using hard X-ray microtomography. Cycle life decreases rapidly with increasing salt concentration. X-ray microtomography reveals the presence of multiglobular protrusions, which are nucleated at impurity particles at low salt concentrations; here, the areal density of defective lithium deposits was independent of salt concentration. At the highest salt concentration, this density increases abruptly by a factor of about 10, and defects were also nucleated at locations where no impurities were visible.