Third molar agenesis in individuals with supernumerary teeth.

OBJECTIVES: To explore the association between third molar agenesis and supernumerary tooth formation in a white-European population. MATERIALS AND METHODS: A record review in various orthodontic clinics identified 380 eligible white-European individuals, half of whom had non-syndromic permanent supernumerary teeth (122 males and 68 females, totalling 244 supernumerary teeth; median age: 13.1, iqr: 1.5 years), and the other half were age- and sex-matched controls with full dentition, excluding the third molars. Tooth sequences were identified in panoramic radiographs. RESULTS: In the supernumerary group, approximately 80% of the individuals had a single supernumerary tooth, followed by those having two additional teeth. In both groups, there was no sexual dimorphism in third molar agenesis severity. The prevalence of third molar agenesis in the supernumerary group was similar to that of the control group (28/190 = 14.7% in both groups; p = 1.0). In total, 53 third molars were missing in the supernumerary group (n = 190) compared to 67 in the control group (n = 190; p = .862). The ratio of bilateral to unilateral third molar agenesis was significantly lower in the supernumerary group than in the control group (1.0 vs. 3.7, respectively; p = .026). CONCLUSION: The presence of supernumerary teeth did not significantly alter the likelihood of third molar agenesis or its severity. Bilateral third molar agenesis was considerably less prevalent in individuals with supernumerary teeth compared to controls. The present novel findings have important clinical and developmental implications.

Supernumerary Tooth Patterns in Non-Syndromic White European Subjects.

Supernumerary teeth form at an incidence of about 3% in the population, with differences among races and various clinical consequences. Information on detailed patterns, and especially on white subjects, is scarce in the literature. Therefore, we aimed to investigate the patterns of non-syndromic permanent supernumerary teeth in a white European population. A record review was performed in different orthodontic clinics and identified 207 eligible individuals with 258 supernumerary teeth. Approximately 80% of the subjects had one supernumerary tooth, while 15% had two. Supernumerary tooth formation was more often evident in males (male/female: 1.65). However, there was no sexual dimorphism in its severity. The following pattern sequences, with decreasing prevalence order, were observed in the maxilla: 21 > 11 > 12 > 18 > 28 and in the mandible: 34 > 44 > 35 > 45 > 42. Supernumerary teeth were most often unilaterally present, without sexual dimorphism. In the maxilla, they were more often anteriorly present, whereas in the mandible, an opposite tendency was observed. Supernumerary teeth were consistently more often observed in the maxilla than in the mandible; 74% were impacted, 80% had normal orientation (13% horizontal, 7% inverted), and 53% had normal size. The present thorough supernumerary tooth pattern assessment enables a better understanding of this condition with clinical, developmental, and evolutionary implications.

Influence of different storage temperatures on the mechanical properties of NiTi, Cu-NiTi and SS orthodontic archwires: An in vitro study.

OBJECTIVE: Due to their exceptional temperature sensitivity, the mechanical properties of Nickel-titanium and Copper Nickel-titanium wires may be influenced by their storage temperature. This in turn may have clinical implications and may also affect the outcomes. This study analyzed the influence of storage temperatures on the mechanical properties of orthodontic wires in a laboratory setting. MATERIALS AND METHODS: Stainless steel (SS), Nickel-Titanium (NiTi), and three variants of Copper-NiTi (Cu-NiTi 27°C, 35°C and 40°C), 0.017×0.025 inches in size were analysed using a three-point bending test in a pre-heated chamber at 36°C. The orthodontic wires were stored for twenty-four hours before the mechanical testing at four different temperatures (5°, 22°, 36° and 60°C). RESULTS: The obtained results showed that the mechanical forces exerted by 27°C Copper-NiTi exhibit the most stable behaviour after having been stored at different temperatures, whereas 35°C Copper-NiTi showed the highest variability. As to be expected, Stainless steel shows no changes in its bending mechanical properties. CONCLUSION: Furthermore, the results of this investigation reflect the importance of controlling the storage temperature of orthodontic NiTi and Copper-NiTi wires tested in a research environment in order to avoid unexpected bias.

The effect of threshold level on bone segmentation of cranial base structures from CT and CBCT images.

The use of a single grey intensity threshold is one of the most straightforward and widely used methods to segment cranial base surface models from a 3D radiographic volume. In this study we used thirty Cone Beam Computer Tomography (CBCT) scans from three different machines and ten CT scans of growing individuals to test the effect of thresholding on the subsequently produced anterior cranial base surface models. From each scan, six surface models were generated using a range of voxel intensity thresholds. The models were then superimposed on a manually selected reference surface model, using an iterative closest point algorithm. Multivariate tests showed significant effects of the machine type, threshold value, and superimposition on the spatial position and the form of the created models. For both, CT and CBCT machines, the distance between the models, as well as the variation within each threshold category, was consistently increasing with the magnitude of difference between thresholds. The present findings highlight the importance of accurate anterior cranial base segmentation for reliable assessment of craniofacial morphology through surface superimposition or similar methods that utilize this anatomical structure as reference.