Hydrothermal Synthesis and Characterization of Zeolite A from Corn (Zea Mays) Stover Ash.

This study deals with the impact of calcination, alkalinity, and curing time parameters on the hydrothermal synthesis of zeolite A. The zeolite A sample, produced from corncob-stalk-and-leaves (corn stover) ash was characterized using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), thermo-gravimetric analysis (TGA), and scanning electron microscopy (SEM). The results showed that calcination, alkalinity, and curing time have significant effects on the crystallization and the morphology of zeolite A. In addition, these parameters also impacted the cation exchange capacity. Furthermore, the synthesized zeolite A was obtained using a calcination temperature of 500 °C within two hours of airflow, which is much lower than the temperatures previously reported in the literature for an agricultural waste and other waste materials. A fusion ratio of corn stover ash:NaOH of 1.0:1.5 and a curing time of nine hours were achieved. This is a major result as this curing time is much lower than those featured in other studies, which can reach up to twenty-four hours. In this paper, cubic crystal with rounded edge of zeolite A, having a cation exchange capacity of 2.439 meq Na+/g of synthesized anhydrous zeolite A, was obtained, which can be a good candidate for ion-exchange separation.

Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash.

Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC), which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1) their technical properties are comparable if not better; (2) they can be produced from industrial wastes; and (3) within reasonable constraints, their production requires less energy and emits significantly less CO2. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC) use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA) and coal bottom ash (CBA), and rice hull ash (RHA). The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF) for elemental and X-ray diffraction (XRD) for mineralogical composition. The raw materials' thermal stability and loss on ignition (LOI) were determined using thermogravimetric analysis (TGA) and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP) analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR), scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). Using a Scheffé-based mixture design, targeting applications with low thermal conductivity, light weight and moderate strength and allowing for a maximum of five percent by mass of rice hull ash in consideration of the waste utilization of all three components, it has been determined that an 85-10-5 by weight ratio of CFA-CBA-RHA activated with 80-20 by mass ratio of 12 M NaOH and sodium silicate (55% H2O, modulus = 3) produced geopolymers with a compressive strength of 18.5 MPa, a volumetric weight of 1660 kg/m³ and a thermal conductivity of 0.457 W/m-°C at 28-day curing when pre-cured at 80 °C for 24 h. For this study, the estimates of embodied energy and CO2 were all below 1.7 MJ/kg and 0.12 kg CO2/kg, respectively.

Degradation of polychlorinated biphenyls in aqueous solutions after UV-peroxide treatment: focus on toxicity of effluent to primary producers.

The combination of UV irradiation and hydrogen peroxide (UV-H(2)O(2)) was shown to be effective in treating water spiked with 2,2',4,4',5,5'-hexachlorobipheny (PCB 153), reducing its concentration by as much as 98%. To test the toxicity of the effluent, bioassays involving three species of primary producers were performed. Results showed the effluent exerting an adverse effect on the algae Scenedesmus bijugatus and the duckweed Lemna paucicostata. On the other hand, exposure of the mungbean Vigna radiata to the effluent revealed mostly no statistically significant adverse effect or growth stimulation. This suggested that on an exposure period of 96 h, higher forms of chlorophyll-bearing species such as plants are relatively unaffected by trace concentrations of PCBs and degradation products, while less differentiated species like algae and duckweeds are vulnerable.

Biodegradability and toxicity assessment of trans-chlordane photochemical treatment.

The removal of trans-chlordane (C(10)H(6)Cl(8)) from aqueous solutions was studied using UV, UV/H(2)O(2), UV/H(2)O(2)/Fe(2+), UV/TiO(2), or UV/TiO(2)/H(2)O(2) treatment using either UV/Vis blue lamps or UVC lamps (254 nm). H(2)O(2), FeSO(4) and TiO(2) were added at 1700, 456, and 2500 mgL(-1), respectively. trans-Chlordane was not significantly removed in non-irradiated controls and in samples irradiated with UV/Vis. It was also not removed in the absence of surfactant Triton X-114 added at 250 mgL(-1). In the presence of the surfactant, trans-chlordane concentration was reduced by 95-100% after 48 h of UVC and UVC/H(2)O(2) treatments and 70-80% after UVC/H(2)O(2)/Fe(2+), UVC/TiO(2) and UVC/H(2)O(2)/TiO(2) treatments. Based on these results, UVC, UVC/H(2)O(2) and UVC/TiO(2) treatments were further investigated. UVC treatment supported the highest pollutant removal (100% in 48 h), dechlorination efficiency (81% in 48 h), and detoxification to Lepidium sativum seed germination and activated sludge respiration although irradiated samples remained toxic to Chlorella vulgaris. Biodegradation of the UVC irradiated samples removed the source of algae toxicity but this could not be clearly attributed to the removal of trans-chlordane photoproducts because the surfactant interfered with the chemical and biological assays. Evidence was found that trans-chlordane was photodegraded through photolysis causing its successive dechlorination. trans-Chlordane removal was well described by a first order kinetic model at a rate of 0.21±0.01h(-1) at the 95% confidence interval.