Penetration Fracture Mechanism of Tungsten-Fiber-Reinforced Zr-Based Bulk Metallic Glasses Matrix Composite under High-Velocity Impact.

In order to adapt to the launch velocity of modern artillery, it is necessary to study the fracture mechanism of the high-velocity penetration of penetrators. Therefore, the penetration fracture mode of tungsten-fiber-reinforced Zr-based bulk metallic glass matrix composite (WF/Zr-MG) rods at a high velocity is studied. An experiment on WF/Zr-MG rods penetrating into rolled homogeneous armor steel (RHA) was carried out at 1470~1650 m/s. The experimental results show that the higher penetration ability of WF/Zr-MG rods not only results from their "self-sharpening" feature, but also due to the fact they have a longer quasi-steady penetration phase than tungsten alloy (WHA) rods. Above 1500 m/s, the penetration fracture mode of the WF/Zr-MG rod is the bending and backflow of tungsten fibers. Our theoretical calculation shows that the deformation mode of the Zr-based bulk metallic glass matrix (Zr-MG) is an important factor affecting the penetration fracture mode of the WF/Zr-MG rod. When the impact velocity increases from 1000 m/s to 1500 m/s, the deformation mode of Zr-MG changes from shear localization to non-Newtonian flow, leading to a change in the penetration fracture mode of the WF/Zr-MG rod from shear fracture to the bending and backflow of tungsten fibers.

Strain Rate and Porosity Effect on Mechanical Characteristics and Depolarization of Porous Poled PZT95/5 Ceramics.

Shock wave compression of poled PZT95/5 ceramics results in rapid depoling and a release of bound charge. Porous PZT95/5 ceramics are superior to dense ceramics in high-voltage breakdown resistance under shock-wave loading. In this article, the mechanical and electrical responses of porous poled PZT95/5 ceramics under uniaxial stresses at different strain rates were investigated using the servo-hydraulic MTS810 universal test machine and the improved split Hopkinson pressure bar system. The engineering stress vs. axial and radial engineering strain curves of porous poled PZT95/5 ceramics under different strain rates exhibit anomalous nonlinear behavior. The nonlinear behavior and depolarization mechanism of porous poled PZT95/5 were attributed to the domain switching and phase transformation. By comparing the stress-strain curves of the porosity porous poled PZT95/5 ceramics at different strain rates, an obvious strain rate sensitivity of mechanical behavior can be found, and the strain rate sensitivity decreases with the increase of porosity. The critical stress of domain switching and phase transformation and the strength increased with increasing strain rate. In addition, their normalized values showed a logarithmic relationship with the strain rate. Finally, we suggest that the maximum polarization released is nearly independent of stress state and strain rate, and it only depends on the porosity.

Semi-Crystalline Polymers Applied to Taylor Impact Test: Constitutive, Experimental and FEM Analysis.

Based on mechanical properties of Polyamide 66 (PA66) under complex loading conditions, a Drucker-Prager yield criterion was employed to characterize its yield behavior. Then, a one-dimensional model, which contains a viscoelastic regime and a viscoplastic regime, was introduced and converted into a three-dimensional constitutive model. The three-dimensional model was implemented into a LS-DYNA software, which was used to predict the dynamic response of PA66 under Taylor impact conditions, whose corresponding tests were conducted by gas gun and recorded by high-speed camera. By contrasting the simulation results and these of the corresponding tests, the deformed shapes including the residual length, the maximum diameter and the shape of the mushroom head of the PA66 bars were found to be similar to these obtained from the tests, which verified the accuracy of the three-dimensional constitutive model, and proved that the model was able to be applied to high-rate impact loading conditions.

Design of a wearable and shape-memory fibriform sensor for the detection of multimodal deformation.

A wearable and shape-memory strain sensor with a coaxial configuration is designed, comprising a thermoplastic polyurethane fiber as the core support, well-aligned and interconnected carbon nanotubes (CNTs) as conductive filaments, and polypyrrole (PPy) coating as the cladding layer. In this design, the stress relaxation between CNTs is well confined by the outer PPy cladding layer, which endows the fibriform sensor with good reliability and repeatability. The microcracks generated when the coaxial fiber is under strain guarantee the superior sensitivity of this fibriform sensor with a gauge factor of 12 at 0.1% strain, a wide detectable range (from 0.1% to 50% tensile strain), and the ability to detect multimodal deformation (tension, bending, and torsion) and human motions (finger bending, breathing, and phonation). In addition, due to its shape-memory characteristic, the sensing performance of the fibriform sensor is well retained after its shape recovers from 50% deformation and the fabric woven from the shape-memory coaxial fibers can be worn on the elbow joints in a reversible manner (original-enlarged-recovered) and fitted tightly. Thus, this sensor shows promising applications in wearable electronics.

Modification of the contact surfaces for improving the puncture resistance of laminar structures.

Uncovering energy absorption and surface effects of various penetrating velocities on laminar structures is essential for designing protective structures. In this study, both quasi-static and dynamic penetration tests were systematical conducted on the front surfaces of metal sheets coated with a graphene oxide (GO) solution and other media. The addition of a GO fluid film to the front impact surface aided in increasing the penetration strength, improving the failure extension and dissipating additional energy under a wide-range of indentation velocity, from 3.33 × 10-5 m/s to 4.42 m/s. The coated -surfaces improved the specific energy dissipation by approximately 15~40% relative to the dry-contact configuration for both single-layer and double-layer configurations, and specific energy dissipations of double-layer configurations were 20~30% higher than those of the single-layer configurations. This treatment provides a facile strategy in changing the contact state for improving the failure load and dissipate additional energy.