Enzyme-Catalyzed Polymerization of Kraft Lignin from Eucalyptus globulus: Comparison of Bacterial and Fungal Laccases Efficacy.

Kraft lignin, a side-stream from the pulp and paper industry, can be modified by laccases for the synthesis of high added-value products. This work aims to study different laccase sources, including a bacterial laccase from Streptomyces ipomoeae (SiLA) and a fungal laccase from Myceliophthora thermophila (MtL), for kraft lignin polymerization. To study the influence of some variables in these processes, a central composite design (CCD) with two continuous variables (enzyme concentration and reaction time) and three levels for each variable was used. The prediction of the behavior of the output variables (phenolic content and molecular weight of lignins) were modelled by means of response surface methodology (RSM). Moreover, characterization of lignins was performed by Fourier-transform infrared (FTIR) spectroscopy and different nuclear magnetic resonance (NMR) spectroscopy techniques. In addition, antioxidant activity was also analyzed. Results showed that lignin polymerization (referring to polymerization as lower phenolic content and higher molecular weight) occurred by the action of both laccases. The enzyme concentration was the most influential variable in the lignin polymerization reaction within the range studied for SiLA laccase, while the most influential variable for MtL laccase was the reaction time. FTIR and NMR characterization analysis corroborated lignin polymerization results obtained from the RSM.

NMR Study on Laccase Polymerization of Kraft Lignin Using Different Enzymes Source.

The usage of laccases is a sustainable and environmentally friendly approach to modifying the Kraft lignin structure for use in certain applications. However, the inherent structure of Kraft lignin, as well as that resulting from laccase modification, still presents challenges for fundamental comprehension and successful lignin valorization. In this study, bacterial and fungal laccases were employed to modify eucalypt Kraft lignin. To evaluate the type and range of the chemical and structural changes of laccase-treated lignins, different NMR techniques, including solution 1H and 2D NMR (heteronuclear single quantum correlation (HSQC)), and solid-state 13C NMR, were applied. Size exclusion chromatography and infrared spectroscopy were also used. Interestingly, HSQC analysis showed substantial changes in the oxygenated aliphatic region of lignins, showing an almost complete absence of signals corresponding to side-chains due to laccase depolymerization. Simultaneously, a significant loss of aromatic signals was observed by HSQC and 1H NMR, which was attributed to a deprotonation of the lignin benzenic rings due to polymerization/condensation by laccase reactions. Then, condensed structures, such as α-5', 5-5', and 4-O-5', were detected by HSQC and 13C NMR, supporting the increment in molecular weight, as well as the phenolic content reduction determined in lignins.

Different Kraft lignin sources for electrospun nanostructures production: Influence of chemical structure and composition.

This work focuses on the structural features and physicochemical properties of different Kraft lignins and how they can influence the electrospinning process to obtain nanostructures. Structural features of Kraft lignins were characterized by nuclear magnetic resonance, size exclusion chromatography, fourier-transform infrared spectroscopy, and thermal analysis, whereas chemical composition was analyzed by standard method. The addition of cellulose acetate (CA) improves the electrospinning process of Kraft lignins (KL). Thus, solutions of KL/CA at 30 wt% with a KL:CA weight ratio of 70:30 were prepared and then physicochemical and rheologically characterized. The morphology of electrospun nanostructures depends on the intrinsic properties of the solutions and the chemical structure and composition of Kraft lignins. Then, surface tension, electrical conductivity and viscosity of eucalypt/CA and poplar/CA solutions were suitable to obtain electrospun nanostructures based on uniform cross-linked nanofibers with a few beaded fibers. It could be related with the higher purity and higher linear structure, phenolic content and S/G ratios of lignin samples. However, the higher values of electrical conductivity and viscosity of OTP/CA solutions resulted in electrospun nanostructure with micro-sized particles connected by thin fibers, due to a lower purity, S/G ratio and phenolic content and higher branched structure in OTP lignin.

New System of Shrinkage Measurement through Cement Mortars Drying.

Cement mortar is used as a conglomerate in the majority of construction work. There are multiple variants of cement according to the type of aggregate used in its fabrication. One of the major problems that occurs while working with this type of material is the excessive loss of moisture during cement hydration (setting and hardening), known as shrinkage, which provokes a great number of construction pathologies that are difficult to repair. In this way, the design of a new sensor able to measure the moisture loss of mortars at different age levels is useful to establish long-term predictions concerning mortar mass volume loss. The purpose of this research is the design and fabrication of a new capacitive sensor able to measure the moisture of mortars and to relate it with the shrinkage.

Measurement of Moisture in Wood for Application in the Restoration of Old Buildings.

There are many historic buildings whose construction is based on timber frame walls. Most buildings built during the nineteenth and early twentieth centuries were based on timber frame walls with vertical support elements. These timber frame elements are affected by their moisture content and by the passage of time. If the interaction of the timber frame walls with hygrothermal fluctuations were known, the maintenance of these buildings could be improved significantly. To determine the moisture content of wood there are two types of meters on the market: on the one hand, capacitance meters which consist of two side ends and where the moisture content is measured locally between two peaks. On the other hand, there are meters based on the variation of electromagnetic transmittance of timber, which depends on the moisture of timber. The second ones are very expensive and difficult to handle. This work presents a new non-intrusive capacitive sensor that measures the global moisture content in a section of the timber frame walls and therefore its accuracy is similar to the accuracy that can be obtained with electromagnetic transmittance meters. Additionally, as it is a capacitive sensor, it is low cost and easy to operate.

Influence of process variables on the properties of laccase biobleached pulps.

A laccase stage can be used as a pre-treatment of a standard chemical bleaching sequence to reduce environmental concerns associated to this process. The importance of each independent variable and its influence on the properties of the bleached pulp have been studied in depth in this work, using an adaptive network-based fuzzy inference system (ANFIS) with four independent variables (laccase, buffer, mediator and oxygen) as input. Eucalyptus globulus kraft pulp was biobleached using a laccase from Pycnoporus sanguineus and a natural mediator (acetosyringone). Later, an alkaline extraction and a hydrogen peroxide treatment were applied. Most biobleaching processes showed a decrease in kappa number and an increase in brightness with no significant impact on the viscosity values, compared with the control. Oxygen was the variable with the smallest influence on the final pulp properties while the laccase and buffer solution showed a significant influence.