Tunable millimeter and sub-millimeter spectral response of textile metamaterial via resonant states.

We report on a new textile metamaterial created by adding metal wires directly into the polymer yarn. Split-ring resonator-like extended states are created. Simulations revealed that the extended states can be easily tuned via the geometry. Measurements of the transmittance spectrum as a function of the polarization angle in the low terahertz range were also performed and these peaks were ascribed to a polarization-dependent resonator model. The fabrics are viable candidates for flexible and deformable gigahertz and terahertz-enabled metamaterials.

Terahertz inverse synthetic aperture radar (ISAR) imaging with a quantum cascade laser transmitter.

A coherent transceiver using a THz quantum cascade (TQCL) laser as the transmitter and an optically pumped molecular laser as the local oscillator has been used, with a pair of Schottky diode mixers in the receiver and reference channels, to acquire high-resolution images of fully illuminated targets, including scale models and concealed objects. Phase stability of the received signal, sufficient to allow coherent image processing of the rotating target (in azimuth and elevation), was obtained by frequency-locking the TQCL to the free-running, highly stable optically pumped molecular laser. While the range to the target was limited by the available TQCL power (several hundred microwatts) and reasonably strong indoor atmospheric attenuation at 2.408 THz, the coherence length of the TQCL transmitter will allow coherent imaging over distances up to several hundred meters. Image data obtained with the system is presented.

Characterization of roughness parameters of metallic surfaces using terahertz reflection spectra.

This paper reports on the effect of random Gaussian roughness with rms roughness values of 5-20 microm on the terahertz reflection spectra of metallic aluminum surfaces using Fourier transform IR spectroscopy. By comparing experimental data with a theoretical model based on the Kirchhoff approximation, the rms roughness of a surface is accurately determined. The rms roughness determined by this method is in good agreement with the rms roughness measured using a stylus surface profilometer. In addition, we demonstrate that this method can be used to clearly resolve rough surfaces that differ in rms roughness by approximately 1 microm.

Frequency stabilization of a single mode terahertz quantum cascade laser to the kilohertz level.

A simple analog locking circuit was shown to stabilize the beat signal between a 2.408 THz quantum cascade laser and a CH(2)DOH THz CO(2) optically pumped molecular laser to 3-4 kHz (FWHM). This is approximately a tenth of the observed long-term (t approximately sec) linewidth of the optically pumped laser showing that the feedback loop corrects for much of the mechanical and acoustic-induced frequency jitter of the gas laser. The achieved stability should be sufficient to enable the use of THz quantum cascade lasers as transmitters in short-range coherent transceivers.

Terahertz sideband-tuned quantum cascade laser radiation.

A compact, tunable, narrowband terahertz source was demonstrated by mixing a single longitudinal mode 2.408 THz, free running quantum cascade laser with a 2-20 GHz microwave sweeper in a conventional corner-cube-mounted Schottky diode. The sideband spectra were characterized with a Fourier transform spectrometer, and the radiation was tuned through several D(2)O rotational transitions to estimate the longer term (t > or = several sec) bandwidth of the source. A spectral resolution of 2 MHz in CW regime was observed.

Transformation of the multimode terahertz quantum cascade laser beam into a Gaussian, using a hollow dielectric waveguide.

We demonstrate that a short hollow dielectric tube can act as a dielectric waveguide and transform the multimode, highly diverging terahertz quantum cascade laser beam into the lowest order dielectric waveguide hybrid mode, EH(11), which then couples efficiently to the free-space Gaussian mode, TEM(00). This simple approach should enable terahertz quantum cascade lasers to be employed in applications where a spatially coherent beam is required.

Wet-etch optimization of free-standing terahertz frequency-selective structures.

Free-standing frequency-selective surfaces consisting of approximately 10-microm-thick copper films with cross-aperture arrays are found to be tunable toward lower frequencies by means of wet chemical etching. Center frequencies were tuned from 1.57 to 1.53 THz while maintaining high transmittance. Wet etching also adjusts bandwidth, peak transmittance, and sidelobe transmittance. The advantage of the wet-etch technique is demonstrated by employment of these devices as bandpass filters for difluoromethane-based terahertz lasers. Adjustment in aperture dimensions because of etching results in suppression of a competing laser line (133.93 microm) by 15 dB while maintaining high transmittance at the operating wavelength of 192.06 microm.