Engineering Surface Oxygenated Functionalities on Commercial Carbon toward Ultrafast Sodium Storage in Ether-Based Electrolytes.

The pursuit of a high-capacity anode material has been urgently required for commercializing sodium-ion batteries with a high energy density and an improved working safety. In the absence of thermodynamically stable sodium intercalated compounds with graphite, constructing nanostructures with expanded interlayer distances is still the mainstream option for developing high-performance carbonaceous anodes. In this regard, a surface-functionalized and pore-forming strategy through a facile CO2 thermal etching route was rationally adopted to engineer negligible oxygenated functionalities on commercial carbon for boosting the sodium storage process. Benefitted from the abundant ionic/electronic pathways and more active reaction sites in the microporous structure with noticeable pseudocapacitive behaviors, the functionalized porous carbon could achieve a highly reversible capacity of 505 mA h g-1 at 50 mA g-1, an excellent rate performance of 181 mA h g-1 at 16,000 mA g-1, and an exceptional rate cycle stability of 176 mA h g-1 at 3200 mA g-1 over 1000 cycles. These outstanding electrochemical properties should be ascribed to a synergistic mechanism, fully utilizing the graphitic and amorphous structures for synchronous intercalations of sodium ions and solvated sodium ion compounds, respectively. Additionally, the controllable generation and evolution of a robust but thin solid electrolyte interphase film with the emergence of obvious capacitive reactions on the defective surface, favoring the rapid migration of sodium ions and solvated species, also contribute to a remarkable electrochemical performance of this porous carbon black.

Soft x-ray spectroscopy of high pressure liquid.

We describe a new experimental technique that allows for soft x-ray spectroscopy studies (∼100-1000 eV) of high pressure liquid (∼100 bars). We achieve this through a liquid cell with a 100 nm-thick Si3N4 membrane window, which is sandwiched by two identical O-rings for vacuum sealing. The thin Si3N4 membrane allows soft x-rays to penetrate, while separating the high-pressure liquid under investigation from the vacuum required for soft x-ray transmission and detection. The burst pressure of the Si3N4 membrane increases with decreasing size and more specifically is inversely proportional to the side length of the square window. It also increases proportionally with the membrane thickness. Pressures > 60 bars could be achieved for 100 nm-thick square Si3N4 windows that are smaller than 65 µm. However, above a certain pressure, the failure of the Si wafer becomes the limiting factor. The failure pressure of the Si wafer is sensitive to the wafer thickness. Moreover, the deformation of the Si3N4 membrane is quantified using vertical scanning interferometry. As an example of the performance of the high-pressure liquid cell optimized for total-fluorescence detected soft x-ray absorption spectroscopy (sXAS), the sXAS spectra at the Ca L edge (∼350 eV) of a CaCl2 aqueous solution are collected under different pressures up to 41 bars.

Large Charge-Transfer Energy in LiFePO4 Revealed by Full-Multiplet Calculation for the Fe L3 -edge Soft X-ray Emission Spectra.

We analyzed the Fe 3d electronic structure in LiFePO4 /FePO4 (LFP/FP) nanowire with a high cyclability by using soft X-ray emission spectroscopy (XES) combined with configuration-interaction full-multiplet (CIFM) calculation. The ex situ Fe L2,3 -edge resonant XES (RXES) spectra for LFP and FP are ascribed to oxidation states of Fe2+ and Fe3+ , respectively. CIFM calculations for Fe2+ and Fe3+ states reproduced the Fe L3 RXES spectra for LFP and FP, respectively. In the calculations for both states, the charge-transfer energy was considerably larger than those for typical iron oxides, indicating very little electron transfer from the O 2p to Fe 3d orbitals and a weak hybridization on the Fe-O bond during the charge-discharge reactions.

X-ray-Induced Fragmentation of Imidazolium-Based Ionic Liquids Studied by Soft X-ray Absorption Spectroscopy.

We investigated the X-ray absorption spectroscopy (XAS) fingerprint of EMImTFSI ionic liquid (IL) and its fragmentation products created by X-ray irradiation. To accomplish this, we used an open geometry where an IL droplet is directly exposed in the vacuum chamber and an enclosed geometry where the IL is confined in a cell covered by an X-ray transparent membrane. In the open geometry, the XAS signature was stable and consistent with experimental and theoretical spectra reported in the literature. In contrast, when the IL is enclosed, its XAS evolves continuously under X-ray illumination due to the accumulation of volatile fragmentation products inside the closed cell, while they evaporate in the open geometry. The changes in the XAS from the core levels of relevant elements (C, N, S, F) together with density functional theory calculations allowed us to identify the chemical nature of the fragment products and the chemical bonds most vulnerable to rupture under soft X-ray irradiation.

High-efficiency in situ resonant inelastic x-ray scattering (iRIXS) endstation at the Advanced Light Source.

An endstation with two high-efficiency soft x-ray spectrographs was developed at Beamline 8.0.1 of the Advanced Light Source, Lawrence Berkeley National Laboratory. The endstation is capable of performing soft x-ray absorption spectroscopy, emission spectroscopy, and, in particular, resonant inelastic soft x-ray scattering (RIXS). Two slit-less variable line-spacing grating spectrographs are installed at different detection geometries. The endstation covers the photon energy range from 80 to 1500 eV. For studying transition-metal oxides, the large detection energy window allows a simultaneous collection of x-ray emission spectra with energies ranging from the O K-edge to the Ni L-edge without moving any mechanical components. The record-high efficiency enables the recording of comprehensive two-dimensional RIXS maps with good statistics within a short acquisition time. By virtue of the large energy window and high throughput of the spectrographs, partial fluorescence yield and inverse partial fluorescence yield signals could be obtained for all transition metal L-edges including Mn. Moreover, the different geometries of these two spectrographs (parallel and perpendicular to the horizontal polarization of the beamline) provide contrasts in RIXS features with two different momentum transfers.

Correlation between the O 2p Orbital and Redox Reaction in LiMn0.6 Fe0.4 PO4 Nanowires Studied by Soft X-ray Absorption.

The changes in the electronic structure of LiMn0.6 Fe0.4 PO4 nanowires during discharge processes were investigated by using ex situ soft X-ray absorption spectroscopy. The Fe L-edge X-ray absorption spectrum attributes the potential plateau at 3.45 V versus Li/Li+ of the discharge curve to a reduction of Fe3+ to Fe2+ . The Mn L-edge X-ray absorption spectra exhibit the Mn2+ multiplet structure throughout the discharge process, and the crystal-field splitting was slightly enhanced upon full discharge. The configuration-interaction full-multiplet calculation for the X-ray absorption spectra reveals that the charge-transfer effect from O 2p to Mn 3d orbitals should be considerably small, unlike that from the O 2p to Fe 3d orbitals. Instead, the O K-edge X-ray absorption spectrum shows a clear spectral change during the discharge process, suggesting that the hybridization of O 2p orbitals with Fe 3d orbitals contributes essentially to the reduction.

Understanding the magnetic interaction between intrinsic defects and impurity ions in room-temperature ferromagnetic Mg1-xFexO thin films.

Understanding the nature and characteristics of the intrinsic defects and impurities in the dielectric barrier separating the ferromagnetic electrodes in a magnetic tunneling junction is of great importance for understanding the often observed 'barrier-breakdown' therein. In this connection, we present herein systematic experimental (SQUID and synchrotron-radiation-based x-ray absorption spectroscopy) and computational studies on the electronic and magnetic properties of Mg1-xFexO thin films. Our studies reveal: (i) defect aggregates comprised of basic and trimer units (Fe impurity coupled to 1 or 2 Mg vacancies) and (ii) existence of two competing magnetic orders, defect- and dopant-induced, with spin densities aligning anti-parallel if the trimer is present in the oxide matrix. These findings open up new avenues for designing tunneling barriers with high endurance and tunneling effect upon tuning the concentration/distribution of the two magnetic orders.

Amorphous V2O5-P2O5 as high-voltage cathodes for magnesium batteries.

A deep investigation of amorphous V2O5-P2O5 powders for magnesium batteries communicates the vital properties to achieving the superior electrochemical performance at a 75 : 25 V2O5 : P2O5 molar ratio. The manipulation of the inter-layer spacing and amorphization of V2O5 can enhance Mg(2+) diffusion and afford a cathode with high-voltage reversibility.

Probing the Interfacial Interaction in Layered-Carbon-Stabilized Iron Oxide Nanostructures: A Soft X-ray Spectroscopic Study.

We have stabilized the iron oxide nanoparticles (NPs) of various sizes on layered carbon materials (Fe-oxide/C) that show excellent catalytic performance. From the characterization of X-ray absorption spectroscopy (XAS), X-ray emission spectroscopy (XES), scanning transmission X-ray microscopy (STXM) and X-ray magnetic circular dichroism spectroscopy (XMCD), a strong interfacial interaction in the Fe-oxide/C hybrids has been observed between the small iron oxide NPs and layered carbon in contrast to the weak interaction in the large iron oxide NPs. The interfacial interaction between the NPs and layered carbon is found to link with the improved catalytic performance. In addition, the Fe L-edge XMCD spectra show that the large iron oxide NPs are mainly γ-Fe2O3 with a strong ferromagnetic property, whereas the small iron oxide NPs with strong interfacial interaction are mainly α-Fe2O3 or amorphous Fe2O3 with a nonmagnetic property. The results strongly suggest that the interfacial interaction plays a key role for the catalytic performance, and the experimental findings may provide guidance toward rational design of high-performance catalysts.

Capturing interfacial photoelectrochemical dynamics with picosecond time-resolved X-ray photoelectron spectroscopy.

Time-resolved core-level spectroscopy using laser pulses to initiate and short X-ray pulses to trace photoinduced processes has the unique potential to provide electronic state- and atomic site-specific insight into fundamental electron dynamics in complex systems. Time-domain studies using transient X-ray absorption and emission techniques have proven extremely valuable to investigate electronic and structural dynamics in isolated and solvated molecules. Here, we describe the implementation of a picosecond time-resolved X-ray photoelectron spectroscopy (TRXPS) technique at the Advanced Light Source (ALS) and its application to monitor photoinduced electron dynamics at the technologically pertinent interface formed by N3 dye molecules anchored to nanoporous ZnO. Indications for a dynamical chemical shift of the Ru3d photoemission line originating from the N3 metal centre are observed ∼30 ps after resonant HOMO-LUMO excitation with a visible laser pump pulse. The transient changes in the TRXPS spectra are accompanied by a characteristic surface photovoltage (SPV) response of the ZnO substrate on a pico- to nanosecond time scale. The interplay between the two phenomena is discussed in the context of possible electronic relaxation and recombination pathways that lead to the neutralisation of the transiently oxidised dye after ultrafast electron injection. A detailed account of the experimental technique is given including an analysis of the chemical modification of the nano-structured ZnO substrate during extended periods of solution-based dye sensitisation and its relevance for studies using surface-sensitive spectroscopy techniques.

Understanding the electrochemical mechanism of K-αMnO2 for magnesium battery cathodes.

Batteries based on magnesium are an interesting alternative to current state-of-the-art lithium-ion systems; however, high-energy-density cathodes are needed for further development. Here we utilize TEM, EDS, and EELS in addition to soft-XAS to determine electrochemical magnesiation mechanism of a high-energy density cathode, K-αMnO2. Rather than following the typical insertion mechanism similar to Li(+), we propose the gradual reduction of K-αMnO2 to form Mn2O3 then MnO at the interface of the cathode and electrolyte, finally resulting in the formation of K-αMnO2@(Mg,Mn)O core-shell product after discharge of the battery. Understanding the mechanism is a vital guide for future magnesium battery cathodes.

An ultra-high vacuum electrochemical flow cell for in situ/operando soft X-ray spectroscopy study.

An in situ flow electrochemical cell has been designed and fabricated to allow better seal under UHV chamber thus to achieve a good signal to noise ratio in fluorescence yield detection of X-ray absorption spectra for spectroelectrochemical study. The cell also stabilizes the thin silicon nitride membrane window in an effective manner so that the liquid cell remains intact during X-ray absorption experiments. With the improved design of the liquid cell, electrochemical experiments such as cyclic voltammetry have been performed for 10 cycles with a good stability of sample window. Also an operando electrochemical experiment during photoelectrochemistry has been performed on n-type hematite electrode deposited on silicon nitride window. The experiment allows us to observe the formation of two extra electronic transitions before pre edge of O K-edge spectra.

Disorder-induced room temperature ferromagnetism in glassy chromites.

We report an unusual robust ferromagnetic order above room temperature upon amorphization of perovskite [YCrO3] in pulsed laser deposited thin films. This is contrary to the usual expected formation of a spin glass magnetic state in the resulting disordered structure. To understand the underlying physics of this phenomenon, we combine advanced spectroscopic techniques and first-principles calculations. We find that the observed order-disorder transformation is accompanied by an insulator-metal transition arising from a wide distribution of Cr-O-Cr bond angles and the consequent metallization through free carriers. Similar results also found in YbCrO3-films suggest that the observed phenomenon is more general and should, in principle, apply to a wider range of oxide systems. The ability to tailor ferromagnetic order above room temperature in oxide materials opens up many possibilities for novel technological applications of this counter intuitive effect.

Anisotropic charge-transfer effects in the asymmetric Fe(CN)5NO octahedron of sodium nitroprusside: a soft X-ray absorption spectroscopy study.

The electronic structure of Na2[Fe(CN)5NO]·2H2O (sodium nitroprusside: SNP) was investigated by using soft X-ray absorption (XA) spectroscopy. The Fe L2,3-edge XA spectrum of SNP exhibited distinct and very large satellite peaks for L3 and L2 regions, which is different from the spectra of hexacyanoferrates and the other iron compounds. A configuration-interaction full-multiplet calculation, in which the ligand molecular orbitals for the C4v symmetry were taken into account, revealed the Fe(2+) low-spin state with very strong effects of metal-to-ligand charge-transfer from the Fe 3d to NO 2p orbitals.

Effect of Al3+ co-doping on the dopant local structure, optical properties, and exciton dynamics in Cu+-doped ZnSe nanocrystals.

The dopant local structure and optical properties of Cu-doped ZnSe (ZnSe:Cu) and Cu and Al co-doped ZnSe (ZnSe:Cu,Al) nanocrystals (NCs) were studied with an emphasis on understanding the impact of introducing Al as a co-dopant. Quantum-confined NCs with zinc blende crystal structure and particle size of 6 ± 0.6 Å were synthesized using a wet chemical route. The local structure of the Cu dopant, studied by extended X-ray absorption fine structure, indicated that Cu in ZnSe:Cu NCs occupies a site that is neither substitutional nor interstitial and is adjacent to a Se vacancy. Additionally, we estimated that approximately 25 ± 8% of Cu was located on the surface of the NC. Al(3+) co-doping aids in Cu doping by accounting for the charge imbalance originated by Cu(+) doping and consequently reduces surface Cu doping. The Cu ions remain distorted from the center of the tetrahedron to one of the triangular faces. The lifetime of the dopant-related photoluminescence was found to increase from 550 ± 60 to 700 ± 60 ns after Al co-doping. DFT calculations were used to obtain the density of states of a model system to help explain the optical properties and dynamics processes observed. This study demonstrates that co-doping using different cations with complementary oxidation states is an effective method to enhance optical properties of doped semiconductor NCs of interest for various photonics applications.

Towards understanding the electronic structure of Fe-doped CeO2 nanoparticles with X-ray spectroscopy.

This study reports on the electronic structure of Fe-doped CeO2 nanoparticles (NPs), determined by coupled X-ray absorption spectroscopy and X-ray emission spectroscopy. A comparison of the local electronic structure around the Ce site with that around the Fe site indicates that the Fe substitutes for the Ce. The oxygen K-edge spectra that originated from the hybridization between cerium 4f and oxygen 2p states are sensitive to the oxidation state and depend strongly on the concentration of Fe doping. The Ce M(4,5)-edges and the Fe L(2,3)-edges reveal the variations of the charge states of Ce and Fe upon doping, respectively. The band gap is further obtained from the combined absorption-emission spectrum and decreased upon Fe doping, implying Fe doping introduces vacancies. The oxygen vacancies are induced by Fe doping and the spectrum reveals the charge transfer between Fe and Ce. Fe(3+) doping has two major effects on the formation of ferromagnetism in CeO2 nanoparticles. The first, at an Fe content of below 5%, is that the formation of Fe(3+)-Vo-Ce(3+) introduces oxygen deficiencies favoring ferromagnetism. The other, at an Fe content of over 5%, is the formation of Fe(3+)-Vo-Fe(3+), which favors antiferromagnetism, reducing the Ms. The defect structures Fe(3+)-Vo-Ce(3+) and Fe(3+)-Vo-Fe(3+) are crucial to the magnetism in these NPs and the change in Ms can be described as the effect of competitive interactions of magnetic polarons and paired ions.

Properties of disorder-engineered black titanium dioxide nanoparticles through hydrogenation.

The recent discovery of "black" TiO2 nanoparticles with visible and infrared absorption has triggered an explosion of interest in the application of TiO2 in a diverse set of solar energy systems; however, what a black TiO2 nanoparticle really is remains a mystery. Here we elucidate more properties and try to understand the inner workings of black TiO2 nanoparticles with hydrogenated disorders in a surface layer surrounding a crystalline core. Contrary to traditional findings, Ti(3+) here is not responsible for the visible and infrared absorption of black TiO2, while there is evidence of mid-gap states above the valence band maximum due to the hydrogenated, engineered disorders. The hydrogen atoms, on the other hand, can undergo fast diffusion and exchange. The enhanced hydrogen mobility may be explained by the presence of the hydrogenated, disordered surface layer. This unique structure thus may give TiO2, one of the most-studied oxide materials, a renewed potential.

Electronic structure and chemical bonding of a graphene oxide-sulfur nanocomposite for use in superior performance lithium-sulfur cells.

We have investigated the chemical bonding and electronic structure of a graphene oxide-sulfur (GO-S) nanocomposite by X-ray Photoelectron Spectroscopy (XPS), Near-edge X-ray Absorption Fine Structure (NEXAFS), and X-ray Emission Spectroscopy (XES). The nanocomposite, synthesized by a chemical reaction-deposition approach followed by low temperature thermal treatment, is composed of a thin and uniform sulfur film anchored on a graphene oxide (GO) sheet. The GO is partially reduced during the chemical synthesis process, resulting in the appearance of a C-H bond and an increase in the ordering of GO sheets. The moderate chemical interactions between sulfur and GO can preserve the intrinsic electronic structure of GO, and on the other hand, immobilize the sulfur on the GO sheets, which should be responsible for the excellent electrochemical performance of the lithium-sulfur cells by using the GO-S nanocomposite as the cathode material.

X-ray absorption, photoemission spectroscopy, and Raman scattering analysis of amorphous tantalum oxide with a large extent of oxygen nonstoichiometry.

The electronic structure and modification of the local interatomic structure of a reactive sputtered amorphous tantalum oxide (a-TaO(x)) thin film with the variation of oxygen nonstoichiometry, x in a-TaO(x) have been investigated by X-ray absorption spectroscopy (XAS), X-ray photoemission spectroscopy (XPS), Raman scattering spectroscopy, and Rutherford back scattering spectroscopy. A parallel chemical shift of Ta4f(7/2) and O1s core levels observed with the variation of x indicates the Fermi level shift by reduction and oxidation in the framework of the rigid band model. Extended X-ray absorption fine structure (EXAFS) suggests both the increase of average coordination number of the first Ta-O shell in polyhedra and a considerable reduction of the average Ta-O bond length with the increase of x. The relative intensity of Raman shift peaks at 670 cm(-1) and 815 cm(-1), corresponding to Ta-O stretching of TaO(6) octahedra and TaO(5) probably with a pyramidal form, respectively, drastically changes between x = 2.47 to 1.86, suggesting the change in the predominant polyhedron from TaO(6) to TaO(5) with a modification in multiplicity of oxygen by the reorganization of the polyhedral network.

Pentavalent and tetravalent uranium selenides, Tl3Cu4USe6 and Tl2Ag2USe4: syntheses, characterization, and structural comparison to other layered actinide chalcogenide compounds.

The compounds Tl(3)Cu(4)USe(6) and Tl(2)Ag(2)USe(4) were synthesized by the reaction of the elements in excess TlCl at 1123 K. Both compounds crystallize in new structure types, in space groups P2(1)/c and C2/m, respectively, of the monoclinic system. Each compound contains layers of USe(6) octahedra and MSe(4) (M = Cu, Ag) tetrahedra, separated by Tl(+) cations. The packing of the octahedra and the tetrahedra within the layers is compared to the packing arrangements found in other layered actinide chalcogenides. Tl(3)Cu(4)USe(6) displays peaks in its magnetic susceptibility at 5 and 70 K. It exhibits modified Curie-Weiss paramagnetic behavior with an effective magnetic moment of 1.58(1) µ(B) in the temperature range 72-300 K, whereas Tl(2)Ag(2)USe(4) exhibits modified Curie-Weiss paramagnetic behavior with µ(eff) = 3.4(1) µ(B) in the temperature range 100-300 K. X-ray absorption near-edge structure (XANES) results from scanning transmission X-ray spectromicroscopy confirm that Tl(3)Cu(4)USe(6) has Se bonding characteristic of discrete Se(2-) units, Cu bonding generally representative of Cu(+), and U bonding consistent with a U(4+) or U(5+) species. On the basis of these measurements, as well as bonding arguments, the formal oxidation states for U may be assigned as +5 in Tl(3)Cu(4)USe(6) and +4 in Tl(2)Ag(2)USe(4).