Virtual reality and 3D printing in clinical anesthesia: a case series of two years' experience in a single tertiary medical centre.

PURPOSE: Anatomically correct patient-specific models made from medical imaging can be printed on a three-dimensional (3D) printer or turned into a virtual reality (VR) program. Until recently, use in anesthesia has been limited. In 2019, the anesthesia department at Tel Aviv Medical Center launched a 3D program with the aim of using 3D modelling to assist in preoperative anesthesia planning. METHODS: A retrospective review of all relevant patients between July 2019 and June 2021 referred for preoperative airway planning with 3D modelling. Patient files were reviewed for correlation between the model-based airway plan and the actual airway plan, the type of model used, and any anesthetic complications related to airway management. RESULTS: Twenty patients were referred for 3D modelling. Of these, 15 models were printed, including 12 children requiring one lung ventilation. Five patients had VR reconstructions, including three with mediastinal masses. One patient had both a 3D-printed model and a VR reconstruction. There were two cases (10%) where the model plan did not correlate with the final airway plan and one case where a model could not be created because of poor underlying imaging. For the remaining 17 cases, the plan devised on the model matched the final airway plan. There were no anesthetic complications. CONCLUSIONS: Three-dimensional modelling and subsequent printing or VR reconstruction are feasible in clinical anesthesia. Its routine use for patients with challenging airway anatomy correlated well with the final clinical outcome in most cases. High-quality imaging is essential.

RéSUMé: OBJECTIF: Des modèles anatomiquement corrects spécifiques à un·e patient·e réalisés à partir de l'imagerie médicale peuvent être imprimés sur une imprimante tridimensionnelle (3D) ou transformés en programme de réalité virtuelle (RV). Jusqu'à récemment, l'utilisation de cette modalité était limitée en anesthésie. En 2019, le service d'anesthésie du centre médical de Tel Aviv a lancé un programme 3D dans le but d'utiliser la modélisation 3D pour faciliter la planification préopératoire de l'anesthésie. MéTHODE: Nous avons réalisé un examen rétrospectif de toute la patientèle concernée référée pour une planification préopératoire des voies aériennes avec modélisation 3D entre juillet 2019 et juin 2021. Les dossiers des patient·es ont été examinés pour déterminer la corrélation entre le plan de prise en charge des voies aériennes fondé sur le modèle et le plan fondé sur les voies aériennes réelles, le type de modèle utilisé et toute complication anesthésique liée à la prise en charge des voies aériennes. RéSULTATS: Vingt patient·es ont été référé·es pour la modélisation 3D. À partir de cette cohorte, 15 modèles ont été imprimés, dont 12 pour des enfants nécessitant une ventilation pulmonaire. Cinq patient·es ont bénéficié de reconstructions en RV, dont trois avec des masses médiastinales. Un modèle imprimé en 3D et une reconstruction en RV ont été créés pour une personne. Il y a eu deux cas (10 %) où le plan modèle n'était pas corrélé avec le plan des voies aériennes final et un cas où il n'a pas été possible de créer un modèle en raison d'une mauvaise imagerie sous-jacente. Pour les 17 cas restants, le plan conçu sur le modèle correspondait au plan final de prise en charge des voies aériennes. Il n'y a pas eu de complications anesthésiques. CONCLUSION: La modélisation tridimensionnelle et l'impression ultérieure ou la reconstruction en RV sont réalisables en anesthésie clinique. Leur utilisation systématique pour les patient·es présentant une anatomie difficile au niveau des voies aériennes était bien corrélée avec le résultat clinique final dans la plupart des cas. Une imagerie de haute qualité est essentielle.

Internal Hemipelvectomy for primary bone sarcomas using intraoperative patient specific instruments- the next step in limb salvage concept.

BACKGROUND: During pelvic Sarcoma resections, Surgeons often struggle to obtain negative margins while minimizing collateral damage and maintaining limb function. These complications are usually due to the complex anatomy of the pelvis. Here we present an accurate 3D surgical approach, including pre-operative printing of models and intraoperative patient-specific instruments (PSIs) for optimizing pelvic sarcoma resections. METHODS: This single-center retrospective study (N = 11) presents surgical, functional, and oncological outcomes of patients (average age 14.6 +/- 7.6 years, 4 males) who underwent pelvic sarcoma resections using a 3D surgical approach between 2016 and 2021. All patients were followed up for at least 24 months (mean = 38.9 +/- 30.1 months). RESULTS: Our results show promising surgical, oncological, and functional outcomes. Using a 3D approach, 90.9% had negative margins, and 63.6% did not require reconstruction surgery. The average estimated blood loss was 895.45 ± 540.12 cc, and the average surgery time was 3:38 ± 0.05 hours. Our results revealed no long-term complications. Three patients suffered from short-term complications of superficial wound infections. At 24 month follow up 72.7% of patients displayed no evidence of disease. The average Musculoskeletal Tumor Society (MSTS) score at 12 months was 22.81. CONCLUSION: 3D technology enables improved accuracy in tumor resections, allowing for less invasive procedures and tailored reconstruction surgeries, potentially leading to better outcomes in function and morbidity. We believe that this approach will enhance treatments and ease prognosis for patients diagnosed with pelvic sarcoma and will become the standard of care in the future.

Development and Validation of a Hybrid Bronchoscopy Trainer Using Three-Dimensional Printing.

INTRODUCTION: Simulation is an essential component of medical education. Commercially available intubation simulators often lack anatomical fidelity of the lower airway and are therefore not suitable for teaching bronchoscopy or lung isolation. By using a desktop 3-dimensional (3D) printer, we aimed to create and validate a hybrid simulator from an existing mannequin with a 3D-printed lower airway that has anatomical fidelity and is financially affordable compared with commercially available models. METHODS: Using an anonymized computed tomography scan of an adult male patient, we developed a 3D model of the airway from below the larynx to the 3rd generation bronchi, which was then printed on a desktop 3D printer. The printed airway was attached to an existing mannequin below the larynx via a universal adaptor. Ten anesthesiology attendings performed a blinded comparison of the hybrid mannequin with a commercially available mannequin for tactile and visual fidelity when performing intubation, bronchoscopy, and lung isolation. They were also asked to assess the models for educational suitability. RESULTS: The 3D printed model was judged more suitable for teaching double-lumen tube insertion to novice physicians compared with the commercial model, with median (interquartile range) scores of 5 (4-5) versus 3 (2-4), P = 0.017. Similar results were found for bronchial blocker insertion and bronchoscopy. The visual fidelity of the bronchial anatomy was scored as 5 (4-5) and 2 (1-3) for the 3D-printed and the commercial models, respectively (P = 0.007). CONCLUSION: By creating a hybrid model combining an existing commercially available mannequin with a 3D-printed trachea and bronchial tree, we have created an affordable training simulator suitable for teaching lung isolation and bronchoscopy. Enhancing existing mannequins with 3D-printed parts may be of particular interest to institutions that do not have the funds to buy models with anatomical fidelity but do have access to a 3D printer.

Intercalary and geographic lower limb tumor resections with the use of 3D printed Patient Specific Instruments- when less is more.

Background: Primary bone sarcomas are associated with critically sized bone defects and require complete resection with negative margins. Recent advancements in health care have pioneered novel approaches such as the implementation of 3D surgical technologies. This study presents oncological and functional outcomes following tumor resections of long bones with the use of customized 3D-printed Patient Specific Instruments (PSIs). Methods: This single-center retrospective study is comprised of seventeen patients who underwent either intercalary (N = 12) or geographic (N = 5) resections with various reconstruction methods including allograft (N = 8), vascularized fibula (Capanna) (N = 7), and 3D printed customized titanium implants (N = 2), between the years 2016-2020. All patients were operated on with a 3D surgical workflow, including intraoperative PSIs, and were followed up postoperatively for at least 12 months (average 31.40 ± 12.13 months) to assess oncological and functional outcomes. Results: All patients demonstrated negative surgical margins, apart from one patient who had planned positive margins. Three patients suffered from short-term complications, and three patients underwent revision surgery due to graft non-union or pathological fracture. One patient suffered from local recurrence and underwent above-knee amputation. Three patients suffered from lung metastasis. MSTS at 12-month follow-up was 26.9.±5.87. Conclusion: Customized 3D-printed osteotomy PSIs provide surgeons with a novel tool for optimizing bone resection and reconstruction in long bones surgeries, thus minimizing overall tissue trauma and reducing the risk of damage to nervous and vascular structures. This study demonstrates that the use of PSIs has the potential to improve functional and oncological outcomes. We believe that this technique will become increasingly popular in the future as a widely applicable, highly accurate, cost-effective optimization tool.

In-hospital production of 3D-printed casts for non-displaced wrist and hand fractures.

OBJECTIVES: To examine the clinical feasibility and results of a multidisciplinary workflow, employing rapid three-dimensional (3D) scanning and modeling software along with a high-speed printer, for in-hospital production of patient-specific 3D-printed casts, for the treatment of non-displaced wrist and hand fractures. METHODS: Consenting adult patients admitted to the emergency department (ED) due to wrist or hand fractures between January and February 2021 were prospectively enrolled. The study participants underwent conversion of the standard plaster of Paris cast to a 3D-printed cast one week after the ED visit, and follow-up examinations were performed around two, six, and twelve weeks later. The primary objective was to examine the clinical feasibility in terms of complexity and length of the overall procedure. Secondary outcomes were patient-reported impressions and radiological results. RESULTS: Twenty patients (16 males, mean age 37 ± 13.1 years) were included. The entire printing workflow took a mean of 161 ± 8 min. All patients demonstrated clinical improvement and fracture union at final follow-up, with no pressure sores or loss of reduction. Patient-reported comfort and satisfaction rates were excellent. The mean Visual Analog Scale was 0.9 ± 1.1 and 0.6 ± 1, and the mean Disabilities of the Arm, Shoulder, and Hand score was 18.7 ± 9.5 and 7.6 ± 7.6 at 2 and 6 weeks after application of the 3D-printed cast, respectively. CONCLUSION: The in-hospital workflow was feasible and efficient, with excellent clinical and radiographic results and high patient satisfaction and comfort rates. Our medical center now routinely provides this cast option for non-displaced wrist and hand fractures. LEVEL OF EVIDENCE: IV, Therapeutic Study.

In situ cryoablation of sacral Giant Cell Tumor using three-dimensional (3D) model: A case report.

Three-dimensional planning of in-situ (trans-sacral) image guided cryoablation provides a method to treat sacral GCTs that accommodates the intricacies of the pelvis offering a safer, more efficacious alternative. Here we report on IM a 23-year-old female with a sacral GCT. She presented to Tel Aviv Medical Center with ongoing pain as well as neurological symptoms. For six years, the patient was in-and-out of the hospital for Denosumab treatment and recurrent infections. Eventually, further treatment became necessary, and she was treated with image guided cryoablation. By six months follow-up, the patient was mobile and pain-free.

3D-printed Cutting Guides for Lower Limb Deformity Correction in the Young Population.

BACKGROUND: Three-dimensional (3D) virtual surgical planning technology has advanced applications in the correction of deformities of long bones by enabling the production of 3D stereolithographic models, patient-specific instruments and surgical-guiding templates. Herein, we describe the implementation of this technology in young patients who required a corrective osteotomy for a complex 3-plane (oblique plane) lower-limb deformity. PATIENTS AND METHODS: A total of 17 patients (9 males, average age 14.7 y) participated in this retrospective study. As part of preoperative planning, the patients' computerized tomographic images were imported into a post-processing software, and virtual 3D models were created by a segmentation process. Femoral and tibial models and cutting guides with locking points were designed according to the deformity correction plan. They were used for both planning and as intraoperative guides. Clinical parameters, such as blood loss and operative time were compared with a traditional surgical approach group. RESULTS: All osteotomies in the 3D group were executed with the use intraoperative customized cutting guides which matched the preoperative planning simulation and allowed easy fixation with prechosen plates. Surgical time was 101±6.2 minutes for the 3D group and 126.4±16.1 minutes for the control group. The respective intraoperative hemoglobin blood loss was 2.1±0.2 and 2.5+0.3 g/dL.Clinical and radiographic follow-up findings showed highly satisfactory alignment of the treated extremities in all 3D intervention cases, with an average time-to-bone union (excluding 2 neurofibromatosis 1 patients) of 10.3 weeks (range 6 to 20 wk). CONCLUSION: The use of 3D-printed models and patient-specific cutting guides with locking points improves the clinical outcomes of osteotomies in young patients with complex bone deformities of the lower limbs. LEVEL OF EVIDENCE: Level III.

Three dimensional printed models of the airway for preoperative planning of open Laryngotracheal surgery in children: Surgeon's perception of utility.

BACKGROUND: Preoperative planning of open laryngotracheal surgery is important for achieving good results. This study examines the surgeon's perception of the importance of using life size 3D printed models of the pediatric airway on surgical decision making. METHODS: Life-size three-dimensional models of the upper airway were created based on CT images of children scheduled for laryngotracheal-reconstruction and cricotracheal resection with anastomosis. Five pediatric airway surgeons evaluated the three-dimensional models for determining the surgical approach, incision location and length, graft length, and need for single or double-stage surgery of seven children (median age 4.4 years, M:F ratio 4:3). They rated the importance of the three-dimensional model findings compared to the direct laryngoscopy videos and CT findings for each domain on a validated Likert scale of 1-5. RESULTS: The mean rating for all domains was 3.6 ± 0.63 ("moderately important" to "very important"), and the median rating was 4 ("very important"). There was full agreement between raters for length of incision and length of graft. The between-rater agreement was 0.608 ("good") for surgical approach, 0.585 ("moderate") for incision location, and 0.429 ("moderate") for need for single- or two-stage surgery. CONCLUSION: Patient-specific three-dimensional printed models of children's upper airways were scored by pediatric airway surgeons as being moderately to very important for preoperative planning of open laryngotracheal surgery. Large-scale, objective outcome studies are warranted to establish the reliability and efficiency of these models.

Amelioration of experimental colitis by Copaxone is associated with class-II-restricted CD4 immune blocking.

UNLABELLED: Copaxone modifies TH1 immune response in multiple sclerosis. As Crohn's disease shares TH1 predominance, this study came to investigate the anti-inflammatory response of Copaxone in animal model of colitis. METHODS: Colitis was induced by intra-rectal instillation of TNBS in 2 animal groups; one of them was daily treated intraperitoneally by 300 mug Copaxone starting 48 h post-colitis induction. Both colitis groups were compared to naive group. Eight male C57Bl6 mice were used in each group. At day 12, distal colon was excised for standard scoring, splenocytes were isolated for FACS and serum cytokines were assessed. Splenocytes were in-vitro-stimulated with colitis protein extracts in the presence or absence of Copaxone. Lymphocytes were blocked by either MHC anti-class I or anti-class II antibodies prior to Copaxone administration. RESULTS: Copaxone markedly alleviated macro/microscopic colitis scoring as they decreased from 2.9 +/- 1.1/2.6 +/- 0.8 in colitis group to 1.7 +/- 1/1.5 +/- 0.5 in Copaxone-treated mice (P = 0.03/P = 0.008, respectively) compared to 0 +/- 0/1 +/- 0 in naives (P < 0.001/P < 0.01, respectively). CD4 subsets significantly decreased following Copaxone administration as compared to naive mice (P = 0.05). Although Copaxone-treated mice manifested a block of both serum TH1/TH2 responses, only interferon gamma secreting CD4 cells significantly decreased. NK cells tend to increase following colitis induction (P = 0.08), however, they significantly decreased in Copaxone-treated animals (P = 0.006). NK-T followed NK pattern. Using in vitro studies, Copaxone showed amelioration of T-cell proliferation that was significantly blocked when cells were pre-incubated with anti-MHC class II but not class I antibodies. CONCLUSIONS: Copaxone had class-II-restricted anti-inflammatory effect in our animal colitis model associated with CD4/NK/NKT/TH1/TH2 suppression.