RESUMO
Calotropis procera cysteine peptidases (CpCPs) have presented several potential biotechnological applications. Here, these enzymes were immobilized on glyoxyl-agarose (glyoxyl-CpCPs) with yields of 90-95 % and the recovered activities ranged from 10 % to 15 %, according to enzyme loadings (5, 10, 20, 40, and 50 mgBSAeq/g). Spectrophotometric assays and SDS-PAGE showed that the casein hydrolysis by glyoxyl-CpCPs was similar to soluble CpCPs. In addition, glyoxyl-CpCPs exhibited similar ratio of milk-clotting activity to proteolytic activity in comparison with soluble CpCPs and chymosin. Even after being stored for six months at 8 °C, the residual proteolytic activity of glyoxyl-CpCPs remained close to 100 %. Atomic force microscopy and dynamic light scattering techniques showed that the process of casein micelle aggregation after treatment with glyoxyl-CpCPs was very similar to its soluble form and chymosin. Glyoxyl-CpCPs performed well after five reaction cycles, producing cheeses with yield, moisture, protein, and fat similar to those produced with chymosin.
Assuntos
Calotropis , Cisteína Proteases , Sefarose , Quimosina , Cisteína , Caseínas , Cisteína Proteases/metabolismo , Concentração de Íons de Hidrogênio , Enzimas Imobilizadas/metabolismoRESUMO
Lipase from Thermomyces lanuginosus (TLL) has been covalently immobilized on heterofunctional octyl-vinyl agarose. That way, the covalently immobilized enzymes will have identical orientation. Then, it has blocked using hexyl amine (HEX), ethylenediamine (EDA), Gly and Asp. The initial activity/stability of the different biocatalysts was very different, being the most stable the biocatalyst blocked with Gly. These biocatalysts had been utilized to analyze if the enzyme activity could decrease differently along thermal inactivation courses depending on the utilized substrate (that is, if the enzyme specificity was altered during its inactivation using 4 different substrates to determine the activity), and if this can be altered by the nature of the blocking agent and the inactivation conditions (we use pH 5, 7 and 9). Results show great changes in the enzyme specificity during inactivation (e.g., activity versus triacetin was much more quickly lost than versus the other substrates), and how this was modulated by the immobilization protocol and inactivation conditions. The difference in the changes induced by immobilization and inactivation were confirmed by fluorescence studies. That is, the functional and structural analysis of partially inactivated immobilized enzyme showed that their inactivation pathway is strongly depended on the support features and inactivation conditions.
Assuntos
Enzimas Imobilizadas/química , Eurotiales/enzimologia , Proteínas Fúngicas/química , Lipase/química , Microesferas , Sefarose/análogos & derivados , Ácido Aspártico/química , Enzimas Imobilizadas/metabolismo , Etilenodiaminas/química , Proteínas Fúngicas/metabolismo , Glicina/química , Lipase/metabolismo , Especificidade por Substrato , Sulfonas/química , Triacetina/químicaRESUMO
This study reports an alternative strategy for the expression of a recombinant L-AI from Enterococcus faecium DBFIQ E36 by auto-induction using glucose and glycerol as carbon sources and residual whey lactose as inducer agent. Commercial lactose and isopropyl ß-D-1-thiogalactopyranoside (IPTG) were also evaluated as inducers for comparison of enzyme expression levels. The enzymatic extracts were purified by affinity chromatography, characterized, and applied in the bioconversion of D-galactose into D-tagatose. L-AI presented a catalytic activity of 1.67 ± 0.14, 1.52 ± 0.01, and 0.7 ± 0.04 U/mL, when expressed using commercial lactose, lactose from whey, and IPTG, respectively. Higher activities could be obtained by changing the protocol of enzyme extraction and, for instance, the enzymatic extract produced with whey presented a catalytic activity of 3.8 U/mL. The specific activity of the enzyme extracts produced using lactose (commercial or residual whey) after enzyme purification was also higher when compared to the enzyme expressed with IPTG. Best results were achieved when enzyme expression was conducted using 4 g/L of residual whey lactose for 11 h. These results proved the efficacy of an alternative and economic protocol for the effective expression of a recombinant L-AI aiming its high-scale production.
Assuntos
Aldose-Cetose Isomerases/genética , Aldose-Cetose Isomerases/metabolismo , Enterococcus faecium/enzimologia , Escherichia coli/crescimento & desenvolvimento , Isopropiltiogalactosídeo/metabolismo , Lactose/metabolismo , Aldose-Cetose Isomerases/isolamento & purificação , Proteínas de Bactérias/genética , Proteínas de Bactérias/metabolismo , Clonagem Molecular , Meios de Cultura/química , Enterococcus faecium/genética , Escherichia coli/genética , Escherichia coli/metabolismo , Regulação Bacteriana da Expressão Gênica , Regulação Enzimológica da Expressão Gênica , Glucose/metabolismo , Glicerol/metabolismo , Concentração de Íons de Hidrogênio , Proteínas Recombinantes/metabolismo , Soro do Leite/químicaRESUMO
The potential use of alternative culture media towards the development of a sustainable bioprocess to produce lipases by Diutina rugosa is clearly demonstrated. First, a synthetic medium containing glucose, peptone, yeast extract, oleic acid, and ammonium sulfate was proposed, with lipase activity of 143 U/L. Then, alternative culture media formulated with agro-industrial residues, such as molasses, corn steep liquor (CSL), and olive mill waste (OMW), were investigated. An experimental design was conducted, and only CSL concentration was found to have a positive effect in lipase production. The highest lipase activity (561 U/L) was produced on a mixture of molasses (5 g/L), CSL (6 g/L), OMW (0.5% v/v), 0.5 g/L of ammonium sulfate, and 3 g/L of peptone at 24 h of cultivation. Lipase production was also carried out in a 1-L bioreactor leading to a slightly higher lipase activity at 24 h of cultivation. The semi-purified enzyme exhibits an optimum temperature and pH of 40 °C and 7.0, respectively. Finally, the media cost per unit of lipase produced (UPC) was influenced by the medium components, specially by the inducer used. The lowest UPC was obtained when the agro-industrial residues were combined and used at the improved concentrations.
Assuntos
Reatores Biológicos , Proteínas Fúngicas/biossíntese , Microbiologia Industrial , Lipase/biossíntese , Saccharomycetales/enzimologia , Eliminação de Resíduos Líquidos , Meios de CulturaRESUMO
In this study, the modulation of enzymatic biocatalysts were developed by the use of lipase B from Candida antarctica covalently immobilized on an eco-friendly support, cashew apple bagasse, activated with 10% glycidol-ethylenediamine-glutaraldehyde (GEG) under different immobilization strategies (5 mM or 100 mM ionic strength and in absence or presence of 0.5% (v/v) Triton X-100). The biocatalysts were characterized for thermal and organic solvents stabilities and compared with the soluble enzyme. The biocatalysts were then applied to the hydrolysis of the rac-indanyl acetate (2:1 ratio enzyme/substrate) at pH 7.0 and 30 °C for 24 h. For all the strategies evaluated, GEG promoted kinetic resolution of rac-indanyl acetate with maximum conversion (50%) and led to (R)-indanol with excellent enantiomeric excess (97%), maintaining the maximum conversion for five consecutive cycles of hydrolysis. Therefore, the use of cashew apple bagasse has proved to be a promising eco-friendly support for enzyme immobilization, since it resulted in stable biocatalysts for enzymatic kinetic resolution.
Assuntos
Acetatos/química , Basidiomycota/enzimologia , Proteínas Fúngicas/química , Lipase/química , Anacardium/metabolismo , Candida/enzimologia , Estabilidade Enzimática , Enzimas Imobilizadas/química , Etilenodiaminas/química , Glutaral/química , Concentração de Íons de Hidrogênio , Cinética , Bases de Schiff , Solventes/química , Estereoisomerismo , Temperatura , Fatores de TempoRESUMO
Lipase from Thermomyces lanuginosus (TLL) was immobilized onto a novel heterofunctional support, divinyl sulfone (DVS) superparamagnetic nanoparticles (SPMNs) functionalized with polyethyleneimine (PEI). Particle size and zeta potential measurements, elemental analysis, X-ray powder diffraction, magnetic measurements, and infrared spectroscopy analysis were used to characterize the TLL preparations. At pH 10, it was possible to achieve 100 % of immobilization yield in 1â¯h. The immobilization pH gives TLL preparations with different stabilities; indeed the TLL preparation immobilized at pH 5.0 was the most stable during the thermal inactivation at all pH values. For the hydrolysis of racemic methyl mandelate, the nanobiocatalysts immobilized at pH 5.0 and blocked with ethylenediamine (EDA) and ethanolamine (ETA) obtained good enantioselectivities (68 % and 72 %, respectively) with high catalytic activities in the reaction medium at pH 7.0. The operational stability of the systems was evaluated in the esterification reaction of benzyl alcohol, obtaining up to 61 % conversion after the seventh reaction cycle. These results show that SPMN@PEI-DVS support is a robust strategy for the easy and rapid recovery of the nanobiocatalyst by applying a magnetic field, showing great potential for industrial applications.
Assuntos
Enzimas Imobilizadas/química , Eurotiales/enzimologia , Lipase/química , Nanopartículas Magnéticas de Óxido de Ferro/química , Polietilenoimina/química , Sulfonas/química , Compostos de Benzil/metabolismo , Estabilidade Enzimática , Enzimas Imobilizadas/metabolismo , Esterificação , Etanolamina/química , Etilenodiaminas/química , Proteínas Fúngicas/química , Proteínas Fúngicas/metabolismo , Concentração de Íons de Hidrogênio , Hidrólise , Lipase/metabolismo , Temperatura , Fatores de TempoRESUMO
A functional screening of 1152 clones from a plasmid library constructed with DNA extracted from Brazilian mangrove sediments revealed 3 positive clones for ester-hydrolyzing enzymes, or about one lipolytic gene per 1.2 Mb DNA, which corroborates the idea that oil-contaminated mangroves are a good source of novel microbial lipases/esterases. The partial sequence of the clone LipG7 (1179 bp) showed 30.2% of predicted structure identity with a known esterase, confirming LipG7 as a new member of family VIII esterases. LigG7 shared 80% sequence identity with 1,4-butanediol diacrylate esterase from the Gammaprotebacteria Porticoccus hydrocarbonoclasticus, suggesting it belongs to the Porticoccaceae family. LipG7 was heterologously expressed in Escherichia coli Rosetta-Gami DE3; the purified recombinant enzyme exhibited a predicted molecular weight of 45.2 kDa and exceptional activity towards 4-nitrophenyl butyrate, compared with other recombinant esterases, highlighting its enormous potential for biological applications.
Assuntos
Carboxilesterase/genética , Carboxilesterase/isolamento & purificação , Gammaproteobacteria/genética , Sequência de Aminoácidos/genética , Bactérias/genética , Bactérias/metabolismo , Sequência de Bases/genética , Brasil , Butiratos/metabolismo , Carboxilesterase/metabolismo , Esterases/metabolismo , Gammaproteobacteria/metabolismo , Expressão Gênica/genética , Biblioteca Gênica , Metagenoma/genética , Filogenia , Plasmídeos/genética , Alinhamento de Sequência/métodos , Análise de Sequência de DNA/métodos , Especificidade por Substrato/genética , Áreas AlagadasRESUMO
Co-immobilization is a groundbreaking technique for enzymatic catalysis, sometimes strategic, as for dextransucrase and dextranase. In this approach, dextranase hydrolytic action removes the dextran layer that covers dextransucrase reactive groups, improving the immobilization. Another advantage is the synergic effect of the two enzymes towards prebiotic oligosaccharides production. Thus, both enzymes were co-immobilized onto the heterobifunctional support Amino-Epoxy-Glyoxyl-Agarose (AMEG) and the ion exchanger support monoaminoethyl-N-ethyl-agarose (Manae) at pH 5.2 and 10, followed or not by glutaraldehyde treatment. This work is the first attempt to immobilize dextransucrase under alkaline conditions. The immobilized dextransucrase on AMEG support at pH 10 (12.78 ± 0.70 U/g) presents a similar activity of the biocatalyst produced at pH 5.2 (14.95 ± 0.82 U/g). The activity of dextranase immobilized onto Manae was 5-fold higher than the obtained onto AMEG support. However, the operational stability test showed that the biocatalyst produced on AMEG at pH 5.2 kept >60% of both enzyme activities for five batches. The glutaraldehyde treatment was not worthwhile to improve the operational stability of this biocatalyst.
Assuntos
Dextranase/química , Enzimas Imobilizadas/química , Glucosiltransferases/química , Sefarose/química , Catálise , Estabilidade Enzimática , Glutaral/química , Concentração de Íons de Hidrogênio , TemperaturaRESUMO
The synthesis of ethyl butyrate catalyzed by lipases A (CALA) or B (CALB) from Candida antarctica immobilized onto magnetic nanoparticles (MNP), CALA-MNP and CALB-MNP, respectively, is hereby reported. MNPs were prepared by co-precipitation, functionalized with 3-aminopropyltriethoxysilane, activated with glutaraldehyde, and then used as support to immobilize either CALA or CALB (immobilization yield: 100 ± 1.2% and 57.6 ± 3.8%; biocatalysts activities: 198.3 ± 2.7 Up-NPB/g and 52.9 ± 1.7 Up-NPB/g for CALA-MNP and CALB-MNP, respectively). X-ray diffraction and Raman spectroscopy analysis indicated the production of a magnetic nanomaterial with a diameter of 13.0 nm, whereas Fourier-transform infrared spectroscopy indicated functionalization, activation and enzyme immobilization. To determine the optimum conditions for the synthesis, a four-variable Central Composite Design (CCD) (biocatalyst content, molar ratio, temperature and time) was performed. Under optimized conditions (1:1, 45 °C and 6 h), it was possible to achieve 99.2 ± 0.3% of conversion for CALA-MNP (10 mg) and 97.5 ± 0.8% for CALB-MNP (12.5 mg), which retained approximately 80% of their activity after 10 consecutive cycles of esterification. Under ultrasonic irradiation, similar conversions were achieved but at 4 h of incubation, demonstrating the efficiency of ultrasound technology in the enzymatic synthesis of esters.
Assuntos
Butiratos/metabolismo , Candida/metabolismo , Enzimas Imobilizadas/química , Enzimas Imobilizadas/metabolismo , Proteínas Fúngicas/metabolismo , Lipase/metabolismo , Nanopartículas de Magnetita/química , Biocatálise , Esterificação/fisiologia , Glutaral/metabolismo , Ondas UltrassônicasRESUMO
In this communication, lipase A from Candida antarctica (CALA) was immobilized by covalent bonding on magnetic nanoparticles coated with chitosan and activated with glutaraldehyde, labelled CALA-MNP, (immobilization parameters: 84.1% ± 1.0 for immobilization yield and 208.0 ± 3.0 U/g ± 1.1 for derivative activity). CALA-MNP biocatalyst was characterized by X-ray Powder Diffraction (XRPD), Fourier Transform Infrared (FTIR) spectroscopy, Thermogravimetry (TG) and Scanning Electron Microscope (SEM), proving the incorporation of magnetite and the immobilization of CALA in the chitosan matrix. Besides, the immobilized biocatalyst showed a half-life 8-11 times higher than that of the soluble enzyme at pH 5-9. CALA showed the highest activity at pH 7, while CALA-MNP presented the highest activity at pH 10. The immobilized enzyme was more active than the free enzyme at all studied pH values, except pH 7.
Assuntos
Candida/enzimologia , Quitosana/química , Lipase/metabolismo , Nanopartículas de Magnetita/química , Estabilidade Enzimática , Enzimas Imobilizadas/metabolismo , Proteínas Fúngicas/metabolismoRESUMO
The lipase from Pseudomonas fluorescens (PFL) has been immobilized on glyoxyl-octyl agarose and compared to the enzyme immobilized on octyl-agarose. Thus, PFL was immobilized at pHâ¯7 on glyoxyl-octyl support via lipase interfacial activation and later incubated at pHâ¯10.5 for 20â¯h before reduction to get some enzyme-support covalent bonds. This permitted for 70% of the enzyme molecules to become covalently attached to the support. This biocatalyst was slightly more stable than the octyl-PFL at pHâ¯5, 7 and 9, or in the presence of some organic solvents (stabilization factor no higher than 2). The presence of phosphate anions produced enzyme destabilization, partially prevented by the immobilization on glyoxyl-octyl (stabilization factor became 4). In contrast, the presence of calcium cations promoted a great PFLstabilization, higher in the case of the glyoxyl-octyl preparation (that remained 100% active when the octyl-PFL preparations had lost 20% of the activity). However, it is in the operational stability where the new biocatalyst showed the advantages: in the hydrolysis of 1â¯M triacetin in 60% 1.4 dioxane, the octyl biocatalyst released >60% of the enzyme in the first cycle, while the covalently attached enzyme retained its full activity after 5 reaction cycles.
Assuntos
Proteínas de Bactérias/química , Enzimas Imobilizadas/química , Glioxilatos/química , Lipase/química , Pseudomonas fluorescens/enzimologia , Sefarose/química , Estabilidade Enzimática , Concentração de Íons de HidrogênioRESUMO
A novel heterofunctional support for enzyme immobilization, chitosan-divinyl sulfone, was assessed in this study. The activation of chitosan with DVS was carried out at three different pHs (10.0, 12.5 and 14.0) and a Candida antarctica Lipase B (CALB) was selected as the model enzyme. After immobilization, the biocatalysts were incubated under alkaline conditions in a buffer to facilitate the multipoint covalent attachment, followed by incubation in ethylenediamine (EDA) aiming at blocking the remaining reactive groups. The highest thermal stability was obtained when pHâ¯10.0 was used during support activation. These results were shown to be better than those obtained when using glutaraldehyde as the support-activating reagent. Subsequently, the immobilization pH was investigated (5.0, 7.0 and 10.0) prior to alkaline incubation, with the highest enzyme stability levels found at pHâ¯10.0. Finally, the selected biocatalyst was used in the hydrolysis of ethyl hexanoate and presented an activity of 14,520.37â¯U/g of immobilized lipase at pHâ¯5.0. These results show that chitosan activated with divinyl sulfone is a very promising support for enzyme immobilization and the proposed protocol is able to successfully improve enzyme stability.
Assuntos
Quitosana/química , Enzimas Imobilizadas , Proteínas Fúngicas , Lipase , Sulfonas/química , Ativação Enzimática , Estabilidade Enzimática , Enzimas Imobilizadas/química , Análise de Elementos Finitos , Proteínas Fúngicas/química , Concentração de Íons de Hidrogênio , Hidrólise , Lipase/química , Estrutura Molecular , Nanopartículas/química , Nanopartículas/ultraestrutura , Ligação Proteica , Análise Espectral , TermogravimetriaRESUMO
In this work, the synthesis of two fruit flavor esters, namely methyl and ethyl butyrate, by lipase from Rhizomucor miehei immobilized onto chitosan in the presence of the surfactant sodium dodecyl sulfate SDS was investigated. In the optimized conditions, maximum esterification yield for ethyl butyrate and methyl butyrate was (92 ± 1%) and (89 ± 1%), respectively. Esterification yields for both reactions were comparable or even superior to the ones achieved when the synthesis was catalyzed by a commercial enzyme, Lipozyme®, at the same reaction conditions. For ethyl butyrate, the developed biocatalyst was used for seven consecutive cycles of reaction with retention of its catalytic activity. For methyl butyrate synthesis the biocatalyst was used for four consecutive cycles without loss of its catalytic activity. The results show that chitosan may be employed in obtaining biocatalysts with high catalytic efficiency and can successfully replace the currently commercial available biocatalysts.
Assuntos
Butiratos/química , Rhizomucor/metabolismo , Quitosana , Enzimas Imobilizadas , Esterificação , Ésteres/síntese química , Aromatizantes/síntese química , Proteínas Fúngicas , Cinética , Lipase/metabolismo , Lipase/farmacologia , Dodecilsulfato de Sódio/química , TensoativosRESUMO
A recombinant L-arabinose isomerase from Enterococcus faecium DBFIQ E36 was immobilized onto multifunctional epoxide supports by chemical adsorption and onto a chelate-activated support via polyhistidine-tag, located on the N-terminal (N-His-L-AI) or on the C-terminal (C-His-L-AI) sequence, followed by covalent bonding between the enzyme and the support. The results were compared to reversible L-AI immobilization by adsorption onto charged agarose supports with improved stability. All the derivatives presented immobilization yields of above 75%. The ionic interaction established between agarose gels containing monoaminoethyl-N-aminoethyl structures (MANAE) and the enzyme was the most suitable strategy for L-AI immobilization in comparison to the chelate-activated agarose. In addition, the immobilized biocatalysts by ionic interaction in MANAE showed to be the most stable, retaining up to 100% of enzyme activity for 60 min at 60 °C and with Km values of 28 and 218 mM for MANAE-N-His-L-AI and MANAE-C-His-L-AI, respectively.
Assuntos
Aldose-Cetose Isomerases/metabolismo , Proteínas de Bactérias/metabolismo , Enterococcus faecium/enzimologia , Hexoses/biossíntese , Aldose-Cetose Isomerases/genética , Proteínas de Bactérias/genética , Biocatálise , Biotecnologia , Enterococcus faecium/genética , Estabilidade Enzimática , Enzimas Imobilizadas/genética , Enzimas Imobilizadas/metabolismo , Temperatura Alta , Concentração de Íons de Hidrogênio , Cinética , Proteínas Recombinantes/genética , Proteínas Recombinantes/metabolismo , SolubilidadeRESUMO
Novozyme 435, which is a commercial immobilized lipase B from Candida antarctica (CALB), has been proven to be inadequate for the kinetic resolution of rac-indanyl acetate. As it has been previously described that different immobilization protocols may greatly alter lipase features, in this work, CALB was covalently immobilized on epoxy Immobead-350 (IB-350) and on glyoxyl-agarose to ascertain if better kinetic resolution would result. Afterwards, all CALB biocatalysts were utilized in the hydrolytic resolution of rac-indanyl acetate and rac-(chloromethyl)-2-(o-methoxyphenoxy) ethyl acetate. After optimization of the immobilization protocol on IB-350, its loading capacity was 150 mg protein/g dried support. Furthermore, the CALB-IB-350 thermal and solvent stabilities were higher than that of the soluble enzyme (e.g., by a 14-fold factor at pH 5-70°C and by a 11-fold factor in dioxane 30%-65°C) and that of the glyoxyl-agarose-CALB (e.g., by a 12-fold factor at pH 10-50°C and by a 21-fold factor in dioxane 30%-65°C). The CALB-IB-350 preparation (with 98% immobilization yield and activity versus p-nitrophenyl butyrate of 6.26 ± 0.2 U/g) was used in the hydrolysis of rac-indanyl acetate using a biocatalyst/substrate ratio of 2:1 and a pH value of 7.0 at 30°C for 24 h. The conversion obtained was 48% and the enantiomeric excess of the product (e.e.p ) was 97%. These values were much higher than the ones obtained with Novozyme 435, 13% and 26% of conversion and e.e.p, respectively. © 2018 American Institute of Chemical Engineers Biotechnol. Prog., 34:878-889, 2018.
Assuntos
Candida/enzimologia , Enzimas Imobilizadas/metabolismo , Proteínas Fúngicas/metabolismo , Lipase/metabolismo , Catálise , Concentração de Íons de Hidrogênio , CinéticaRESUMO
Lipase from Rhizomucor miehei (RML) was immobilized onto chitosan support in the presence of some surfactants added at low levels using two different strategies. In the first approach, the enzyme was immobilized in the presence of surfactants on chitosan supports previously functionalized with glutaraldehyde. In the second one, after prior enzyme adsorption on chitosan beads in the presence of surfactants, the complex chitosan beads-enzyme was then cross-linked with glutaraldehyde. The effects of surfactant concentrations on the activities of free and immobilized RML were evaluated. Hexadecyltrimethylammonium bromide (CTAB) promoted an inhibition of enzyme activity while the nonionic surfactant Triton X-100 caused a slight increase in the catalytic activity of the free enzyme and the derivatives produced in both methods of immobilization. The best derivatives were achieved when the lipase was firstly adsorbed on chitosan beads at 4 °C for 1 h, 220 rpm followed by cross-link the complex chitosan beads-enzyme with glutaraldehyde 0.6% v.v-1 at pH 7. The derivatives obtained under these conditions showed high catalytic activity and excellent thermal stability at 60° and 37 °C. The best derivative was also evaluated in the synthesis of two flavor esters namely methyl and ethyl butyrate. At non-optimized conditions, the maximum conversion yield for methyl butyrate was 89%, and for ethyl butyrate, the esterification yield was 92%. The results for both esterifications were similar to those obtained when the commercial enzyme Lipozyme® and free enzyme were used in the same reaction conditions and higher than the one achieved in the absence of the selected surfactant.
Assuntos
Quitosana/sangue , Enzimas Imobilizadas/química , Proteínas Fúngicas/química , Lipase/química , Rhizomucor/enzimologia , Tensoativos/química , Estabilidade Enzimática , Concentração de Íons de HidrogênioRESUMO
l-Arabinose isomerase (EC 5.3.1.4) (l-AI) from Enterococcus faecium DBFIQ E36 was overproduced in Escherichia coli by designing a codon-optimized synthetic araA gene. Using this optimized gene, two N- and C-terminal His-tagged-l-AI proteins were produced. The cloning of the two chimeric genes into regulated expression vectors resulted in the production of high amounts of recombinant N-His-l-AI and C-His-l-AI in soluble and active forms. Both His-tagged enzymes were purified in a single step through metal-affinity chromatography and showed different kinetic and structural characteristics. Analytical ultracentrifugation revealed that C-His-l-AI was preferentially hexameric in solution, whereas N-His-l-AI was mainly monomeric. The specific activity of the N-His-l-AI at acidic pH was higher than that of C-His-l-AI and showed a maximum bioconversion yield of 26% at 50 °C for d-tagatose biosynthesis, with Km and Vmax parameters of 252 mM and 0.092 U mg-1, respectively. However, C-His-l-AI was more active and stable at alkaline pH than N-His-l-AI. N-His-l-AI follows a Michaelis-Menten kinetic, whereas C-His-l-AI fitted to a sigmoidal saturation curve.
Assuntos
Aldose-Cetose Isomerases/genética , Aldose-Cetose Isomerases/metabolismo , Enterococcus faecium/enzimologia , Enterococcus faecium/genética , Hexoses/biossíntese , Aldose-Cetose Isomerases/isolamento & purificação , Cromatografia de Afinidade , Ativação Enzimática , Escherichia coli/genética , Escherichia coli/metabolismo , Engenharia Genética , Proteínas Recombinantes , UltracentrifugaçãoRESUMO
In this study, the biosurfactant production by an Aureobasidium thailandense LB01 was reported for the first time. Different agro-industrial by-products (corn steep liquor, sugarcane molasses, and olive oil mill wastewater) were evaluated as alternative low-cost substrates. The composition of the culture medium was optimized through response surface methodology. The highest biosurfactant production (139±16mg/L) was achieved using a culture medium containing yeast extract (2g/L); olive oil mill wastewater (1.5%, w/w); glucose (6g/L) and KH2PO4 (1g/L) after 48h of fermentation. The partially purified biosurfactant exhibited a critical micelle concentration of 550mg/L, reducing the surface tension of water up to 31.2mN/m. Its molecular structure was found to be similar to a lauric acid ester. The biosurfactant exhibited a better performance than the chemical surfactant sodium dodecyl sulfate (SDS) in oil dispersion assays, thus suggesting its potential application in bioremediation.
Assuntos
Ascomicetos/metabolismo , Azeite de Oliva/metabolismo , Tensoativos/metabolismo , Ascomicetos/crescimento & desenvolvimento , Biodegradação Ambiental , Meios de Cultura/química , Fermentação , Dodecilsulfato de Sódio/química , Tensão Superficial , Tensoativos/química , Tensoativos/isolamento & purificação , Águas Residuárias , ÁguaRESUMO
The objective of this new paper was to evaluate the enzymatic esterification reaction conducted in supercritical or near-critical CO2, catalyzed by immobilized lipase B from Candida antarctica (CALB). The biocatalyst was prepared through the immobilization of CALB by covalent attachment using chitosan sequentially activated with Glycidol, ethylenediamine (EDA) and glutaraldehyde as support. In order to determine the best operational conditions of the esterification reaction (1: 1 (alcohol-acid); biocatalyst content, 10% (by substrate mass); 45 °C), an experimental design (23) was conducted to evaluate the effects of the following parameters: alcohol to oil molar ratios, reaction time and temperature. The maximum loading of chitosan was 20 mg protein/g support, and the thermal and solvent stability of the new biocatalyst was higher than that of the CALB-GX (by a 26-fold factor), CALB-OC (by a 53-fold factor) and Novozym 435 (by a 3-fold factor). The maximum conversion was 46.9% at a temperature of 29.9 °C, ethanol to oleic acid molar ratio equal to 4.50:1, and a reaction time of 6.5 h. Additionally, the removal of water from the medium, by using molecular sieves, promoted a 16.0% increase in the conversion of oleic acid into ethyl esters.
RESUMO
In this work, the environmental compatibility of a biosurfactant produced by a Bacillus subtilis strain isolated from the soil of a Brazilian mangrove was investigated. The biosurfactant, identified as surfactin, is able to reduce surface tension (ST) to 31.5 ± 0.1 mN m-1 and exhibits a lowcritical micelle concentration (CMC) value (0.015 ± 0.003 g L-1). The highest crude biosurfactant concentration (224.3 ± 1.9 mg L-1) was reached at 72 h of fermentation. Acute toxicity tests, carried out with Daphnia magna, Vibrio fischeri and Selenastrum capricornutum indicated that the toxicity of the biosurfactant is lower than that of its chemically derived counterparts. The results of the biodegradability tests demonstrated that the crude surfactin extract was degraded by both Pseudomonas putida and a mixed population from a sewage-treatment plant, in both cases the biodegradation efficiency being dependent on the initial concentration of the biosurfactant. Finally, as the biodegradation percentages obtained fall within the acceptance limits established by the Organization for Economic Co-operation and Development (Guidelines for Testing of Chemicals, OECD 301E), crude surfactin can be classified as a "readily" biodegradable compound.