Truly stentless molded autologous pericardial aortic valve prosthesis with single point attached commissures in a sheep model.

OBJECTIVE: Aortic valve cusp extension and free-hand aortic valve replacement with autologous pericardium has been described. The long-term results were shown to be comparable with commercially available aortic bioprostheses. Nevertheless the relatively demanding surgical technique could not find wide acceptance. We developed a new design of a molded aortic valve, fashioned from autologous pericardium, treated briefly with glutaraldehyde, and simplified the implantation technique using single point attached commissures (SPAC). METHODS: Molded autologous valve prostheses were implanted in the subcoronary aortic position in 10 sheep with the commissures connected to the aortic wall at three single commissural points (SPAC). The prosthesis mean size was 21.6+/-1.3 mm and the construction time (excluding 10 min glutaraldehyde treatment) was 6.2+/-1.2 min. Cardiopulmonary bypass and cross-clamp time was 111.1+/-12.4 min and 75.0+/-16.3 min, respectively. Six sheep were euthanized after 201.2+/-10.3 days (6 months) and four sheep were euthanized after 330.8+/-6.5 days (11 months) postoperatively. RESULTS: In all sheep, the valve was immediately competent. At sacrifice, SPAC has proven to be well anchored to the aortic wall and the pericardial valve to be pliable in all cases. The maximum transvalvular gradient after cardiopulmonary bypass and at sacrifice was 3.7+/-2.2 mmHg and 10.6+/-5.2 mmHg, respectively. CONCLUSIONS: This new truly stentless molded autologous aortic valve with simplified implantation technique (SPAC) makes a reliable implantation in a standard timeframe possible. The simplicity of construction, low cost and absent need for anticoagulation of this molded autologous aortic bioprosthesis offers an attractive alternative and not only for patients in the developing world.

Autologous pericardial pulmonary conduit with single point attached commissures in a sheep model.

OBJECTIVE: For the surgical treatment of congenital heart disease and in Ross procedure a valved conduit is frequently required. Since homografts are not readily available in every country, a reliable alternative is needed. We developed a novel technique to construct a valved pulmonary conduit with single point attached commissures (SPAC) in a simple and fast way from a small strip of autologous pericardium, molded and briefly treated with glutaraldehyde. METHODS: Autologous pericardial pulmonary conduit was constructed intraoperatively and implanted in pulmonary position in a beating heart in six sheep. The prosthesis size was 31 mm for all sheep and the construction time (including 10 min glutaraldehyde treatment) was 19.0+/-3.3 min. Implantation time and cardiopulmonary by-pass was 27.3+/-5.4 min and 40.5+/-7.7 min, respectively. The sheep were euthanized after 6 months (222.7+/-5.8 days) postoperatively. RESULTS: In all sheep, the autologous pericardial valve was immediately competent. At sacrifice, the pericardial valve was pliable and competent in all cases with SPAC well anchored to the pericardial conduit wall. The maximum transvalvular gradient at implant and at sacrifice was 3.3+/-2.8 mmHg and 3.3+/-2.0 mmHg, respectively. CONCLUSIONS: This novel autologous pericardial pulmonary conduit with SPAC can be reliably produced in a very short time intraoperatively before cardiopulmonary by-pass. The simplicity of construction, biocompatibility and freedom of stenosis or thrombosis makes this autologous pulmonary conduit especially useful for patients at locations where homografts are not readily available.

Ventriculo-aortic junction in human root. A geometric approach.

With advances in tissue engineering and improvement of surgical techniques, stentless biological valves and valve-sparing procedures have become alternatives to traditional aortic valve replacement with stented bioprostheses or mechanical valves. New surgical techniques preserve the advantages of native valves but require better understanding of the anatomical structure of the aortic root. Silicone rubber was injected in fresh aortic roots of nine human cadavers under the physiological closing pressure of 80 mmHg. The casts reproduced every detail of the aortic root anatomy and were used to digitize 27 leaflet attachment lines (LALs) of the aortic valves. LALs were normalized and described with a mathematical model. LALs were found to follow a pattern with the right coronary being the largest followed by the non-coronary and then the left coronary. During diastole, the aortic valve LAL can be described by an intersection between a created tube and an extruded parabolic surface. This geometrical definition of the LAL during end diastole gives a better understanding of the aortic root anatomy and could be useful for heart valve design and improvement of aortic valve reconstruction technique.

Forces at single point attached commissures (SPAC) in pericardial aortic valve prosthesis.

OBJECTIVE: New pericardial aortic bioprostheses (3F Therapeutics and temporarily stented autologous pericardial valve prosthesis) were developed recently. These valves are designed with commissures connected to the aortic wall at only three single points (single point attached commissures (SPAC)). The aim of this study was to investigate the forces acting on SPAC during varying pressure load. METHODS: Aortic roots with diameters 19, 25, and 29 mm were made using silicone polymer. A bovine pericardial SPAC aortic valve prosthesis was constructed using a 3D-mold and was implanted in the silicone aortic root. The base of the valve was sutured onto the aortic annulus with 4-0 polypropylene running suture and each commissure was sutured to a miniaturized force transducer with only one 3-0 polypropylene U-stitch. Three silicon aortic roots of each size were pressurized up to 200 mmHg and forces on SPAC were measured. RESULTS: All valves remained competent at a pressure of 200 mmHg. Recordings showed a linear correlation between applied pressure and forces measured at SPAC. At a pressure of 80 mmHg (equivalent to diastolic pressure), the forces were 0.44+/-0.22N, 1.15+/-0.18N, and 2.00+/-0.35N in annular diameters 19 mm, 25 mm, and 29 mm, respectively. It was observed, that the main forces were acting along the axial direction and not along the radial direction. CONCLUSIONS: Forces on "single point attached commissures" in pericardial aortic valves were measured. These forces were acting mainly in axial direction and not in radial direction. This knowledge is important for the implantation technique of SPAC pericardial aortic valves.