Three-dimensional printing in cardiac surgery and interventional cardiology: a single-centre experience.

OBJECTIVES: In individual cases, routine preoperative imaging might not be sufficient for optimal planning of cardiovascular procedures. Three-dimensional printing (3D), a widely used technique to build life-like replicas of anatomical structures that has proven value in different medical disciplines, might overcome these shortcomings. However, data on 3D printing in cardiovascular medicine are limited to single reports. This stimulated us to present our single-centre experience with 3D printing models in cardiac surgery and interventional cardiology. METHODS: Between the years 2006 and 2013, we fabricated 3D printing models using preoperative computed tomography or magnetic resonance imaging data in paediatric and adult cardiac surgery, as well as interventional cardiology. We present the 8 most representative cases. RESULTS: The models were very helpful for perioperative planning and orientation, as well as simulation of procedures due to the exact and life-like illustration of the cardiovascular anatomy. CONCLUSIONS: The fabrication of 3D printing models is feasible for perioperative planning and simulation in a variety of complex cases in paediatric and adult cardiac surgery, as well as in interventional cardiology. Further studies including more patients and providing more data are expected to demonstrate that the use of 3D printing may decrease morbidity and mortality of complex, non-routine procedures in cardiovascular medicine.

3-dimensional printing of models to create custom-made devices for coil embolization of an anastomotic leak after aortic arch replacement.

PURPOSE: The objective of this study was to show the use of 3-dimensional printing models to fabricate a custom-made occluder for device embolization of an anastomotic leak after replacement of the ascending aorta and the aortic arch in a human immunodeficiency virus (HIV)-infected patient. DESCRIPTION: We present a 50-year-old HIV-infected patient who underwent ascending aorta and aortic arch replacement for a type A dissection, and who had an aortic arch pseudoaneurysm (sized 5 x 5 x 4 cm) with a slit-shaped entrance hole located anteriorly to the implanted supra-aortic vessels. The patient's 128-slice computed tomography data were visualized and reconstructed. Afterward we fabricated a life-like replica of the complex pathology of the ascending aorta and the aortic arch using a rapid prototyping machine. After careful examination of the model, we fabricated a custom-made occluder device for interventional closure of the leakage. EVALUATION: Using data derived from 128-slid computed tomography linked to proprietary software, we were able to create models of the ascending aorta, the aortic arch end, especially the pseudoaneurysm with its slit-shaped opening between the aortic lumen and the aneurysm. This was very helpful to build a perfectly fitting custom-made occluder device to plan and simulate the interventional closure. Moreover, the models were helpful for intra-interventional orientation. CONCLUSIONS: The stereolithographic replicas were extremely useful for choosing the treatment option and for planning and simulating the occlusion of the pseudoaneurysm. Furthermore, the models were necessary for our engineers who were building the custom-made occluder device.

Three-dimensional printing creates models for surgical planning of aortic valve replacement after previous coronary bypass grafting.

PURPOSE: Resternotomy for aortic valve replacement in patients with previous coronary artery bypass grafting and an internal mammary artery graft may be a surgical problem. Thus, we are exploring the effect of using rapid prototyping techniques for surgical planning and intraoperative orientation during aortic valve replacement after previous coronary artery bypass grafting (CABG). DESCRIPTION: As a proof of concept, we studied a patient who had undergone CABG 5 years earlier. At that time the patient received a left internal mammary artery graft to the left anterior descending artery and a venous graft to the right coronary artery. Now the patient required aortic valve replacement due to symptomatic aortic valve stenosis. The left internal mammary artery bypass and the right coronary artery bypass were patent and showed good flow in the angiography. The patient was examined by 128-slice computed tomography. The image data were visualized and reconstructed. Afterwards, a replica showing the anatomic structures was fabricated using a rapid prototyping machine. EVALUATION: Using data derived from 128-slice computed tomography angiography linked to proprietary software, we were able to create three-dimensional reconstructions of the vascular anatomy after the previous CABG. The models were sterilized and taken to the operating theatre for orientation during the surgical procedure. CONCLUSIONS: Stereolithographic replicas are helpful for choosing treatment strategies in surgical planning and for intraoperative orientation during reoperations of patients with previous CABG.