Broadband and low-loss TM-pass polarizer using tilted subwavelength structures.

Photonic systems built on the Silicon-on-Insulator platform exhibit a strong birefringence, and must thus be operated with a single polarization for most applications. Hence, on-chip polarizers that can effectively suppress an undesired polarization state are key components for these systems. Polarizers that extinguish TE polarized light while letting TM polarized light pass with low losses are particularly challenging to design for the standard 220 nm Silicon-on-Insulator platform, because the modal confinement is stronger for TE polarization than for TM polarzation. Here, we propose and design a broadband, low loss and high extinction ratio TM-pass polarizer by engineering a Bragg grating that reflects the fundamental TE mode into the first order TE mode using a subwavelength metamaterial which at the same time allows the TM mode to pass. Our device achieves an extinction ratio in excess of 20 dB, insertion losses below 0.5 dB and back-reflections of the fundamental TE mode of the order of -20 dB in a bandwidth of 150 nm as demonstrated with full 3D-FDTD simulations.

Broadband 2 × 2 multimode interference coupler for mid-infrared wavelengths.

Beam splitters are core components of photonic integrated circuits and are often implemented with multimode interference couplers. While these devices offer high performance, their operational bandwidth is still restrictive for sensing applications in the mid-infrared wavelength range. Here we experimentally demonstrate a subwavelength-structured 2×2 multimode interference coupler with high performance in the 3.1-3.7µm range, doubling the bandwidth of a conventional device.

Low-loss off-axis curved waveguide grating demultiplexer.

Current optical communication systems rely on the use of wavelength division multiplexing (WDM) to keep up with the increasing data rate requirements. The wavelength demultiplexer is the key component to implement WDM systems. In this Letter, we design and experimentally demonstrate a demultiplexer based on a curved grating waveguide geometry that separates eight channels with a spacing of 10 nm (1249 GHz) around the central wavelength of 1550 nm. The fabricated device shows very low insertion loss (∼1dB) and a crosstalk (XT) below -25dB. This device leverages metamaterial index engineering to implement the lateral cladding on one side of the waveguide. This makes it possible to design a waveguide grating with highly directional lateral emission by operating in a regime where diffraction into the silica upper cladding is frustrated, thus suppressing losses due to off-chip radiation.

High-efficiency conversion from waveguide mode to an on-chip beam using a metamaterial engineered Bragg deflector.

Diffraction gratings that redirect light propagating in a channel waveguide to an on-chip slab are emerging as important building blocks in integrated photonics. Such distributed Bragg deflectors enable precise shaping of slab confined beams for a variety of applications, including wavelength multiplexing, optical phased array feeding, and coupling interfaces for on-chip point-to-point communications. However, these deflectors suffer from significant losses caused by off-chip radiation. In this Letter, we show, for the first time, to the best of our knowledge, that off-chip radiation can be dramatically reduced by using the single-beam phase matching condition and subwavelength metamaterial refractive index engineering. We present a deflector design with losses below 0.3 dB, opening a path toward new applications of distributed Bragg deflectors in integrated photonics.

Coherent silicon photonic interferometric biosensor with an inexpensive laser source for sensitive label-free immunoassays.

Over the past two decades, integrated photonic sensors have been of major interest to the optical biosensor community due to their capability to detect low concentrations of molecules with label-free operation. Among these, interferometric sensors can be read-out with simple, fixed-wavelength laser sources and offer excellent detection limits but can suffer from sensitivity fading when not tuned to their quadrature point. Recently, coherently detected sensors were demonstrated as an attractive alternative to overcome this limitation. Here we show, for the first time, to the best of our knowledge, that this coherent scheme provides sub-nanogram per milliliter limits of detection in C-reactive protein immunoassays and that quasi-balanced optical arm lengths enable operation with inexpensive Fabry-Perot-type lasers sources at telecom wavelengths.

Narrowband Bragg filters based on subwavelength grating waveguides for silicon photonic sensing.

Subwavelength grating (SWG) waveguides have been shown to provide enhanced light-matter interaction resulting in superior sensitivity in integrated photonics sensors. Narrowband integrated optical filters can be made by combining SWG waveguides with evanescently coupled Bragg gratings. In this paper, we assess the sensing capabilities of this novel filtering component with rigorous electromagnetic simulations. Our design is optimized for an operating wavelength of 1310 nm to benefit from lower water absorption and achieve narrower bandwidths than at the conventional wavelength of 1550 nm. Results show that the sensor achieves a sensitivity of 507 nm/RIU and a quality factor of 4.9 × 104, over a large dynamic range circumventing the free spectral range limit of conventional devices. Furthermore, the intrinsic limit of detection, 5.1 × 10-5 RIU constitutes a 10-fold enhancement compared to state-of-the-art resonant waveguide sensors.

Highly efficient optical antenna with small beam divergence in silicon waveguides.

Optical antennas are key components in optical phased arrays for light detection and ranging technology requiring long sensing range and high scanning resolution. To achieve a narrow beam width in the far-field region, antenna lengths of several millimeters or more are required. To date, such long antennas have been impossible to achieve in silicon waveguides because currently demonstrated technologies do not allow accurate control of grating strength. Here, we report on a new type of surface-emitting silicon waveguide with a dramatically increased antenna length of L=3.65mm. This is achieved by using a subwavelength metamaterial waveguide core evanescently coupled with radiative segments laterally separated from the core. This results in a far-field diffracted beam width of 0.025°, which is a record small beam divergence for a silicon photonics surface-emitting device. We also demonstrate that by using a design with L-shaped surface-emitting segments, the radiation efficiency of the antenna can be substantially increased compared to a conventional design, with an efficiency of 72% at the wavelength of 1550 nm.

Polarization splitting directional coupler using tilted subwavelength gratings.

On-chip polarization splitters are key elements for coherent optical communication systems and polarization diversity circuits. These devices are often implemented with directional couplers that are symmetric for one polarization and strongly asymmetric for the other polarization. To achieve this asymmetry, highly dissimilar waveguides are used in each coupler arm, often requiring additional material layers or etch steps. Here we demonstrate polarization splitting with a directional coupler composed of two fully etched subwavelength waveguides, differing only in the tilt angle of the silicon segments. Our device exhibits deep-UV compatible feature sizes, is 14 µm long, and covers a 72 nm bandwidth with insertion losses below 1 dB and an extinction ratio in excess of 15 dB.

Experimental demonstration of metamaterial anisotropy engineering for broadband on-chip polarization beam splitting.

Subwavelength metamaterials exhibit a strong anisotropy that can be leveraged to implement high-performance polarization handling devices in silicon-on-insulator. Whereas these devices benefit from single-etch step fabrication, many of them require small feature sizes or specialized cladding materials. The anisotropic response of subwavelength metamaterials can be further engineered by tilting its constituent elements away from the optical axis, providing an additional degree of freedom in the design. In this work, we demonstrate this feature through the design, fabrication and experimental characterization of a robust multimode interference polarization beam splitter based on tilted subwavelength gratings. A 110-nm minimum feature size and a standard silicon dioxide cladding are maintained. The resulting device exhibits insertion loss as low as 1 dB, an extinction ratio better than 13 dB in a 120-nm bandwidth, and robust tolerances to fabrication deviations.

Distributed Bragg deflector coupler for on-chip shaping of optical beams.

In integrated optical circuits light typically travels in waveguides which provide both vertical and horizontal confinement, enabling efficient routing between different parts of the chip. However, for a variety of applications, including on-chip wireless communications, steerable phased arrays or free-space inspired integrated optics, optical beams that can freely propagate in the horizontal plane of a 2D slab waveguide are advantageous. Here we present a distributed Bragg deflector that enables well controlled coupling from a waveguide mode to such a 2D on-chip beam. The device consists of a channel waveguide and a slab waveguide region separated by a subwavelength metamaterial spacer to prevent uncontrolled leakage of the guided mode. A blazed grating in the waveguide sidewall is used to gradually diffract light into the slab region. We develop a computationally efficient strategy for designing gratings that generate arbitrarily shaped beams. As a proof-of-concept we design, in the silicon-on-insulator platform, a compact ×75 Gaussian beam expander and a partial beam deflector. For the latter, we also demonstrate a prototype device with experimental results showing good agreement with our theoretical predictions. We also demonstrate via a rigorous simulation that two such couplers in a back-to-back configuration efficiently couple light, suggesting that these devices can be used as highly directive antennas in the chip plane.

Optimizing the Limit of Detection of Waveguide-Based Interferometric Biosensor Devices.

Waveguide-based photonic sensors provide a unique combination of high sensitivity, compact size and label-free, multiplexed operation. Interferometric configurations furthermore enable a simple, fixed-wavelength read-out making them particularly suitable for low-cost diagnostic and monitoring devices. Their limit of detection, i.e., the lowest analyte concentration that can be reliably observed, mainly depends on the sensors response to small refractive index changes, and the noise in the read-out system. While enhancements in the sensors response have been extensively studied, noise optimization has received much less attention. Here we show that order-of-magnitude enhancements in the limit of detection can be achieved through systematic noise reduction, and demonstrate a limit of detection of ∼ 10 - 8 RIU with a silicon nitride sensor operating at telecom wavelengths.

Fundamental limit of detection of photonic biosensors with coherent phase read-out.

Photonic biosensors offer label-free detection of biomolecules for applications ranging from clinical diagnosis to food quality monitoring. Both sensors based on Mach-Zehnder interferometers and ring resonators are widely used, but are usually read-out using different schemes, making a direct comparison of their fundamental limit of detection challenging. A coherent detection scheme, adapted from optical communication systems, has been recently shown to achieve excellent detection limits, using a simple fixed-wavelength source. Here we present, for the first time, a theoretical model to determine the fundamental limit of detection of such a coherent read-out system, for both interferometric and resonant sensors. Based on this analysis, we provide guidelines for sensor optimization in the presence of optical losses and show that interferometric sensors are preferable over resonant structures when the sensor size is not limited by the available sample volume.

Bragg filter bandwidth engineering in subwavelength grating metamaterial waveguides.

Bragg gratings are fundamental building blocks for integrated photonic circuits. In the high-index contrast silicon-on-insulator material platform, it is challenging to accurately control the grating strength and achieve narrow spectral bandwidths. Here we demonstrate a novel Bragg grating geometry utilizing a silicon subwavelength grating (SWG) waveguide with evanescently coupled periodic Bragg loading segments placed outside the SWG core. We report experimental 3 dB filter bandwidths in a range from 8 nm to 150 pm by adjusting the distance of the Bragg loading segments from the core and the relative phase shift of the segments on the two sides of the waveguide, with a structure that has a minimum feature size of 100 nm.

Tilted subwavelength gratings: controlling anisotropy in metamaterial nanophotonic waveguides.

Subwavelength grating (SWG) structures are an essential tool in silicon photonics, enabling the synthesis of metamaterials with a controllable refractive index. Here we propose, for the first time to the best of our knowledge, tilting the grating elements to gain control over the anisotropy of the metamaterial. Rigorous finite difference time domain simulations demonstrate that a 45° tilt results in an effective index variation on the fundamental TE mode of 0.23 refractive index units, whereas the change in the TM mode is 20 times smaller. Our simulation predictions are corroborated by experimental results. We furthermore propose an accurate theoretical model for designing tilted SWG structures based on rotated uniaxial crystals that is functional over a wide wavelength range and for both the fundamental and higher order modes. The proposed control over anisotropy opens promising venues in polarization management devices and transformation optics in silicon photonics.

Subwavelength integrated photonics.

In the late nineteenth century, Heinrich Hertz demonstrated that the electromagnetic properties of materials are intimately related to their structure at the subwavelength scale by using wire grids with centimetre spacing to manipulate metre-long radio waves. More recently, the availability of nanometre-scale fabrication techniques has inspired scientists to investigate subwavelength-structured metamaterials with engineered optical properties at much shorter wavelengths, in the infrared and visible regions of the spectrum. Here we review how optical metamaterials are expected to enhance the performance of the next generation of integrated photonic devices, and explore some of the challenges encountered in the transition from concept demonstration to viable technology.

Experimental demonstration of an apodized-imaging chip-fiber grating coupler for Si3N4 waveguides.

A silicon nitride waveguide is a promising platform for integrated photonics, particularly due to its low propagation loss compared to other complementary metal-oxide-semiconductor compatible waveguides, including silicon-on-insulator. Input/output coupling in such thin optical waveguides is a key issue for practical implementations. Fiber-to-chip grating couplers in silicon nitride usually exhibit low coupling efficiency because the moderate index contrast leads to weak radiation strengths and poor directionality. Here, we present the first, to the best of our knowledge, experimental demonstration of a recently proposed apodized-imaging fiber-to-chip grating coupler in silicon nitride that images an in-plane waveguide mode to an optical fiber placed at a specific distance above the chip. By employing amplitude and phase apodization, the diffracted optical field of the grating is matched to the fiber mode. High grating directionality is achieved by using staircase grating teeth, which produce a blazing effect. Experimental results demonstrate an apodized-imaging grating coupler with a record coupling efficiency of -1.5 dB and a 3 dB bandwidth of 60 nm in the C-band.

Disorder effects in subwavelength grating metamaterial waveguides.

Subwavelength grating (SWG) waveguides are integrated photonic structures with a pitch substantially smaller than wavelength for which they are designed, so that diffraction effects are suppressed. SWG operates as an artificial metamaterial with an equivalent refractive index which depends on the geometry of the structure and the polarization of the propagating wave. SWG waveguides have been advantageously used in silicon photonics, resulting in significant performance improvements for many practical devices, including highly efficient fiber-chip couplers, waveguide crossings, broadband multimode interference (MMI) couplers, evanescent field sensors and polarization beam splitters, to name a few. Here we present a theoretical and experimental study of the influence of disorder effects in SWG waveguides. We demonstrate via electromagnetic simulations and experimental measurements that even a comparatively small jitter (~5 nm) in the position and size of the SWG segments may cause a dramatic reduction in the transmittance for wide (multimode) SWG waveguides, while for narrow (single mode) waveguides this effect is negligible. Our study shows that the impact of the jitter on SWG waveguide performance is directly related to the modal confinement.

High-efficiency apodized-imaging chip-fiber grating coupler for silicon nitride waveguides.

Chip-fiber grating couplers have been widely used in silicon-on-insulator platforms. In silicon nitride waveguides, the lower index contrast yields gratings with a weaker radiation strength and poor directionality, thereby limiting the coupling efficiency. Here we propose and design an apodized self-imaging grating coupler in silicon nitride that images an in-plane waveguide input to an output optical fiber placed at a specific distance above the chip. Both amplitude and phase apodizations are employed to engineer the transfer function of the self-imaging grating to produce an image field matching the fiber mode profile. Two-step etch staircase grating teeth are used to achieve directionality as high as 93%. Full three-dimensional finite-difference time-domain simulations show coupling from a 40 µm×40 µm grating to an SMF-28 single mode fiber with a record calculated efficiency of 86% (0.66 dB loss) and a 3 dB bandwidth of 40 nm near the 1550 nm wavelength.

Single-etch subwavelength engineered fiber-chip grating couplers for 1.3 µm datacom wavelength band.

We report, for the first time, on the design and experimental demonstration of fiber-chip surface grating couplers based on subwavelength grating engineered nanostructure operating in the low fiber chromatic dispersion window (around 1.3 µm wavelengths), which is of great interest for short-reach data communication applications. Our coupler designs meet the minimum feature size requirements of large-volume deep-ultraviolet stepper lithography processes. The fiber-chip couplers are implemented in a standard 220-nm-thick silicon-on-insulator (SOI) platform and are fabricated by using a single etch process. Several types of couplers are presented, specifically the uniform, the apodized, and the focusing designs. The measured peak coupling efficiency is -2.5 dB (56%) near the central wavelength of 1.3 µm. In addition, by utilizing the technique of the backside substrate metallization underneath the grating couplers, the coupling efficiency of up to -0.5 dB (89%) is predicted by Finite Difference Time Domain (FDTD) calculations.

Broadband fiber-chip zero-order surface grating coupler with 0.4 dB efficiency.

Surface grating couplers enable efficient coupling of light between optical fibers and nanophotonic waveguides. However, in conventional grating couplers, the radiation angle is intrinsically wavelength dependent, thereby limiting their operation bandwidth. In this Letter, we present a zero-order surface grating coupler in silicon-on-insulator which overcomes this limitation by operating in the subwavelength regime. By engineering the effective refractive index of the grating region, both high coupling efficiency and broadband operation bandwidth are achieved. The grating is assisted by a silicon prism on top of the waveguide, which favors upward radiation and minimizes power losses to substrate. Using a linear apodization, our design achieves a coupling efficiency of 91% (-0.41 dB) and a 1-dB bandwidth of 126 nm.