Reduction of GaAs Buffer Thickness and Its Impact on Epitaxially Integrated III-V Quantum Dot Lasers on a Si Substrate.

Monolithic integration of III-V quantum dot (QD) lasers onto a Si substrate is a scalable and reliable approach for obtaining highly efficient light sources for Si photonics. Recently, a combination of optimized GaAs buffers and QD gain materials resulted in monolithically integrated butt-coupled lasers on Si. However, the use of thick GaAs buffers up to 3 µm not only hinders accurate vertical alignment to the Si optical waveguide but also imposes considerable growth costs and time constraints. Here, for the first time, we demonstrate InAs QD lasers epitaxially grown on a 700 nm thick GaAs/Si template, which is approximately four times thinner than the conventional III-V buffers on Si. The optimized 700 nm GaAs buffer yields a remarkably smooth surface and low threading dislocation density of 4 × 108 cm-2, which is sufficient for QD laser growth. The InAs QD lasers fabricated on these ultrathin templates still lase at room temperature with a threshold current density of 661 A/cm2 and a characteristic temperature of 50 K. We believe that these results are important for the monolithically integrated III-V QD lasers for Si photonics applications.

Low-threshold 2†µm InAs/InP quantum dash lasers enabled by punctuated growth.

2 µm photonics and optoelectronics is promising for potential applications such as optical communications, LiDAR, and chemical sensing. While the research on 2 µm detectors is on the rise, the development of InP-based 2 µm gain materials with 0D nanostructures is rather stalled. Here, we demonstrate low-threshold, continuous wave lasing at 2 µm wavelength from InAs quantum dash/InP lasers enabled by punctuated growth of the quantum structure. We demonstrate low threshold current densities from the 7.1 µm width ridge-waveguide lasers, with values of 657, 1183, and 1944 A/cm2 under short pulse wave (SPW), quasi-continuous wave (QCW), and continuous wave operation. The lasers also exhibited good thermal stability, with a characteristic temperature T0 of 43 K under SPW mode. The lasing spectra is centered at 1.97 µm, coinciding with the ground-state emission observed from photoluminescence studies. We believe that the InAs quantum dash/InP lasers emitting near 2 µm will be a key enabling technology for 2 µm communication and sensing.

Demonstration of programmable light intensity of a micro-LED with a Hf-based ferroelectric ITZO TFT for Mura-free displays.

We demonstrate the programmable light intensity of a micro-LED by compensating threshold voltage variability of thin-film transistors (TFTs) by introducing a non-volatile programmable ferroelectric material, HfZrO2 (HZO) into the gate stack of the TFT. We fabricated an amorphous ITZO TFT, ferroelectric TFTs (FeTFTs), and micro-LEDs and verified the feasibility of our proposed current-driving active matrix circuit. Importantly, we successfully present the programmed multi-level lighting of the micro-LED, utilizing partial polarization switching in the a-ITZO FeTFT. We expect that this approach will be highly promising for the next-generation display technology, replacing complicated threshold voltage compensation circuits with a simple a-ITZO FeTFT.

High-sensitivity waveguide-integrated bolometer based on free-carrier absorption for Si photonic sensors.

Conventional photon detectors necessarily face critical challenges regarding strong wavelength-selective response and narrow spectral bandwidth, which are undesirable for spectroscopic applications requiring a wide spectral range. With this perspective, herein, we overcome these challenges through a free-carrier absorption-based waveguide-integrated bolometer for infrared spectroscopic sensors on a silicon-on-insulator (SOI) platform featuring a spectrally flat response at near-infrared (NIR) range (1520-1620 nm). An in-depth thermal analysis was conducted with a systematic investigation of geometry dependence on the detectors. We achieved great performances: temperature coefficient of resistance (TCR) of -3.786%/K and sensitivity of -26.75%/mW with a low wavelength dependency, which are record-high values among reported waveguide bolometers so far, to our knowledge. In addition, a clear on-off response with the rise/fall time of 24.2/29.2 µs and a 3-dB roll-off frequency of ∼22 kHz were obtained, sufficient for a wide range of sensing applications. Together with the possibility of expanding an operation range to the mid-infrared (MIR) band, as well as simplicity in the detector architecture, our work here presents a novel strategy for integrated photodetectors covering NIR to MIR at room temperature for the development of the future silicon photonic sensors with ultrawide spectral bandwidth.

Enhanced Photoluminescence of 1.3 µm InAs Quantum Dots Grown on Ultrathin GaAs Buffer/Si Templates by Suppressing Interfacial Defect Emission.

We report on the photoluminescence enhancement of 1.3 µm InAs quantum dots (QDs) epitaxially grown on an ultrathin 250 nm GaAs buffer on a Si substrate. Decreasing the GaAs buffer thickness from 1000 to 250 nm was found to not only increase the coalesced QD density from 6.5 × 108 to 1.9 × 109 cm-2 but also decrease the QD photoluminescence emission intensity dramatically. Inserting an Al0.4Ga0.6As potential barrier layer maintained strong photoluminescence from the QDs by effectively suppressing carrier leakage to the GaAs/Si interfacial region even when the GaAs buffer was thinned to 250 nm. We then fabricated a light-emitting diode using the ultrathin 250 nm GaAs buffer on Si and confirmed strong electroluminescence peaking at 1.28 µm without interfacial defect emission at room temperature. We believe that this work is promising for monolithically integrated evanescent Si lasers using InAs/GaAs QDs.

Energy-Efficient III-V Tunnel FET-Based Synaptic Device with Enhanced Charge Trapping Ability Utilizing Both Hot Hole and Hot Electron Injections for Analog Neuromorphic Computing.

A charge trap device based on field-effect transistors (FET) is a promising candidate for artificial synapses because of its high reliability and mature fabrication technology. However, conventional MOSFET-based charge trap synapses require a strong stimulus for synaptic update because of their inefficient hot-carrier injection into the charge trapping layer, consequently causing a slow speed operation and large power consumption. Here, we propose a highly efficient charge trap synapse using III-V materials-based tunnel field-effect transistor (TFET). Our synaptic TFETs present superior subthreshold swing and improved charge trapping ability utilizing both carriers as charge trapping sources: hot holes created by impact ionization in the narrow bandgap InGaAs after being provided from the p+-source, and band-to-band tunneling hot electrons (BBHEs) generated at the abrupt p+n junctions in the TFETs. Thanks to these advances, our devices achieved outstanding efficiency in synaptic characteristics with a 5750 times faster synaptic update speed and 51 times lower sub-fJ/um2 energy consumption per single synaptic update in comparison to the MOSFET-based synapse. An artificial neural network (ANN) simulation also confirmed a high recognition accuracy of handwritten digits up to ∼90% in a multilayer perceptron neural network based on our synaptic devices.

High-Performance Flexible InAs Thin-Film Photodetector Arrays with Heteroepitaxial Growth Using an Abruptly Graded InxAl1-xAs Buffer.

Current infrared thermal image sensors are mainly based on planar firm substrates, but the rigid form factor appears to restrain the versatility of their applications. For wearable health monitoring and implanted biomedical sensing, transfer of active device layers onto a flexible substrate is required while controlling the high-quality crystalline interface. Here, we demonstrate high-detectivity flexible InAs thin-film mid-infrared photodetector arrays through high-yield wafer bonding and a heteroepitaxial lift-off process. An abruptly graded InxAl1-xAs (0.5 < x < 1) buffer was found to drastically improve the lift-off interface morphology and reduce the threading dislocation density twice, compared to the conventional linear grading method. Also, our flexible InAs photodetectors showed excellent optical performance with high mechanical robustness, a peak room-temperature specific detectivity of 1.21 × 109 cm-Hz1/2/W at 3.4 µm, and excellent device reliability. This flexible InAs photodetector enabled by the heteroepitaxial lift-off method shows promise for next-generation thermal image sensors.

Heterogeneously-Integrated Optical Phase Shifters for Next-Generation Modulators and Switches on a Silicon Photonics Platform: A Review.

The realization of a silicon optical phase shifter marked a cornerstone for the development of silicon photonics, and it is expected that optical interconnects based on the technology relax the explosive datacom growth in data centers. High-performance silicon optical modulators and switches, integrated into a chip, play a very important role in optical transceivers, encoding electrical signals onto the light at high speed and routing the optical signals, respectively. The development of the devices is continuously required to meet the ever-increasing data traffic at higher performance and lower cost. Therefore, heterogeneous integration is one of the highly promising approaches, expected to enable high modulation efficiency, low loss, low power consumption, small device footprint, etc. Therefore, we review heterogeneously integrated optical modulators and switches for the next-generation silicon photonic platform.

Ultra-Lightweight, Flexible InGaP/GaAs Tandem Solar Cells with a Dual-Function Encapsulation Layer.

Lightweight, flexible solar cells from III-V semiconductors offer new application opportunities for devices that require a power supply, such as cars, drones, satellites, or wearable devices, due to their outstanding efficiency and power-to-weight ratio (specific power). However, the specific power and stability of flexible photovoltaic (PV) devices need to be enhanced for use in such applications because current flexible PV devices are vulnerable to moisture and heat. Here, we develop ultra-lightweight, flexible InGaP/GaAs tandem solar cells with a dual-function encapsulation layer that serves as both a moisture barrier and an antireflection coating for the active device layer. Using a thin polymer film as a substrate and an ultrathin metal as a bonding layer, the total weight of the device is dramatically reduced. Therefore, the specific power of our solar cells is remarkably high with a value of over 5000 W/kg under the AM 1.5G solar spectrum. Additionally, there is no degradation even if the solar cells are exposed to harsh environmental conditions.

Flexible GaAs photodetector arrays hetero-epitaxially grown on GaP/Si for a low-cost III-V wearable photonics platform.

We demonstrate flexible GaAs photodetector arrays that were hetero-epitaxially grown on a Si wafer for a new cost-effective and reliable wearable optoelectronics platform. A high crystalline quality GaAs layer was transferred onto a flexible foreign substrate and excellent retention of device performance was demonstrated by measuring the optical responsivities and dark currents. Optical simulation proves that the metal stacks used for wafer bonding serve as a back-reflector and enhance GaAs photodetector responsivity via a resonant-cavity effect. Device durability was also tested by bending 1000 times and no performance degradation was observed. This work paves a way for a cost-effective and flexible III-V optoelectronics technology with high durability.

3D Stackable Synaptic Transistor for 3D Integrated Artificial Neural Networks.

Although they have attracted enormous attention in recent years, software-based and two-dimensional hardware-based artificial neural networks (ANNs) may consume a great deal of power. Because there will be numerous data transmissions through a long interconnection for learning, power consumption in the interconnect will be an inevitable problem for low-power computing. Therefore, we suggest and report 3D stackable synaptic transistors for 3D ANNs, which would be the strongest candidate in future computing systems by minimizing power consumption in the interconnection. To overcome the problems of enormous power consumption, it might be necessary to introduce a 3D stackable ANN platform. With this structure, short vertical interconnection can be realized between the top and bottom devices, and the integration density can be significantly increased for integrating numerous neuromorphic devices. In this paper, we suggest and show the feasibility of monolithic 3D integration of synaptic devices using the channel layer transfer method through a wafer bonding technique. Using a low-temperature processible III-V and composite oxide (Al2O3/HfO2/Al2O3)-based weight storage layer, we successfully demonstrated synaptic transistors showing good linearity (αp/αd = 1.8/0.5), a high transconductance ratio (6300), and very good stability. High learning accuracy of 97% was obtained in the training of 1 million MNIST images based on the device characteristics.

Strategy toward the fabrication of ultrahigh-resolution micro-LED displays by bonding-interface-engineered vertical stacking and surface passivation.

In this study, we proposed a strategy to fabricate vertically stacked subpixel (VSS) micro-light-emitting diodes (µ-LEDs) for future ultrahigh-resolution microdisplays. At first, to vertically stack the LED with different colors, we successfully adopted a bonding-interface-engineered monolithic integration method using SiO2/SiNx distributed Bragg reflectors (DBRs). It was found that an intermediate DBR structure could be used as the bonding layer and color filter, which could reflect and transmit desired wavelengths through the bonding interface. Furthermore, the optically pumped µ-LED array with a pitch of 0.4 µm corresponding to the ultrahigh-resolution of 63 500 PPI could be successfully fabricated using a typical semiconductor process, including electron-beam lithography. Compared with the pick-and-place strategy (limited by machine alignment accuracy), the proposed strategy leads to the fabrication of significantly improved high-density µ-LEDs. Finally, we systematically investigated the effects of surface traps using time-resolved photoluminescence (TRPL) and two-dimensional simulations. The obtained results clearly demonstrated that performance improvements could be possible by employing optimal passivation techniques by diminishing the pixel size for fabricating low-power and highly efficient microdisplays.

High-throughput toxicity study of lubricant emulsions and their common ingredients using zebrafish.

Though lubricant emulsions have been widely used in many industrial processes, various human health hazards have been reported. Conducting a systematic toxicity study on emulsions is difficult since emulsions contain multiple chemical compounds, and hydrophobic compounds form complex emulsion particles via surfactants. For a quantitative toxicity study, we developed a high-throughput imaging system using zebrafish and conducted a large scale in vivo toxicity assay of lubricant emulsion and their common ingredients. By computing the locomotion activity of zebrafish from captured time-lapse images, we could quantify the degree of relative toxicity of 29 chemicals. The changes in the locomotion activity over time were observed to vary significantly depending on emulsions, indicating that the degree of toxicity of the commercial products was very diverse. We found that primary ethanolamines were more toxic than secondary or tertiary ethanolamines, and several factors, such as alkyl chain length, EO mole, test concentration, and emulsion particle size, affected toxicity.

Accepting telemedicine in a circulatory medicine ward in major hospitals in South Korea: patients' and health professionals' perception of real-time electrocardiogram monitoring.

BACKGROUND: South Korean government is currently in progress of expanding the coverage of telemedicine projects as part of an attempt to vitalize service industry, but is facing fierce opposition from KMA. Practice of telemedicine requires sufficient discussions among related parties. Although the participation of medical specialists is important, agreement from the public is essential. METHODS: Three main tertiary care centers in Seoul were selected for data collection. A total of 224 patients (patients n = 180, patient guardian n = 44) and medical professionals (n = 41) were selected using simple random sampling. Mixed method of quantitative survey and qualitative semi-interview was used. RESULTS: This study analyzed patients' and medical professionals' perception about the application of telemedicine in cardiology ward in tertiary care centers to provide baseline data when developing and applying telemedicine services. Results implied high need for encouraging telemedicine projects in order to appeal needs among population by providing experience (p < 0.001) and knowledge (p < 0.001). Other results showed that the need for electrocardiography monitoring was high among not only in remote areas but also in areas close to the capital. 64.52% of all participants thought that telemedicine was needed, and 73.21% of participants were willing to use telemedicine service if provided. Semi-interviews revealed that participants expected more cost and time saving services through remote treatment, by not having to visit long distance hospitals frequently. CONCLUSIONS: Research results oppose Korean Medical Association's opinion that the population is against enforcing telemedicine related laws. The findings in this study reflect an up-to-date perception of telemedicine among patients and medical professionals in a tertiary care centers' cardiology ward. Moreover, the study provides a baseline that is needed in order to overcome past failures and to successfully implement telemedicine in South Korea.

Low temperature Al2O3 surface passivation for carrier-injection SiGe optical modulator.

Surface passivation by Al(2)O(3) deposited by atomic layer deposition (ALD) at 200 °C is examined to suppress surface recombination for carrier-injection SiGe optical modulators. We have investigated the interface trap densities at SiO(2)/Si and Al(2)O(3)/Si interfaces formed by plasma enhanced chemical vapor deposition (PECVD) and ALD, respectively. By evaluating metal-oxide-semiconductor (MOS) capacitors formed on Si surfaces after dry etching, we found that the interface trap density of Al(2)O(3) passivated surface is more than one order of magnitude less than that of SiO(2) passivated one. As a result, the modulation efficiency is improved by 1.3 by inserting Al(2)O(3) layer prior to SiO(2) deposition by PECVD owing to superior interface between Al(2)O(3) and Si. The Al(2)O(3) passivated device exhibits comparable modulation efficiency to a thermally-grown SiO(2) passivated one formed by dry oxidation. Hence, the ALD Al(2)O(3) passivation is effective to passivate SiGe optical modulators for which low temperature processes are required.

Ubiquitous Diabetes Management System via Interactive Communication Based on Information Technologies: Clinical Effects and Perspectives.

New diabetes management systems based on interactive communication have been introduced recently, accompanying rapid advances in information technology; these systems are referred to as "ubiquitous diabetes management systems." In such ubiquitous systems, patients and medical teams can communicate via Internet or telecommunications, with patients uploading their glucose data and personal information, and medical teams sending optimal feedback. Clinical evidence from both long-term and short-term trials has been reported by some researchers. Such systems appear to be effective not only in reducing the levels of HbA1c but also in stabilizing glucose control. However, most notably, evidence for the cost-effectiveness of such a system should be demonstrated before it can be propagated out to the general population in actual clinical practice. To establish a cost-effective model, various types of clinical decision supporting software designed to reduce the labor time of physicians must first be developed. A number of sensors and devices for monitoring patients' data are expected to be available in the near future; thus, methods for automatic interconnections between devices and web charts were also developed. Further investigations to demonstrate the clinical outcomes of such a system should be conducted, hopefully leading to a new paradigm of diabetes management.