A comparative study of the effects of different bioactive fillers in PLGA matrix composites and their suitability as bone substitute materials: A thermo-mechanical and in vitro investigation.

Bone substitute composite materials with poly(L-lactide-co-glycolide) (PLGA) matrices and four different bioactive fillers: CaCO3, hydroxyapatite (HA), 45S5 Bioglass(®) (45S5 BG), and ICIE4 bioactive glass (a lower sodium glass than 45S5 BG) were produced via melt blending, extrusion and moulding. The viscoelastic, mechanical and thermal properties, and the molecular weight of the matrix were measured. Thermogravimetric analysis evaluated the effect of filler composition on the thermal degradation of the matrix. Bioactive glasses caused premature degradation of the matrix during processing, whereas CaCO3 or HA did not. All composites, except those with 45S5 BG, had similar mechanical strength and were stiffer than PLGA alone in compression, whilst all had a lower tensile strength. Dynamic mechanical analysis demonstrated an increased storage modulus (E') in the composites (other than the 45S5 BG filled PLGA). The effect of water uptake and early degradation was investigated by short-term in vitro aging in simulated body fluid, which indicated enhanced water uptake over the neat polymer; bioactive glass had the greatest water uptake, causing matrix plasticization. These results enable a direct comparison between bioactive filler type in poly(α-hydroxyester) composites, and have implications when selecting a composite material for eventual application in bone substitution.

Primary stability in reversed-anatomy glenoid components.

Reversed-anatomy shoulder replacement is advocated for patients with poor rotator cuff condition, for whom an anatomical reconstruction would provide little or no stability. Modern generations of this concept appear to be performing well in the short-term to midterm clinical follow-up. These designs are almost always non-cemented, requiring a high degree of primary stability to encourage bone on-growth and so to establish long-term fixation. Six different inverse-anatomy glenoid implants, currently on the market and encompassing a broad range of geometrical differences, were compared on the basis of their ability to impart primary stability through the minimization of interface micromotions. Fixing screws were only included in the supero-inferior direction in appropriate implants and were always inclined at the steepest available angle possible during surgery (up to a maximum of 30 degrees). The extent of predicted bony on-growth was, of course, highly dependent on the threshold for interface micromotion. In some instances an additional 30 per cent of the interface was predicted to promote bone on-growth when the threshold was raised from 20 microm to 50 microm. With maximum thresholds of micromotion for bone on-growth set to 30 microm, the Zimmer Anatomical device was found to be the most stable of the series of the six designs tested herein, achieving an additional 3 per cent (by surface area) of bone on-growth above the closest peer product (Biomet Verso). When this threshold was raised to 50 microm, the Biomet Verso design was most stable (3 per cent above the second-most stable design, the Zimmer Anatomical). Peak micromotions were not a good indicator of the predicted area of bone on-growth and could lead to some misinterpretation of the implant's overall performance. All but one of the implants tested herein provided primary stability sufficient to resist motions in excess of 150 microm at the interface.

A numerical tool for the reconstruction of the physiological kinematics of the glenohumeral joint.

The aim of this study was to develop and test a robust approach to apply a joint coordinate system (JCS) to imaging data sets of the glenohumeral joint and to reconstruct the kinematics with six degrees of freedom (6DOF) in order to investigate shoulder pathologies related to instability. Visible human data were used to reconstruct bony morphology. Landmarks were used to define axes for body-fixed Cartesian coordinate frames on the humerus and scapula. These were applied to a three-cylinder open-chain JCS upon which the humeral 6DOF motions relative to the scapula were implemented. Software was written that applies 6DOF input variables to rotate and translate the nodes of the surface geometry of the humerus relative to the scapula in a global coordinate frame. The instantaneous relative position and orientation of the humerus for a given set of variables were thus reconstructed on the bone models for graphical display. This tool can be used for graphical animation of shoulder kinematics, demonstrating clinical assessments, and allowing further analysis of the function of tissues within the joint.