Passively mode-locked erbium-doped fiber laser based on a nanodiamond saturable absorber.

In this paper, we propose nanodiamond (ND) material as a saturable absorber (SA) to generate short pulses from a mode-locked erbium-doped fiber laser (EDFL). The ND-SA is fabricated by the drop-casting method using polyvinyledenedifluoride-trifluoroethylene as a host polymer and methyl ethel ketone as a solvent liquid. The SA, which possesses 20% ND concentration, has a 5.46% modulation depth with 2000MW/cm2 saturation intensity. Sequentially, the performance of the EDFL is investigated after integrating an ND-SA within the laser ring. The results reveal that the presented ND-SAs produce stable ultrashort laser pulses. Moreover, the fabricated ND film is a promising solid film for many photonic schemes. The proposed mode-locked EDFL-based ND-SA starts a mode-locking operation at a pumped power of 116 mW. The generated mode-locked pulses have a pulse duration of 0.84 ps, a repetition rate of 1.93 MHz, and a power of 0.517 mW, at a pumped power of 187 mW. Finally, to the best of our knowledge, this is the first time that the ND-SA has been used as a mode locker within the EDFL as a thin film and with the suggested fabrication method.

Q-switched ytterbium-doped fiber laser via a thulium-doped fiber saturable absorber.

We demonstrated a reliable and stable Q-switched ytterbium-doped fiber laser centered at 1069 nm by employing a segment of 11 cm thulium-doped fiber (TDF) as a saturable absorber (SA) in the ring cavity. The fiber SA has an optical absorption of 1.35 dB at the Q-switched operating regime. As we increased the pump power from 109 mW to the maximum available pump power of 206 mW, a consistent Q-switched laser with output power ranging from 1.8 to 4.8 mW was attained. The pulse width narrowed from 4.9 to 2.87 µs, whereas the repetition rate increased from 40 to 60.2 kHz. In addition, maximum pulse energy of 80.7 nJ and a maximum peak power of 28.1 mW were obtained at the maximum pump power. The signal to noise ratio (SNR) was around 47 dB. Our experimental study shows that a segment of TDF can be used as a Q-switcher in the 1 µm fiber laser cavity to facilitate a reliable and robust microsecond pulse generation.

Temperature sensing using CdSe quantum dot doped poly(methyl methacrylate) microfiber.

This work describes noncontact temperature measurements using wavelength shifts of CdSe quantum dot (QD) doped poly(methyl methacrylate) microfiber. The sensor is fabricated using a drawing method by bridging two tapered single mode fibers with a polymer microfiber (PMF) approximately 3 µm in diameter. A set of a PMF section with and without the doping of the CdSe-ZnS core-shell QD was applied as sensing probes and used to measure temperatures over the range of 25°C-48°C. The experimental results show that the doped PMF is able to achieve a higher performance with a reasonably good sensitivity of 58.5 pm/°C based on the wavelength shifting, which is about 18 times that of the undoped PMF temperature sensitivity. The proposed sensor showed a linear temperature sensing range that matches well with the physiologically relevant temperatures. Moreover, these results open the way for long-term and high-stability realization of temperature sensing optical fibers.

Potassium permanganate (KMnO4) sensing based on microfiber sensors.

Two straight microfiber sensors are proposed and demonstrated for the detection of various concentrations of a potassium permanganate (KMnO4) solution. Two types of straight microfibers, namely, silica microfiber and poly(methyl methacrylate) microfiber, have been fabricated by using the flame brushing technique and the direct drawing technique, respectively. Based on the varied KMnO4 concentrations of the solution from 1% to 6%, the measurement of the peak voltage of the transmission power was made. The results show that the sensitivity of the silica microfiber sensor and the polymer microfiber is obtained at 184.5 µW/% and 32.57 µW/% with a resolution of 0.0035% and 0.0064%, respectively. Hence, the silica microfiber is more sensitive than the polymer microfiber for KMnO4 concentration measurements.

Performance analysis of an all-optical OFDM system in presence of non-linear phase noise.

The potential for higher spectral efficiency has increased the interest in all-optical orthogonal frequency division multiplexing (OFDM) systems. However, the sensitivity of all-optical OFDM to fiber non-linearity, which causes nonlinear phase noise, is still a major concern. In this paper, an analytical model for estimating the phase noise due to self-phase modulation (SPM), cross-phase modulation (XPM), and four-wave mixing (FWM) in an all-optical OFDM system is presented. The phase noise versus power, distance, and number of subcarriers is evaluated by implementing the mathematical model using Matlab. In order to verify the results, an all-optical OFDM system, that uses coupler-based inverse fast Fourier transform/fast Fourier transform without any nonlinear compensation, is demonstrated by numerical simulation. The system employs 29 subcarriers; each subcarrier is modulated by a 4-QAM or 16-QAM format with a symbol rate of 25 Gsymbol/s. The results indicate that the phase variance due to FWM is dominant over those induced by either SPM or XPM. It is also shown that the minimum phase noise occurs at -3 dBm and -1 dBm for 4-QAM and 16-QAM, respectively. Finally, the error vector magnitude (EVM) versus subcarrier power and symbol rate is quantified using both simulation and the analytical model. It turns out that both EVM results are in good agreement with each other.

Temperature compensation in determining of Remazol black B concentrations using plastic optical fiber based sensor.

In this study, the construction and test of tapered plastic optical fiber (POF) sensors, based on an intensity modulation approach are described. Tapered fiber sensors with different diameters of 0.65 mm, 0.45 mm, and 0.35 mm, were used to measure various concentrations of Remazol black B (RBB) dye aqueous solutions at room temperature. The concentrations of the RBB solutions were varied from 0 ppm to 70 ppm. In addition, the effect of varying the temperature of the RBB solution was also investigated. In this case, the output of the sensor was measured at four different temperatures of 27 °C, 30 °C, 35 °C, and 40 °C, while its concentration was fixed at 50 ppm and 100 ppm. The experimental results show that the tapered POF with d = 0.45 mm achieves the best performance with a reasonably good sensitivity of 61 × 10(-4) and a linearity of more than 99%. It also maintains a sufficient and stable signal when heat was applied to the solution with a linearity of more than 97%. Since the transmitted intensity is dependent on both the concentration and temperature of the analyte, multiple linear regression analysis was performed to combine the two independent variables into a single equation. The resulting equation was then validated experimentally and the best agreement between the calculated and experimental results was achieved by the sensor with d = 0.45 mm, where the minimum discrepancy is less than 5%. The authors conclude that POF-based sensors are suitable for RBB dye concentration sensing and, with refinement in fabrication, better results could be achieved. Their low fabrication cost, simple configuration, accuracy, and high sensitivity would attract many potential applications in chemical and biological sensing.

Quantification of mesenchymal stem cell growth rates through secretory and excretory biomolecules in conditioned media via Fresnel reflection.

An efficient and low cost optical method for directly measuring the concentration of homogenous biological solutes is proposed and demonstrated. The proposed system operates by Fresnel reflection, with a flat-cleaved single-mode fiber serving as the sensor probe. A laser provides a 12.9 dBm sensor signal at 1,550 nm, while a computer-controlled optical power meter measures the power of the signal returned by the probe. Three different mesenchymal stem cell (MSC) lines were obtained, sub-cultured and trypsinized daily over 9 days. Counts were measured using a haemocytometer and the conditioned media (CM) was collected daily and stored at -80 °C. MSCs release excretory biomolecules proportional to their growth rate into the CM, which changes the refractive index of the latter. The sensor is capable of detecting changes in the number of stem cells via correlation to the change in the refractive index of the CM, with the measured power loss decreasing approximately 0.4 dB in the CM sample per average 1,000 cells in the MSC subculture. The proposed system is highly cost-effective, simple to deploy, operate, and maintain, is non-destructive, and allows reliable real-time measurement of various stem cell proliferation parameters.

Fibre optic sensors for selected wastewater characteristics.

Demand for online and real-time measurements techniques to meet environmental regulation and treatment compliance are increasing. However the conventional techniques, which involve scheduled sampling and chemical analysis can be expensive and time consuming. Therefore cheaper and faster alternatives to monitor wastewater characteristics are required as alternatives to conventional methods. This paper reviews existing conventional techniques and optical and fibre optic sensors to determine selected wastewater characteristics which are colour, Chemical Oxygen Demand (COD) and Biological Oxygen Demand (BOD). The review confirms that with appropriate configuration, calibration and fibre features the parameters can be determined with accuracy comparable to conventional method. With more research in this area, the potential for using FOS for online and real-time measurement of more wastewater parameters for various types of industrial effluent are promising.

Resonance condition of a microfiber knot resonator immersed in liquids.

Effects of immersing a microfiber knot resonator (MKR) in liquid solutions that have refractive indices close to that of silica are experimentally demonstrated and theoretically analyzed. Significant improvement in resonance extinction ratio within 2 to 10 dB was observed. To achieve a better understanding, a qualitative analysis of the coupling ratio and round-trip attenuation of the MKR is performed by using a curve-fitting method. It was observed that the coupling coefficient at the knot region increased when immersed in liquids. However, depending on the initial state of the coupling and the quantity of the increment in the coupling coefficient when immersed in a liquid, it is possible that the MKR may experience a deficit in the coupling parameter due to the sinusoidal relationship with the coupling coefficient.